File: rfc2878.txt

package info (click to toggle)
doc-rfc 20181229-2
  • links: PTS, VCS
  • area: non-free
  • in suites: buster
  • size: 570,944 kB
  • sloc: xml: 285,646; sh: 107; python: 90; perl: 42; makefile: 14
file content (2131 lines) | stat: -rw-r--r-- 79,527 bytes parent folder | download | duplicates (5)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394
1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
1444
1445
1446
1447
1448
1449
1450
1451
1452
1453
1454
1455
1456
1457
1458
1459
1460
1461
1462
1463
1464
1465
1466
1467
1468
1469
1470
1471
1472
1473
1474
1475
1476
1477
1478
1479
1480
1481
1482
1483
1484
1485
1486
1487
1488
1489
1490
1491
1492
1493
1494
1495
1496
1497
1498
1499
1500
1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515
1516
1517
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538
1539
1540
1541
1542
1543
1544
1545
1546
1547
1548
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
1566
1567
1568
1569
1570
1571
1572
1573
1574
1575
1576
1577
1578
1579
1580
1581
1582
1583
1584
1585
1586
1587
1588
1589
1590
1591
1592
1593
1594
1595
1596
1597
1598
1599
1600
1601
1602
1603
1604
1605
1606
1607
1608
1609
1610
1611
1612
1613
1614
1615
1616
1617
1618
1619
1620
1621
1622
1623
1624
1625
1626
1627
1628
1629
1630
1631
1632
1633
1634
1635
1636
1637
1638
1639
1640
1641
1642
1643
1644
1645
1646
1647
1648
1649
1650
1651
1652
1653
1654
1655
1656
1657
1658
1659
1660
1661
1662
1663
1664
1665
1666
1667
1668
1669
1670
1671
1672
1673
1674
1675
1676
1677
1678
1679
1680
1681
1682
1683
1684
1685
1686
1687
1688
1689
1690
1691
1692
1693
1694
1695
1696
1697
1698
1699
1700
1701
1702
1703
1704
1705
1706
1707
1708
1709
1710
1711
1712
1713
1714
1715
1716
1717
1718
1719
1720
1721
1722
1723
1724
1725
1726
1727
1728
1729
1730
1731
1732
1733
1734
1735
1736
1737
1738
1739
1740
1741
1742
1743
1744
1745
1746
1747
1748
1749
1750
1751
1752
1753
1754
1755
1756
1757
1758
1759
1760
1761
1762
1763
1764
1765
1766
1767
1768
1769
1770
1771
1772
1773
1774
1775
1776
1777
1778
1779
1780
1781
1782
1783
1784
1785
1786
1787
1788
1789
1790
1791
1792
1793
1794
1795
1796
1797
1798
1799
1800
1801
1802
1803
1804
1805
1806
1807
1808
1809
1810
1811
1812
1813
1814
1815
1816
1817
1818
1819
1820
1821
1822
1823
1824
1825
1826
1827
1828
1829
1830
1831
1832
1833
1834
1835
1836
1837
1838
1839
1840
1841
1842
1843
1844
1845
1846
1847
1848
1849
1850
1851
1852
1853
1854
1855
1856
1857
1858
1859
1860
1861
1862
1863
1864
1865
1866
1867
1868
1869
1870
1871
1872
1873
1874
1875
1876
1877
1878
1879
1880
1881
1882
1883
1884
1885
1886
1887
1888
1889
1890
1891
1892
1893
1894
1895
1896
1897
1898
1899
1900
1901
1902
1903
1904
1905
1906
1907
1908
1909
1910
1911
1912
1913
1914
1915
1916
1917
1918
1919
1920
1921
1922
1923
1924
1925
1926
1927
1928
1929
1930
1931
1932
1933
1934
1935
1936
1937
1938
1939
1940
1941
1942
1943
1944
1945
1946
1947
1948
1949
1950
1951
1952
1953
1954
1955
1956
1957
1958
1959
1960
1961
1962
1963
1964
1965
1966
1967
1968
1969
1970
1971
1972
1973
1974
1975
1976
1977
1978
1979
1980
1981
1982
1983
1984
1985
1986
1987
1988
1989
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
2025
2026
2027
2028
2029
2030
2031
2032
2033
2034
2035
2036
2037
2038
2039
2040
2041
2042
2043
2044
2045
2046
2047
2048
2049
2050
2051
2052
2053
2054
2055
2056
2057
2058
2059
2060
2061
2062
2063
2064
2065
2066
2067
2068
2069
2070
2071
2072
2073
2074
2075
2076
2077
2078
2079
2080
2081
2082
2083
2084
2085
2086
2087
2088
2089
2090
2091
2092
2093
2094
2095
2096
2097
2098
2099
2100
2101
2102
2103
2104
2105
2106
2107
2108
2109
2110
2111
2112
2113
2114
2115
2116
2117
2118
2119
2120
2121
2122
2123
2124
2125
2126
2127
2128
2129
2130
2131






Network Working Group                                      M. Higashiyama
Request for Comments: 2878                                        Anritsu
Obsoletes: 1638                                                  F. Baker
Category: Standards Track                                           Cisco
                                                                July 2000


                  PPP Bridging Control Protocol (BCP)

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2000).  All Rights Reserved.

Abstract

   The Point-to-Point Protocol (PPP) [6] provides a standard method for
   transporting multi-protocol datagrams over point-to-point links.  PPP
   defines an extensible Link Control Protocol, and proposes a family of
   Network Control Protocols for establishing and configuring different
   network-layer protocols.

   This document defines the Network Control Protocol for establishing
   and configuring Remote Bridging for PPP links.

   This document obsoletes RFC 1638, which was based on the IEEE
   802.1D-1993 MAC Bridge[3]. This document extends that specification
   by including the IEEE 802.1D-1998 MAC Bridge[8] and IEEE 802.1Q
   Virtual LAN (VLAN)[9] standards. This document also improves the
   protocol in order to support high-speed switched LANs.














Higashiyama & Baker         Standards Track                     [Page 1]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


Table of Contents

   1.     Historical Perspective ................................    3
      1.1       Requirements Keywords ...........................    3
   2.     Methods of Bridging ...................................    3
      2.1       Transparent Bridging ............................    3
      2.2       Remote Transparent Bridging .....................    4
      2.3       Source Routing ..................................    5
      2.4       Remote Source Route Bridging ....................    6
      2.5       SR-TB Translational Bridging ....................    7
   3.     Traffic Services ......................................    7
      3.1       LAN Frame Checksum Preservation .................    7
      3.2       Traffic having no LAN Frame Checksum ............    7
      3.3       Tinygram Compression ............................    8
      3.4       Virtual LANs ....................................    8
   4.     A PPP Network Control Protocol for Bridging ...........    9
      4.1       Sending Bridge Frames ...........................   10
         4.1.1  Maximum Receive Unit Considerations .............   11
         4.1.2  Loopback and Link Quality Monitoring ............   11
         4.1.3  Message Sequence ................................   11
         4.1.4  Separation of Spanning Tree Domains .............   12
      4.2       Bridged LAN Traffic in IEEE 802 Untagged Frame ..   12
      4.3       Bridged LAN Traffic in IEEE 802 Tagged Frame ....   16
      4.4       Bridge management protocol data unit ............   21
   5.     BCP Configuration Options .............................   21
      5.1       Bridge-Identification ...........................   22
      5.2       Line-Identification .............................   23
      5.3       MAC-Support .....................................   25
      5.4       Tinygram-Compression ............................   26
      5.5       MAC-Address .....................................   27
      5.6       Spanning Tree Protocol (old formatted) ..........   28
      5.7       IEEE-802-Tagged-Frame ...........................   30
      5.8       Management-Inline ...............................   30
   6.     Changes From RFC 1638 .................................   31
   7.     Security Considerations ...............................   32
   8.     Intellectual Property Notice ..........................   32
   9.     IANA Considerations ...................................   33
   10.    Acknowledgments .......................................   33
   APPENDICES ...................................................   34
      A.     Spanning Tree Bridge PDU (old formatted) ...........   34
      B.     Tinygram-Compression Pseudo-Code ...................   35
   References ...................................................   36
   Authors' Addresses ...........................................   37
   Full Copyright Statement......................................   38







Higashiyama & Baker         Standards Track                     [Page 2]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


1.  Historical Perspective

   Two basic algorithms are ambient in the industry for Bridging of
   Local Area Networks.  The more common algorithm is called
   "Transparent Bridging", and has been standardized for Extended LAN
   configurations by IEEE 802.1.  The other is called "Source Route
   Bridging", and is prevalent on IEEE 802.5 Token Ring LANs.

   The IEEE has combined these two methods into a device called a Source
   Routing Transparent (SRT) bridge, which concurrently provides both
   Source Route and Transparent bridging.  Transparent and SRT bridges
   are specified in IEEE standard 802.1D-1998 [8].

   Although IEEE committee 802.1G is addressing remote bridging [2],
   neither standard directly defines the mechanisms for implementing
   remote bridging.  Technically, that would be beyond the IEEE 802
   committee's charter.  However, both 802.1D and 802.1G allow for it.
   The implementor may model the line either as a component within a
   single MAC Relay Entity, or as the LAN media between two remote
   bridges.

   The original IEEE 802.1D is augmented by IEEE 802.1Q [9] to provide
   support for Virtual LAN. Virtual LAN is an integral feature of
   switched LAN networks.

1.1 Requirements Keywords

   The keywords MUST, MUST NOT, REQUIRED, SHALL, SHALL NOT, SHOULD,
   SHOULD NOT, RECOMMENDED, MAY, and OPTIONAL, when they appear in this
   document, are to be interpreted as described in [12].

2.  Methods of Bridging

2.1.  Transparent Bridging

   As a favor to the uninitiated, let us first describe Transparent
   Bridging.  Essentially, the bridges in a network operate as isolated
   entities, largely unaware of each others' presence.  A Transparent
   Bridge maintains a Forwarding Database consisting of

                        {address, interface}

                               or

                      {address, interface, VLAN ID}






Higashiyama & Baker         Standards Track                     [Page 3]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   records, by saving the Source Address of each LAN transmission that
   it receives, along with the interface identifier for the interface it
   was received on.  Bridges which support Virtual LANs additionally
   keep the Virtual LAN ID in their forwarding database. It goes on to
   check whether the Destination Address is in the database, and if so,
   either discards the message when the destination and source are
   located at the same interface, or forwards the message to the
   indicated interface.  A message whose Destination Address is not
   found in the table is forwarded to all interfaces except the one it
   was received on.  This behavior applies to Broadcast/Multicast frames
   as well.

   The obvious fly in the ointment is that redundant paths in the
   network cause indeterminate (nay, all too determinate) forwarding
   behavior to occur.  To prevent this, a protocol called the Spanning
   Tree Protocol is executed between the bridges to detect and logically
   remove redundant paths from the network.

   One system is elected as the "Root", which periodically emits a
   message called a Bridge Protocol Data Unit (BPDU), heard by all of
   its neighboring bridges.  Each of these modifies and passes the BPDU
   on to its neighbors, until it arrives at the leaf LAN segments in the
   network (where it dies, having no further neighbors to pass it
   along), or until the message is stopped by a bridge which has a
   superior path to the "Root".  In this latter case, the interface the
   BPDU was received on is ignored (it is placed in a Hot Standby
   status, no traffic is emitted onto it except the BPDU, and all
   traffic received from it is discarded), until a topology change
   forces a recalculation of the network.

   To establish Virtual LANs in an environment of multiple bridges, GVRP
   (GARP VLAN Registration Protocol) is executed between bridges to
   exchange Virtual LAN information. GVRP provides a mechanism to
   dynamically establish and update their knowledge of the set of
   Virtual LANs that currently have active members.

   To reduce unnecessary multicast flooding in the network, bridges
   exchange group MAC addresses using the GARP Multicast Registration
   Protocol. GMRP provides a mechanism so that bridges can know which
   multicast frames should be forwarded on each port.

2.2.  Remote Transparent Bridging

   There exist two basic sorts of bridges -- those that interconnect
   LANs directly, called Local Bridges, and those that interconnect LANs
   via an intermediate medium such as a leased line, called Remote
   Bridges.  PPP may be used to connect Remote Bridges.




Higashiyama & Baker         Standards Track                     [Page 4]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   The IEEE 802.1G Remote MAC Bridging committee has proposed a model of
   a Remote Bridge in which a set of two or more Remote Bridges that are
   interconnected via remote lines are termed a Remote Bridge Group.
   Within a Group, a Remote Bridge Cluster is dynamically formed through
   execution of the spanning tree as the set of bridges that may pass
   frames among each other.

   This model bestows on the remote lines the basic properties of a LAN,
   but does not require a one-to-one mapping of lines to virtual LAN
   segments.  For instance, the model of three interconnected Remote
   Bridges, A, B and C, may be that of a virtual LAN segment between A
   and B and another between B and C.  However, if a line exists between
   Remote Bridges B and C, a frame could actually be sent directly from
   B to C, as long as there was the external appearance that it had
   travelled through A.

