% Complete documentation on the extended LaTeX markup used for Python
% documentation is available in ``Documenting Python'', which is part
% of the standard documentation for Python.  It may be found online
% at:
%
%     http://www.python.org/doc/current/doc/doc.html

\documentclass[hyperref]{manual}

% latex2html doesn't know [T1]{fontenc}, so we cannot use that:(

\usepackage{amsmath}
\usepackage[latin1]{inputenc}
\usepackage{textcomp}


% The commands of this document do not reset module names at section level
% (nor at chapter level).
% --> You have to do that manually when a new module starts!
%     (use \py@reset)
%begin{latexonly}
\makeatletter
\renewcommand{\section}{\@startsection{section}{1}{\z@}%
   {-3.5ex \@plus -1ex \@minus -.2ex}%
   {2.3ex \@plus.2ex}%
   {\reset@font\Large\py@HeaderFamily}}
\makeatother
%end{latexonly}


% additional mathematical functions
\DeclareMathOperator{\abs}{abs}

% provide a cross-linking command for the index
%begin{latexonly}
\newcommand*\see[2]{\protect\seename #1}
\newcommand*{\seename}{$\to$}
%end{latexonly}


% some convenience declarations
\newcommand{\numarray}{numarray}
\newcommand{\Numarray}{Numarray}  % Only beginning of sentence, otherwise use \numarray
\newcommand{\NUMARRAY}{NumArray}
\newcommand{\numpy}{Numeric}
\newcommand{\NUMPY}{Numerical Python}
\newcommand{\python}{Python}


% mark internal comments
% for any published version switch to the second (empty) definition of the macro!
% \newcommand{\remark}[1]{(\textbf{Note to authors: #1})}
\newcommand{\remark}[1]{}


\title{Numarray\\An Open Source project}

\author{Perry Greenfield \\
   Todd Miller \\
   Rick White \\
   J.C. Hsu \\
   Paul Barrett \\
   Jochen Küpper \\
   Peter J. Verveer \\[1ex]
   Previously authored by: \\
   David Ascher \\
   Paul F. Dubois \\
   Konrad Hinsen \\
   Jim Hugunin \\
   Travis Oliphant \\[1ex]
   with contributions from the Numerical Python community}

\authoraddress{Space Telescope Science Institute, 3700 San Martin Dr,
   Baltimore, MD 21218 \\ UCRL-MA-128569}

% I use date to indicate the manual-updates,
% release below gives the matching software version.
\date{September 10, 2004}       % update before release!
                                % Use an explicit date so that reformatting
                                % doesn't cause a new date to be used.  Setting
                                % the date to \today can be used during draft
                                % stages to make it easier to handle versions.

\release{1.1}                 % (software) release version;
\setshortversion{1.1}         % this is used to define the \version macro

\makeindex                      % tell \index to actually write the .idx file



\begin{document}

\maketitle

% This makes the contents more accessible from the front page of the HTML.
\ifhtml
\part*{General}
\chapter*{Front Matter}
\label{front}
\fi

\input{copyright}



\tableofcontents


\part{Numerical Python}

\NUMARRAY{} (``\numarray{}'') adds a fast multidimensional array facility to
Python.  This part contains all you need to know about ``\numarray{}'' arrays
and the functions that operate upon them.

\label{part:numerical-python}

\declaremodule{extension}{numarray}
\moduleauthor{The numarray team}{numpy@lists.sourceforge.net}
\modulesynopsis{Numerics}

\input{introduction}
\input{installation}
\input{overview}
\input{arraybasics}
\input{ufuncs}
\input{pseudoindices}
\input{arrayfunctions}
\input{arraymethods}
\input{arrayattributes}
\input{chararray}
\input{recordarray}
\input{objectarray}
\input{extending}



\part{Extension modules}

\label{part:numarray-extensions}

\input{convolve}
\input{fft}
\input{linearalgebra}
\input{ma}
\input{mlab}
\input{randomarray}
\input{ndimage}
\input{memmap}

\appendix
\part*{Appendix}
%begin{latexonly}
\makeatletter
\py@reset
\makeatother
%end{latexonly}

\input{glossary}
\input{numarray.ind}

\end{document}


%% Local Variables:
%% mode: LaTeX
%% mode: auto-fill
%% fill-column: 79
%% indent-tabs-mode: nil
%% ispell-dictionary: "american"
%% reftex-fref-is-default: nil
%% TeX-auto-save: t
%% TeX-parse-self: t
%% End:
