1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
|
#!/bin/sh
# Author: Marco Ziech (mmz@gmx.net)
# Date: Jan-24-2000
#
# Bnetd UDP masquerade for Linux
#
# NOTE:
# This script is not needed if you have "loose UDP" turned
# on. It was a patch around the 2.2 series. It automates
# all of this for any "well behaved" peer-to-peer games,
# not just for Battle.net clients.
#
# Kernel:
# This script should work fine with 2.2 kernels but I don't
# know if it works with older kernels too.
#
# Installation:
# Copy this file into your local init.d directory.
# The position of this directory may vary with diffrent
# linux distributions.
# On Debian/GNU Linux it's /etc/init.d
# On S.u.S.E. Linux it's /sbin/init.d (I guess)
# To start the script on system startup you have to
# make a symlink to this file from a filename like
# "S99bnetmasq.sh" in the rc2.d directory. To stop it
# on system shutdown do the same with "K01bnetmasq.sh"
# in the rc0.d, rc1.d and rc6.d directories. These
# directories are usually in the same as the init.d
# directory.
# If you have a dial-up connection and want to start the
# script on dial-in you have to put a script which starts
# or stops this script in /etc/ppp/ip-up.d and
# /etc/ppp/ip-down.d .
#
# Using on original Bnet:
# This script should also work with the original Battle.net.
#
# Using on servers not running on your masquerading gateway:
# Outside servers like the real Battle.net will not
# know your correct address, only your internal IP:port.
# to fix it, either bnproxy needs to be improved to
# be used instead of ipmasq or this need to do some
# content altering like with the ftp script.
# --- Thanks to Ross Combs for these corrections.
# This is the destination port on the clients. It is usually 6112.
BNET_PORT=6112
# This is the list of the destination hosts with their ports on
# the firewall. The list should look like this:
# client1IP:GW1port client2IP:GW2port ... clientNIP:GWNport
# Remember that each port can only be allocated by one client.
# Some ports may already be reserved by some programs.
# I recomment using ports between 5000 and 7000. See
# /etc/services on information about assigned ports.
REDIR_LIST="192.168.1.1:5000 192.168.1.2:5001"
# This is the external interface i.e. the interface which is
# connected to the Internet. On dial-up links this is usually
# ppp0 or ippp0 (for ISDN).
EXTERNAL_IF=eth0
# ------------------- END OF CONFIG SECTION -----------------
# This determines the ip of the external interface
EXTERNAL_IP=`LANGUAGE="C" LC_ALL="C" ifconfig $EXTERNAL_IF | grep 'inet addr:' | sed 's/.*inet addr:\([0-9.]*\).*/\1/g'`
case "$1" in
start)
echo -n "Starting bnet masquerading: "
for i in $REDIR_LIST; do
echo -n "$i "
D_HOST="`echo $i | sed -e 's/:/ /g' | awk '{ print $1 }'`"
D_PORT="`echo $i | sed -e 's/:/ /g' | awk '{ print $2 }'`"
ipmasqadm portfw -a -P udp -L $EXTERNAL_IP $D_PORT -R $D_HOST $BNET_PORT
# FIXME: according to: http://www.mail-archive.com/masq@tori.indyramp.com/msg01538.html
#> setting up a single machine would look like:
#> # ipmasqadm portfw -a -P tcp -L $1 6112 -R $2 6112
#> # ipmasqadm portfw -a -P tcp -L $3 6112 -R $2 6112
#> # ipmasqadm portfw -a -P udp -L $1 6112 -R $2 6112
#> # ipmasqadm portfw -a -P udp -L $3 6112 -R $2 6112
#> Replace $1 with the internal IP address of your gateway machine, $2
#> with the address (internal again, but it should be the only) of the
#> machine you're playing starcraft on and $3 with the external IP ad-
#> dress of the gateway machine.
# This implies that
# inside_gw --> client
# outside_gw --> inside_gw
# this script doesn't do the gw --> gw setup.... does it need to?!
done
echo "."
;;
stop)
echo -n "Stopping bnet masquerading: "
for i in $REDIR_LIST; do
echo -n "$i "
D_PORT="`echo $i | sed -e 's/:/ /g' | awk '{ print $2 }'`"
ipmasqadm portfw -d -P udp -L $EXTERNAL_IP $D_PORT
done
echo "."
;;
*)
echo "Usage: $0 {start|stop}"
exit 1
;;
esac
|