   IEEE 802.1G thus allows for a great deal of implementation freedom
   for features such as route optimization and load balancing, as long
   as the model is maintained.

   For simplicity, we discuss Remote Bridging in this document in terms
   of two Remote Bridges connected by a single line.

2.3.  Source Routing

   The IEEE 802.1D Committee has standardized Source Routing for any MAC
   Type that allows its use.  Currently, MAC Types that support Source
   Routing are FDDI and IEEE 802.5 Token Ring.

   The IEEE standard defines Source Routing only as a component of an
   SRT bridge.  However, many bridges have been implemented which are
   capable of performing Source Routing alone.  These are most commonly
   implemented in accordance either with the IBM Token-Ring Network
   Architecture Reference [1] or with the Source Routing Appendix of
   IEEE 802.1D-1998 [8].

   In the Source Routing approach, the originating system has the
   responsibility of indicating the path that the message should follow.
   It does this, if the message is directed off of the local segment, by
   including a variable length MAC header extension called the Routing
   Information Field (RIF).  The RIF consists of one 16-bit word of
   flags and parameters, followed by zero or more segment-and-bridge
   identifiers.  Each bridge en route determines from this source route
   list whether it should accept the message and how to forward it.

   In order to discover the path to a destination, the originating
   system transmits an Explorer frame.  An All-Routes Explorer (ARE)
   frame follows all possible paths to a destination.  A Spanning Tree



Higashiyama & Baker         Standards Track                     [Page 5]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   Explorer (STE) frame follows only those paths defined by Bridge ports
   that the Spanning Tree Algorithm has put in Forwarding state.  Port
   states do not apply to ARE or Specifically-Routed Frames.  The
   destination system replies to each copy of an ARE frame with a
   Specifically-Routed Frame, and to an STE frame with an ARE frame.  In
   either case, the originating station may receive multiple replies,
   from which it chooses the route it will use for future Specifically-
   Routed Frames.

   The algorithm for Source Routing requires the bridge to be able to
   identify any interface by its segment-and-bridge identifier.  When a
   packet is received that has the RIF present, a boolean in the RIF is
   inspected to determine whether the segment-and-bridge identifiers are
   to be inspected in "forward" or "reverse" sense.  In its search, the
   bridge looks for the segment-and-bridge identifier of the interface
   the packet was received on, and forwards the packet toward the
   segment identified in the segment-and-bridge identifier that follows
   it.

   GVRP and GMRP are available and effective on Source Routing networks.

2.4.  Remote Source Route Bridging

   There is no Remote Source Route Bridge proposal in IEEE 802.1 at this
   time, although many vendors ship remote Source Routing Bridges.

   We allow for modelling the line either as a connection residing
   between two halves of a "split" Bridge (the split-bridge model), or
   as a LAN segment between two Bridges (the independent-bridge model).
   In the latter case, the line requires a LAN Segment ID.

   By default, PPP Source Route Bridges use the independent-bridge
   model.  This requirement ensures interoperability in the absence of
   option negotiation.  In order to use the split-bridge model, a system
   MUST successfully negotiate the Bridge-Identification Configuration
   Option.

   Although no option negotiation is required for a system to use the
   independent-bridge model, it is strongly recommended that systems
   using this model negotiate the Line-Identification Configuration
   Option.  Doing so will verify correct configuration of the LAN
   Segment Id assigned to the line.

   When two PPP systems use the split-bridge model, the system that
   transmits an Explorer frame onto the PPP link MUST update the RIF on
   behalf of the two systems.  The purpose of this constraint is to
   ensure interoperability and to preserve the simplicity of the
   bridging algorithm.  For example, if the receiving system did not



Higashiyama & Baker         Standards Track                     [Page 6]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   know whether the transmitting system had updated the RIF, it would
   have to scan the RIF and decide whether to update it.  The choice of
   the transmitting system for the role of updating the RIF allows the
   system receiving the frame from the PPP link to forward the frame
   without processing the RIF.

   Given that source routing is configured on a line or set of lines,
   the specifics of the link state with respect to STE frames are
   defined by the Spanning Tree Protocol in use.  Choice of the split-
   bridge or independent-bridge model does not affect spanning tree
   operation.  In both cases, the spanning tree protocol is executed on
   the two systems independently.

