tpool -
Part of the Tcl threading extension implementing pools of worker threads.
package require Thread ?2.5?
tpool::create ?options?
tpool::post tpoolId script
tpool::wait tpoolId jobIdList ?varName?
tpool::get tpoolId jobId
tpool::names
tpool::preserve tpoolId
tpool::release tpoolId
-
tpool::create ?options?
- This command creates new threadpool. It accepts several options as
key-value pairs. Options are used to tune some threadpool parameters.
The command returns the ID of the newly created threadpool.
Following options are supported:
- -minthreads number
- Minimum number of threads needed for this threadpool instance.
During threadpool creation, the implementation will create somany
worker threads upfront and will keep at least number of them alive
during the lifetime of the threadpool instance.
Default value of this parameter is 0 (zero). which means that a newly
threadpool will have no worker threads initialy. All worker threads will be
started on demand by callers running tpool::post command and
posting jobs to the job queue.
- -maxthreads number
- Maximum number of threads allowed for this threadpool instance.
If a new job is pending and there are no idle worker threads available,
the implementation will try to create new worker thread. If the number of
available worker threads is lower than the number,
new worker thread will start and the caller will enter event loop and
wait until the worker thread has initialized. If. however, the
number of available worker threads is equal to number, the caller
will enter the event loop and wait for the first worker thread to get idle,
thus ready to run the job.
Default value of this parameter is 4 (four), which means that the
threadpool instance will allow maximum of 4 worker threads running jobs
or being idle waiting for new jobs to get posted to the job queue.
- -idletime seconds
- Time in seconds an idle worker thread waits for the job
to get posted to the job queue. If no job arrives during this interval
and the time expires, the worker thread will check the number of
currently available worker threads. If the number is higher than the
number set by the minthreads option, it will exit.
If an exitscript has been defined, the exiting worker thread
will first run the script and then exit. Errors from the exit script,
if any, are ignored.
The idle worker thread is not servicing the event loop. If you, however,
put the worker thread into the event loop, by evaluating the
vwait or other related Tcl commands, the worker thread
will not be in the idle state, hence the idle timer will not be
taken into account.
Default value for this option is zero (0), meaning that no idle time
is set. Worker threads will thus, once started, never exit.
- -initcmd script
- Tcl script used to initialize new worker thread. This is usually used
to load packages and commands in the worker, set default variables, create
namespaces, and such. If the -initcmd script runs in Tcl error,
the worker will not be created and the initiating command (either the
tpool::create or tpool::post) will throw the
error.
Default value for this option is unspecified, hence, the Tcl interpreter of
the worker thread will contain just the initial set of Tcl commands.
- -exitcmd script
- Tcl script run when the idle worker thread exits. This is normaly used
to cleanup the state of the worker thread, release reserved resources and
cleanup memory.
Default value for this option is unspecified, thus no Tcl script will run on
the worker thread exit.
-
tpool::post tpoolId script
- This command sends a script to the target tpoolId threadpool
for execution. The script will be executed in the first available idle worker thread.
If there are no idle worker threads available, the command will create
new one, enter the event loop and service events until the newly created
thread is initialized. If the current number of worker threads is equal to
the maximum number of worker threads, as defined during the threadpool creation
with the tpool::create command, the command will enter the event loop
and service events while waiting for one of the worker threads to become idle.
The command returns the ID of the posted job. This ID is used for subsequent
tpool::wait and tpool::get commands to wait for and
retrieve result of the posted script respectively. If the threadpool tpoolId
is not found in the list of active thread pools, the command will throw error.
The error will also be triggered if the newly created worker thread fails to
initialize.
-
tpool::wait tpoolId jobIdList ?varName?
- This command waits for one or many jobs, whose job IDs are given in the
jobIdList to get processed by the worker thread(s). If none of the
specified jobs are ready, the command will enter the event loop, service
events and wait for the first job to get ready.
The command returns the list of completed job IDs. If the optional variable
varName is given, it will be set to the list of jobs in the jobIdList
which are still pending. If the threadpool tpoolId is not found in the
list of active thread pools, the command will throw error.
-
tpool::get tpoolId jobId
- This command retrieves the result of the previously posted job jobId.
Only results of jobs waited upon with the tpool::wait command can
be retrieved. If the execution of the script resulted in error, the command
will throw the error and update the errorInfo and errorCode
variables correspondingly. If the pool tpoolId is not found in the list
of threadpools, the command will throw error. If the job jobId
is not ready for retrieval, because it is currently being executed by the worker
thread, the command will throw error.
- tpool::names
- This command returns a list of IDs of threadpools created with the
tpool::create command. If no threadpools were found, the
command will return empty list.
-
tpool::preserve tpoolId
- Each call to this command increments the reference counter of the
threadpool tpoolId by one (1). Command returns the value of the
reference counter after the increment.
With reference counting, one can implement controlled access to a shared
threadpool resource. By incrementing the reference counter, the caller
signalizes that he/she wishes to use the resource for a longer period of time.
By decrementing the counter, using the tpool::release command,
caller signalizes that he/she has finished using the resource.
-
tpool::release tpoolId
- Each call to this command decrements the reference counter of the
threadpool tpoolId by one (1).Command returns the value of the
reference counter after the decrement. When the reference counter reaches
zero (0), the threadpool tpoolId is marked for termination.
You should not reference the threadpool after the tpool::release
command returns zero. The tpoolId handle goes out of scope and
should not be used any more. Any following reference to the same threadpool
handle will result in Tcl error.
Threadpool is one of the most common threading paradigm when it comes
to server applications handling a large number of relatively small tasks.
A very simplistic model for building a server application would be to
create a new thread each time a request arrives and service the request
in the new thread. One of the disadvantages of this approach is that
the overhead of creating a new thread for each request is significant;
a server that created a new thread for each request would spend more time
and consume more system resources in creating and destroying threads than
in processing actual user requests. In addition to the overhead of
creating and destroying threads, active threads consume system resources.
Creating too many threads can cause the system to run out of memory or
trash due to excessive memory consumption.
A thread pool offers a solution to both the problem of thread life-cycle
overhead and the problem of resource trashing. By reusing threads for
multiple tasks, the thread-creation overhead is spread over many tasks.
As a bonus, because the thread already exists when a request arrives,
the delay introduced by thread creation is eliminated. Thus, the request
can be serviced immediately. Furthermore, by properly tuning the number
of threads in the thread pool, resource thrashing may also be eliminated
by forcing any request to wait until a thread is available to process it.
Guide to the Tcl threading model
threads, pool