1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
/*
* config.h - Configuration options for diald.
*
* Copyright (c) 1994, 1995, 1996 Eric Schenk.
* Copyright (c) 1999 Mike Jagdis.
* All rights reserved. Please see the file LICENSE which should be
* distributed with this software for terms of use.
*
* These are the compile time defaults for various system files.
* You may want to edit these to match your system before you compile diald.
* However, if you didn't, don't panic. Almost all of these locations can be
* configured at run time if necessary. The only thing you can't configure
* at run time is the location of the main diald configuration files.
*
*/
/*
* Diald needs to be able to find its default configuration files.
* These paths should match the installation path in the Makefile!
* THIS MUST BE CONFIGURED AT COMPILE TIME IF YOU WANT TO CHANGE IT!
*/
#define DIALD_CONFIG_FILE "/etc/diald/diald.options"
#define DIALD_DEFS_FILE "/etc/diald/diald.defs"
/*
* The default access to be allowed on monitor connections. Note
* that connections on the control fifo can always do anything
* because there is no way to determine who asked. This only
* applies to TCP monitor connections. The full list of access
* flags can be found in access.h.
* N.B. If ACCESS_CONTROL is not set then *anything* received
* on the pipe is treated as a message and no commands are possible.
* If ACCESS_AUTH is not set then the "auth" command may not
* be used to get other than the default access capabilities.
*/
#define CONFIG_DEFAULT_ACCESS \
(ACCESS_CONTROL | ACCESS_AUTH \
| ACCESS_MONITOR)
#if 0
/* This is not needed. See the TODO file. */
/* The PORT_MASQ_BEGIN and PORT_MASQ_END defines specify the range
* of ports which may be used by the kernel masquerade code under Linux.
* Some sites that need to masquerade many connections at once may have
* increased this range. If so you should change the defines here. For a
* truely general diald you should leave both undefined but this adds some
* usually unnecessary overhead.
* N.B. The demasquerading needs to be enabled using the "demasq" option.
* FIXME: This probably isn't a big killer unless you have lots of
* short lived connections?
*/
#define PORT_MASQ_BEGIN 61000
#define PORT_MASQ_END (PORT_MASQ_BEGIN + 4096)
#endif
/*****************************************************************************
* EVERYTHING BELOW HERE IS RUN TIME CONFIGURABLE
* You can change these things if you want to save yourself some
* entries in your configuration files.
****************************************************************************/
/*
* Your lock files are probably somewhere else unless you
* happen to be running a newer distribution that is compiliant
* the the Linux File System Standard. On older distributions
* you will usually find them in /var/spool/uucp or /usr/spool/uucp.
*/
#define LOCK_PREFIX "/var/lock/LCK.."
/*
* If your lock files should contain binary PID's then
* set the following to 0. I think most linux
* distributions want ASCII PID's in the lock files.
*/
#define PIDSTRING 1
/*
* Define where to put the diald.pid file. Under the FSSTD this
* should be in /var/run, but you're system might have them
* elsewhere. Check and be sure.
*/
#define RUN_PREFIX "/var/run"
/* The following will all be searched for in /sbin:/usr/sbin:/bin:/usr/bin
* so you do not, normally, need to define any of these paths. If you
* have a really strange setup you can either define paths here or
* use the run time path-* options.
*/
#if 0
/*
* Diald needs to use some external binaries to set up
* routing tables and to bring up the proxy device. If
* you do not define the paths here diald will look for
* each program first in /sbin and then in /usr/sbin.
* If you wish to use a specific binary instead of the
* defined or search located binary you may use the path-*
* config options to override them.
*/
#undef PATH_ROUTE "/sbin/route"
#undef PATH_IFCONFIG "/sbin/ifconfig"
/*
* The "ip" program is the preferred way to set routes on Linux 2.2
* and beyond. Either specify the path here or use the "path-ip"
* config option. The "ip" program you use needs to understand
* the "metric" keyword - some older ones do not. You can find
* "ip" on: ftp://ftp.inr.ac.ru/ip-routing/
*/
#undef PATH_IP "/usr/sbin/ip"
/*
* Diald needs to know where to find the bootpc binary in order to
* use the bootp protocol for dynamic slip address determination.
*/
#undef PATH_BOOTPC "/usr/sbin/bootpc"
/*
* If you're never going to use pppd don't worry if this is wrong.
* Otherwise, find your pppd executable and set this path to match its
* location.
*/
#undef PATH_PPPD "/usr/sbin/pppd"
#endif
|