2.5.  SR-TB Translational Bridging

   IEEE 802 is not currently addressing bridges that translate between
   Transparent Bridging and Source Routing.  For the purposes of this
   standard, such a device is either a Transparent or a Source Routing
   bridge, and will act on the line in one of these two ways, just as it
   does on the LAN.

3.  Traffic Services

   Several services are provided for the benefit of different system
   types and user configurations.  These include LAN Frame Checksum
   Preservation, LAN Frame Checksum Generation, Tinygram Compression,
   and the identification of closed sets of LANs.

3.1.  LAN Frame Checksum Preservation

   IEEE 802.1 stipulates that the Extended LAN must enjoy the same
   probability of undetected error that an individual LAN enjoys.
   Although there has been considerable debate concerning the algorithm,
   no other algorithm has been proposed than having the LAN Frame
   Checksum received by the ultimate receiver be the same value
   calculated by the original transmitter.  Achieving this requires, of
   course, that the line protocols preserve the LAN Frame Checksum from
   end to end.  The protocol is optimized towards this approach.

3.2.  Traffic having no LAN Frame Checksum

   The fact that the protocol is optimized towards LAN Frame Checksum
   preservation raises twin questions: "What is the approach to be used
   by systems which, for whatever reason, cannot easily support Frame
   Checksum preservation?" and "What is the approach to be used when the
   system originates a message, which therefore has no Frame Checksum
   precalculated?".




Higashiyama & Baker         Standards Track                     [Page 7]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   Surely, one approach would be to require stations to calculate the
   Frame Checksum in software if hardware support were unavailable; this
   would meet with profound dismay, and would raise serious questions of
   interpretation in a Bridge/Router.

   However, stations which implement LAN Frame Checksum preservation
   must already solve this problem, as they do originate traffic.
   Therefore, the solution adopted is that messages which have no Frame
   Checksum are tagged and carried across the line.

   When a system which does not implement LAN Frame Checksum
   preservation receives a frame having an embedded FCS, it converts it
   for its own use by removing the trailing four octets.  When any
   system forwards a frame which contains no embedded FCS to a LAN, it
   forwards it in a way which causes the FCS to be calculated.

3.3.  Tinygram Compression

   An issue in remote Ethernet bridging is that the protocols that are
   most attractive to bridge are prone to problems on low speed (64 KBPS
   and below) lines.  This can be partially alleviated by observing that
   the vendors defining these protocols often fill the PDU with octets
   of ZERO.  Thus, an Ethernet or IEEE 802.3 PDU received from a line
   that is (1) smaller than the minimum PDU size, and (2) has a LAN
   Frame Checksum present, must be padded by inserting zeroes between
   the last four octets and the rest of the PDU before transmitting it
   on a LAN.  These protocols are frequently used for interactive
   sessions, and therefore are frequently this small.

   To prevent ambiguity, PDUs requiring padding are explicitly tagged.
   Compression is at the option of the transmitting station, and is
   probably performed only on low speed lines, perhaps under
   configuration control.

   The pseudo-code in Appendix B describes the algorithms.

3.4.  Virtual LANs

   IEEE 802.1Q defines Virtual LANs and their exchangeable VLAN Tagged
   frame format. Virtual LANs allow user multiple community groups to
   co-exist within one bridge. A bridging community is identified by its
   VLAN ID. If a system that supports Virtual LANs receives a frame from
   the LAN, that frame will be only emitted onto a LAN which belongs to
   the same community. In order to handle multiple communities on a
   single line, IEEE 802.1Q defines a VLAN Tagged Frame.






Higashiyama & Baker         Standards Track                     [Page 8]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   For example, suppose you have the following configuration:

           E1     +--+            +--+     E3
      ------------|  |            |  |------------
                  |  |     W1     |  |
                  |B1|------------|B2|
           E2     |  |            |  |     E4
      ------------|  |            |  |------------
                  +--+            +--+

   E1, E2, E3, and E4 are Ethernet LANs (or Token Ring, FDDI, etc.).  W1
   is a WAN (PPP over T1).  B1 and B2 are MAC level bridges.

   You want End Stations on E1 and E3 to communicate, and you want End
   Stations on E2 and E4 to communicate, but you do not want End
   Stations on E1 and E3 to communicate with End Stations on E2 and E4.

   This is true for Unicast, Multicast, and Broadcast traffic.  If a
   broadcast datagram originates on E1, you want it only to be
   propagated to E3, and not on E2 or E4.

