btrfs(5)
========

DESCRIPTION
-----------

This document describes topics related to BTRFS that are not specific to the
tools.  Currently covers:

#. mount options
#. filesystem features
#. checksum algorithms
#. compression
#. sysfs interface
#. filesystem exclusive operations
#. filesystem limits
#. bootloader support
#. file attributes
#. zoned mode
#. control device
#. filesystems with multiple block group profiles
#. seeding device
#. RAID56 status and recommended practices
#. glossary
#. storage model, hardware considerations

.. _man-btrfs5-mount-options:

MOUNT OPTIONS
-------------

.. include:: ch-mount-options.rst

.. _man-btrfs5-filesystem-features:

FILESYSTEM FEATURES
-------------------

The basic set of filesystem features gets extended over time. The backward
compatibility is maintained and the features are optional, need to be
explicitly asked for so accidental use will not create incompatibilities.

There are several classes and the respective tools to manage the features:

at mkfs time only
        This is namely for core structures, like the b-tree nodesize or checksum
        algorithm, see :doc:`mkfs.btrfs` for more details.

after mkfs, on an unmounted filesystem
        Features that may optimize internal structures or add new structures to support
        new functionality, see :doc:`btrfstune`. The command
        :command:`btrfs inspect-internal dump-super /dev/sdx`
        will dump a superblock, you can map the value of
        *incompat_flags* to the features listed below

after mkfs, on a mounted filesystem
        The features of a filesystem (with a given UUID) are listed in
        :file:`/sys/fs/btrfs/UUID/features/`, one file per feature. The status is stored
        inside the file. The value *1* is for enabled and active, while *0* means the
        feature was enabled at mount time but turned off afterwards.

        Whether a particular feature can be turned on a mounted filesystem can be found
        in the directory :file:`/sys/fs/btrfs/features/`, one file per feature. The value *1*
        means the feature can be enabled.

List of features (see also :doc:`mkfs.btrfs` section
:ref:`FILESYSTEM FEATURES<man-mkfs-filesystem-features>`):

big_metadata
        (since: 3.4)

        the filesystem uses *nodesize* for metadata blocks, this can be bigger than the
        page size

block_group_tree
        (since: 6.1)

        block group item representation using a dedicated b-tree, this can greatly
        reduce mount time for large filesystems

compress_lzo
        (since: 2.6.38)

        the *lzo* compression has been used on the filesystem, either as a mount option
        or via :command:`btrfs filesystem defrag`.

compress_zstd
        (since: 4.14)

        the *zstd* compression has been used on the filesystem, either as a mount option
        or via :command:`btrfs filesystem defrag`.

default_subvol
        (since: 2.6.34)

        the default subvolume has been set on the filesystem

extended_iref
        (since: 3.7)

        increased hardlink limit per file in a directory to 65536, older kernels
        supported a varying number of hardlinks depending on the sum of all file name
        sizes that can be stored into one metadata block

free_space_tree
        (since: 4.5)

        free space representation using a dedicated b-tree, successor of v1 space cache

metadata_uuid
        (since: 5.0)

        the main filesystem UUID is the metadata_uuid, which stores the new UUID only
        in the superblock while all metadata blocks still have the UUID set at mkfs
        time, see :doc:`btrfstune` for more

mixed_backref
        (since: 2.6.31)

        the last major disk format change, improved backreferences, now default

mixed_groups
        (since: 2.6.37)

        mixed data and metadata block groups, i.e. the data and metadata are not
        separated and occupy the same block groups, this mode is suitable for small
        volumes as there are no constraints how the remaining space should be used
        (compared to the split mode, where empty metadata space cannot be used for data
        and vice versa)

        on the other hand, the final layout is quite unpredictable and possibly highly
        fragmented, which means worse performance

no_holes
        (since: 3.14)

        improved representation of file extents where holes are not explicitly
        stored as an extent, saves a few percent of metadata if sparse files are used

raid1c34
        (since: 5.5)

        extended RAID1 mode with copies on 3 or 4 devices respectively

raid_stripe_tree
        (since: 6.7)

        a separate tree for tracking file extents on RAID profiles

RAID56
        (since: 3.9)

        the filesystem contains or contained a RAID56 profile of block groups

rmdir_subvol
        (since: 4.18)

        indicate that :manref:`rmdir(2)` syscall can delete an empty subvolume just like an
        ordinary directory. Note that this feature only depends on the kernel version.

skinny_metadata
        (since: 3.10)

        reduced-size metadata for extent references, saves a few percent of metadata

send_stream_version
        (since: 5.10)

        number of the highest supported send stream version

simple_quota
        (since: 6.7)

        simplified quota accounting

supported_checksums
        (since: 5.5)

        list of checksum algorithms supported by the kernel module, the respective
        modules or built-in implementing the algorithms need to be present to mount
        the filesystem, see section :ref:`CHECKSUM ALGORITHMS<man-mkfs-checksum-algorithms>`.