   Another way of looking at it is that E1 and E3 form a Virtual LAN,
   and E2 and E4 form a Virtual LAN, as if the following configuration
   were actually being used:

           E1     +--+     W2     +--+     E3
      ------------|B3|------------|B4|------------
                  +--+            +--+

           E2     +--+     W3     +--+     E4
      ------------|B5|------------|B6|------------
                  +--+            +--+

4.  A PPP Network Control Protocol for Bridging

   The Bridging Control Protocol (BCP) is responsible for configuring,
   enabling and disabling the bridge protocol modules on both ends of
   the point-to-point link.  BCP uses the same packet exchange mechanism
   as the Link Control Protocol.  BCP packets may not be exchanged until
   PPP has reached the Network-Layer Protocol phase.  BCP packets
   received before this phase is reached SHOULD be silently discarded.

   The Bridging Control Protocol is exactly the same as the Link Control
   Protocol [6] with the following exceptions:







Higashiyama & Baker         Standards Track                     [Page 9]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   Frame Modifications

      The packet may utilize any modifications to the basic frame format
      which have been negotiated during the Link Establishment phase.

      Implementations SHOULD NOT negotiate Address-and-Control-Field-
      Compression or Protocol-Field-Compression on other than low speed
      links.

   Data Link Layer Protocol Field

      Exactly one BCP packet is encapsulated in the PPP Information
      field, where the PPP Protocol field indicates type hex 8031 (BCP).

   Code field

      Only Codes 1 through 7 (Configure-Request, Configure-Ack,
      Configure-Nak, Configure-Reject, Terminate-Request, Terminate-Ack
      and Code-Reject) are used.  Other Codes SHOULD be treated as
      unrecognized and SHOULD result in Code-Rejects.

   Timeouts

      BCP packets may not be exchanged until PPP has reached the
      Network-Layer Protocol phase.  An implementation SHOULD be
      prepared to wait for Authentication and Link Quality Determination
      to finish before timing out waiting for a Configure-Ack or other
      response.  It is suggested that an implementation give up only
      after user intervention or a configurable amount of time.

   Configuration Option Types

      BCP has a distinct set of Configuration Options, which are defined
      in this document.

4.1.  Sending Bridge Frames

   Before any Bridged LAN Traffic or BPDUs may be communicated, PPP MUST
   reach the Network-Layer Protocol phase, and the Bridging Control
   Protocol MUST reach the Opened state.

   Exactly one Bridged LAN Traffic or BPDU is encapsulated in the PPP
   Information field, where the PPP Protocol field indicates type hex
   0031 (Bridged PDU).







Higashiyama & Baker         Standards Track                    [Page 10]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


4.1.1.  Maximum Receive Unit Considerations

   The maximum length of a Bridged datagram transmitted over a PPP link
   is the same as the maximum length of the Information field of a PPP
   encapsulated packet.  Since there is no standard method for
   fragmenting and reassembling Bridged PDUs, PPP links supporting
   Bridging MUST negotiate an MRU large enough to support the MAC Types
   that are later negotiated for Bridging support.  Because they include
   the MAC headers, even bridged Ethernet frames are larger than the
   default PPP MRU of 1500 octets.

4.1.2.  Loopback and Link Quality Monitoring

   It is strongly recommended that PPP Bridge Protocol implementations
   utilize Magic Number Loopback Detection and Link-Quality-Monitoring.
   The 802.1 Spanning Tree protocol, which is integral to both
   Transparent Bridging and Source Routing (as standardized), is
   unidirectional during normal operation.  Configuration BPDUs emanate
   from the Root system in the general direction of the leaves, without
   any reverse traffic except in response to network events.

4.1.3.  Message Sequence

   The multiple link case requires consideration of message
   sequentiality.  The transmitting system may determine either that the
   protocol being bridged requires transmissions to arrive in the order
   of their original transmission, and enqueue all transmissions on a
   given conversation onto the same link to force order preservation, or
   that the protocol does NOT require transmissions to arrive in the
   order of their original transmission, and use that knowledge to
   optimize the utilization of several links, enqueuing traffic to
   multiple links to minimize delay.

   In the absence of such a determination, the transmitting system MUST
   act as though all protocols require order preservation.  Many
   protocols designed primarily for use on a single LAN require order
   preservation.

   PPP Multilink [7] and its multi-class extension [11] may be used to
   allow the use of multiple PPP links between a pair of systems without
   loss of message sequentiality. It treats the group of links as a
   single link with speed equal to the sum of the speeds of the links in
   the group.








Higashiyama & Baker         Standards Track                    [Page 11]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


4.1.4.  Separation of Spanning Tree Domains

   It is conceivable that a network manager might wish to inhibit the
   exchange of BPDUs on a link in order to logically divide two regions
   into separate Spanning Trees with different Roots (and potentially
   different Spanning Tree implementations or algorithms).  In order to
   do that, he should configure both ends to not exchange BPDUs on a
   link.  An implementation that does not support any spanning tree
   protocol MUST silently discard any received IEEE 802.1D BPDU packets.

   If a bridge is connected to an old BCP bridge [10], the other bridge
   cannot operate according to this specification. Options are therefore
   to decide that:

   (a) If the bridge wants to terminate the connection, it sends a
       Terminate-Request and terminate the connection.
   (b) If the bridge wants to run the connection but not receive old
       BPDUs, its only option is to run without spanning tree on the
       link at all, which is dangerous. It should Configure-Reject the
       option and advise the network administration that it has done so.
   (c) If the bridge chooses to be entirely backward compatible, it
       sends Configure-Ack and operates in the manner described in
       Appendix A.

   In the event that both the new Management-Inline Option and the
   Spanning-Tree-Protocol-Configuration Option are configure-rejected,
   indicating that the peer implements no spanning tree protocol at all
   and doesn't understand the options, it is an incomplete
   implementation. For safety reasons the system should cease attempting
   to configure bridging, and log the fact. If the peer was configure-
   rejecting the options in order to disable spanning tree entirely, it
   understood the option but could not within its configuration comply.
   It should have sent the Spanning-Tree-Protocol-Configuration Option
   with the value NULL.

   Implementations SHOULD implement a backward compatibility mode.

4.2.  Bridged LAN Traffic (IEEE 802 Untagged Frame)

   For Bridging LAN traffic, the format of the frame on the line is
   shown below. This format is used if the traffic does not include VLAN
   ID and priority.

   The fields are transmitted from left to right.







Higashiyama & Baker         Standards Track                    [Page 12]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   802.3 Frame format (IEEE 802 Un-tagged Frame)

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+
     |   HDLC FLAG   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |      Address and Control      |      0x00     |      0x31     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |F|0|Z|0| Pads  |    MAC Type   |      Destination MAC Address  |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                       Destination MAC Address                 |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                       Source MAC Address                      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     Source MAC Address        |      Length/Type              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |               LLC data       ...
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                   LAN FCS (optional)                          |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                potential line protocol pad                    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |          Frame FCS            |   HDLC FLAG   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


























Higashiyama & Baker         Standards Track                    [Page 13]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   802.4/802.5/FDDI Frame format (IEEE 802 Un-tagged Frame)

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+
     |   HDLC FLAG   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |      Address and Control      |      0x00     |      0x31     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |F|0|Z|0| Pads  |    MAC Type   |   Pad Byte    | Frame Control |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                       Destination MAC Address                 |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     Destination MAC Address   |  Source MAC Address           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                       Source MAC Address                      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |               LLC data       ...
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                   LAN FCS (optional)                          |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |              optional Data Link Layer padding                 |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |          Frame FCS            |   HDLC FLAG   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Address and Control

      As defined by the framing in use.

   PPP Protocol

      0x0031 for PPP Bridging

   Flags

      bit F:  Set if the LAN FCS Field is present
      bit Z:  Set if IEEE 802.3 Pad must be zero filled to minimum size
      bit 0:  reserved, must be zero

   Pads

      Any PPP frame may have padding inserted in the "Optional Data Link
      Layer Padding" field.  This number tells the receiving system how
      many pad octets to strip off.






Higashiyama & Baker         Standards Track                    [Page 14]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   MAC Type

      Up-to-date values of the MAC Type field are specified in the most
      recent "Assigned Numbers" RFC [4].  Current values are assigned as
      follows:

          0: reserved
          1: IEEE 802.3/Ethernet  with canonical addresses
          2: IEEE 802.4           with canonical addresses
          3: IEEE 802.5           with non-canonical addresses
          4: FDDI                 with non-canonical addresses
       5-10: reserved
         11: IEEE 802.5           with canonical addresses
         12: FDDI                 with canonical addresses

      "Canonical" is the address format defined as standard address
      representation by the IEEE.  In this format, the bit within each
      byte that is to be transmitted first on a LAN is represented as
      the least significant bit.  In contrast, in non-canonical form,
      the bit within each byte that is to be transmitted first is
      represented as the most-significant bit.  Many LAN interface
      implementations use non-canonical form.  In both formats, bytes
      are represented in the order of transmission.