supported_sectorsizes
        (since: 5.13)

        list of values that are accepted as sector sizes (:command:`mkfs.btrfs --sectorsize`) by
        the running kernel

supported_rescue_options
        (since: 5.11)

        list of values for the mount option *rescue* that are supported by the running
        kernel, see :doc:`btrfs-man5`

zoned
        (since: 5.12)

        zoned mode is allocation/write friendly to host-managed zoned devices,
        allocation space is partitioned into fixed-size zones that must be updated
        sequentially, see section :ref:`ZONED MODE<man-btrfs5-zoned-mode>`

SWAPFILE SUPPORT
----------------

.. include:: ch-swapfile.rst

.. _man-mkfs-checksum-algorithms:

CHECKSUM ALGORITHMS
-------------------

.. include:: ch-checksumming.rst

COMPRESSION
-----------

.. include:: ch-compression.rst

SYSFS INTERFACE
---------------

.. include:: ch-sysfs.rst

.. _man-btrfs5-filesystem-exclusive-operations:

FILESYSTEM EXCLUSIVE OPERATIONS
-------------------------------

There are several operations that affect the whole filesystem and cannot be run
in parallel. Attempt to start one while another is running will fail (see
exceptions below).

Since kernel 5.10 the currently running operation can be obtained from
:file:`/sys/fs/UUID/exclusive_operation` with following values and operations:

* balance
* balance paused (since 5.17)
* device add
* device delete
* device replace
* resize
* swapfile activate
* none

Enqueuing is supported for several btrfs subcommands so they can be started
at once and then serialized.

There's an exception when a paused balance allows to start a device add
operation as they don't really collide and this can be used to add more space
for the balance to finish.

FILESYSTEM LIMITS
-----------------

.. include:: ch-fs-limits.rst

BOOTLOADER SUPPORT
------------------

.. include:: ch-bootloaders.rst

FILE ATTRIBUTES
---------------

.. include:: ch-file-attributes.rst

.. _man-btrfs5-zoned-mode:

ZONED MODE
----------

.. include:: ch-zoned-intro.rst


CONTROL DEVICE
--------------

There's a character special device :file:`/dev/btrfs-control` with major and minor
numbers 10 and 234 (the device can be found under the *misc* category).

.. code-block:: none

        $ ls -l /dev/btrfs-control
        crw------- 1 root root 10, 234 Jan  1 12:00 /dev/btrfs-control

The device accepts some ioctl calls that can perform following actions on the
filesystem module:

* scan devices for btrfs filesystem (i.e. to let multi-device filesystems mount
  automatically) and register them with the kernel module
* similar to scan, but also wait until the device scanning process is finished
  for a given filesystem
* get the supported features (can be also found under :file:`/sys/fs/btrfs/features`)

The device is created when btrfs is initialized, either as a module or a
built-in functionality and makes sense only in connection with that. Running
e.g. mkfs without the module loaded will not register the device and will
probably warn about that.

In rare cases when the module is loaded but the device is not present (most
likely accidentally deleted), it's possible to recreate it by

.. code-block:: bash

        # mknod --mode=600 /dev/btrfs-control c 10 234

or (since 5.11) by a convenience command

.. code-block:: bash

        # btrfs rescue create-control-device

The control device is not strictly required but the device scanning will not
work and a workaround would need to be used to mount a multi-device filesystem.
The mount option *device* can trigger the device scanning during mount, see
also :command:`btrfs device scan`.

.. _man-btrfs5-filesystem-with-multiple-profiles:

FILESYSTEM WITH MULTIPLE PROFILES
---------------------------------

It is possible that a btrfs filesystem contains multiple block group profiles
of the same type.  This could happen when a profile conversion using balance
filters is interrupted (see :doc:`btrfs-balance`).  Some
:command:`btrfs` commands perform
a test to detect this kind of condition and print a warning like this:

.. code-block:: none

        WARNING: Multiple block group profiles detected, see 'man btrfs(5)'.
        WARNING:   Data: single, raid1
        WARNING:   Metadata: single, raid1

The corresponding output of :command:`btrfs filesystem df` might look like:

.. code-block:: none

        WARNING: Multiple block group profiles detected, see 'man btrfs(5)'.
        WARNING:   Data: single, raid1
        WARNING:   Metadata: single, raid1
        Data, RAID1: total=832.00MiB, used=0.00B
        Data, single: total=1.63GiB, used=0.00B
        System, single: total=4.00MiB, used=16.00KiB
        Metadata, single: total=8.00MiB, used=112.00KiB
        Metadata, RAID1: total=64.00MiB, used=32.00KiB
        GlobalReserve, single: total=16.25MiB, used=0.00B

There's more than one line for type *Data* and *Metadata*, while the profiles
are *single* and *RAID1*.

This state of the filesystem OK but most likely needs the user/administrator to
take an action and finish the interrupted tasks. This cannot be easily done
automatically, also the user knows the expected final profiles.

In the example above, the filesystem started as a single device and *single*
block group profile. Then another device was added, followed by balance with
*convert=raid1* but for some reason hasn't finished. Restarting the balance
with *convert=raid1* will continue and end up with filesystem with all block
group profiles *RAID1*.

.. note::
        If you're familiar with balance filters, you can use
        *convert=raid1,profiles=single,soft*, which will take only the unconverted
        *single* profiles and convert them to *raid1*. This may speed up the conversion
        as it would not try to rewrite the already convert *raid1* profiles.

Having just one profile is desired as this also clearly defines the profile of
newly allocated block groups, otherwise this depends on internal allocation
policy. When there are multiple profiles present, the order of selection is
RAID56, RAID10, RAID1, RAID0 as long as the device number constraints are
satisfied.

Commands that print the warning were chosen so they're brought to user
attention when the filesystem state is being changed in that regard. This is:
:command:`device add`, :command:`device delete`, :command:`balance cancel`, :command:`balance pause`. Commands
that report space usage: :command:`filesystem df`, :command:`device usage`. The command
:command:`filesystem usage` provides a line in the overall summary:

.. code-block:: none

    Multiple profiles:                 yes (data, metadata)

.. _man-btrfs5-seeding-device:

SEEDING DEVICE
--------------

.. include:: ch-seeding-device.rst

RAID56 STATUS AND RECOMMENDED PRACTICES
---------------------------------------

The RAID56 feature provides striping and parity over several devices, same as
the traditional RAID5/6. There are some implementation and design deficiencies
that make it unreliable for some corner cases and the feature **should not be
used in production, only for evaluation or testing**.  The power failure safety
for metadata with RAID56 is not 100%.

Metadata
^^^^^^^^

Do not use *raid5* nor *raid6* for metadata. Use *raid1* or *raid1c3*
respectively.

The substitute profiles provide the same guarantees against loss of 1 or 2
devices, and in some respect can be an improvement.  Recovering from one
missing device will only need to access the remaining 1st or 2nd copy, that in
general may be stored on some other devices due to the way RAID1 works on
btrfs, unlike on a striped profile (similar to *raid0*) that would need all
devices all the time.

The space allocation pattern and consumption is different (e.g. on N devices):
for *raid5* as an example, a 1GiB chunk is reserved on each device, while with
*raid1* there's each 1GiB chunk stored on 2 devices. The consumption of each
1GiB of used metadata is then *N * 1GiB* for vs *2 * 1GiB*. Using *raid1*
is also more convenient for balancing/converting to other profile due to lower
requirement on the available chunk space.

Missing/incomplete support
^^^^^^^^^^^^^^^^^^^^^^^^^^

When RAID56 is on the same filesystem with different raid profiles, the space
reporting is inaccurate, e.g. :command:`df`, :command:`btrfs filesystem df` or
:command:`btrfs filesystem usage`. When there's only a one profile per block
group type (e.g. RAID5 for data) the reporting is accurate.

When scrub is started on a RAID56 filesystem, it's started on all devices that
degrade the performance. The workaround is to start it on each device
separately. Due to that the device stats may not match the actual state and
some errors might get reported multiple times.

The *write hole* problem. An unclean shutdown could leave a partially written
stripe in a state where the some stripe ranges and the parity are from the old
writes and some are new. The information which is which is not tracked. Write
journal is not implemented. Alternatively a full read-modify-write would make
sure that a full stripe is always written, avoiding the write hole completely,
but performance in that case turned out to be too bad for use.

The striping happens on all available devices (at the time the chunks were
allocated), so in case a new device is added it may not be utilized
immediately and would require a rebalance. A fixed configured stripe width is
not implemented.


GLOSSARY
--------

.. include:: ch-glossary.rst


STORAGE MODEL, HARDWARE CONSIDERATIONS
--------------------------------------

.. include:: ch-hardware-considerations.rst

SEE ALSO
--------

:manref:`acl(5)`,
:doc:`btrfs`,
:manref:`chattr(1)`,
:manref:`fstrim(8)`,
:manref:`ioctl(2)`,
:doc:`btrfs-ioctl`,
:doc:`mkfs.btrfs`,
:manref:`mount(8)`,
:manref:`swapon(8)`