      If an implementation supports a MAC Type that is the higher-
      numbered format of that MAC Type, then it MUST also support the
      lower-numbered format of that MAC Type.  For example, if an
      implementation supports FDDI with canonical address format, then
      it MUST also support FDDI with non-canonical address format.  The
      purpose of this requirement is to provide backward compatibility
      with earlier versions of this specification.

      A system MUST NOT transmit a MAC Type numbered higher than 4
      unless it has received from its peer a MAC-Support Configuration
      Option indicating that the peer is willing to receive frames of
      that MAC Type.

   Frame Control

      On 802.4, 802.5, and FDDI LANs, there are a few octets preceding
      the Destination MAC Address, one of which is protected by the FCS.

      The MAC Type of the frame determines the contents of the Frame
      Control field.  A pad octet is present to provide 32-bit packet
      alignment.






Higashiyama & Baker         Standards Track                    [Page 15]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   Destination MAC Address

      As defined by the IEEE.  The MAC Type field defines the bit
      ordering.

   Source MAC Address

      As defined by the IEEE.  The MAC Type field defines the bit
      ordering.

   LLC data

      This is the remainder of the MAC frame which is (or would be were
      it present) protected by the LAN FCS.

      For example, the 802.5 Access Control field, and Status Trailer
      are not meaningful to transmit to another ring, and are omitted.

   LAN FCS

      If present, this is the LAN FCS which was calculated by (or which
      appears to have been calculated by) the originating station.  If
      the LAN FCS flag is not set, then this field is not present, and
      the PDU is four octets shorter.

   Optional Data Link Layer Padding

      Any PPP frame may have padding inserted between the Information
      field and the Frame FCS.  The Pads field contains the length of
      this padding, which may not exceed 15 octets.

      The PPP LCP Extensions [5] specify a self-describing pad.
      Implementations are encouraged to set the Pads field to zero, and
      use the self-describing pad instead.

   Frame FCS

      Mentioned primarily for clarity.  The FCS used on the PPP link is
      separate from and unrelated to the LAN FCS.

4.3.  Bridged LAN Traffic in IEEE 802 Tagged Frame

   To connect two or more Virtual LAN segments, the frame MUST include
   its VLAN ID and priority. An IEEE 802 Tagged Frame may be used if the
   IEEE-802-Tagged-Frame Option is accepted by the peer. The format of
   the frame on the line is shown below.

   The fields are transmitted from left to right.



Higashiyama & Baker         Standards Track                    [Page 16]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   802.3 Frame format (IEEE 802 Tagged Frame)

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+
      |   HDLC FLAG   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |      Address and Control      |      0x00     |      0x31     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |F|0|Z|0| Pads  |    MAC Type   |      Destination MAC Address  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                       Destination MAC Address                 |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                       Source MAC Address                      |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |     Source MAC Address        |     0x81       |     0x00     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |Pri  |C| VLAN ID               |      Length/Type              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |               LLC data       ...
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   LAN FCS (optional)                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                potential line protocol pad                    |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |          Frame FCS            |   HDLC FLAG   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
























Higashiyama & Baker         Standards Track                    [Page 17]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   802.4/802.5/FDDI Frame format (IEEE 802 Tagged Frame)

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+
     |   HDLC FLAG   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |      Address and Control      |      0x00     |      0x31     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |F|0|Z|0| Pads  |    MAC Type   |   Pad Byte    | Frame Control |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                       Destination MAC Address                 |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     Destination MAC Address   |  Source MAC Address           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                       Source MAC Address                      |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                   SNAP-encoded TPID                           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                   SNAP-encoded TPID                           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |Pri  |C| VLAN ID               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |               LLC data       ...
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                   LAN FCS (optional)                          |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |              optional Data Link Layer padding                 |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |          Frame FCS            |   HDLC FLAG   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Address and Control

      As defined by the framing in use.

   PPP Protocol

      0x0031 for PPP Bridging

   Flags

      bit F:  Set if the LAN FCS Field is present
      bit Z:  Set if IEEE 802.3 Pad must be zero filled to minimum size
      bit 0:  reserved, must be zero






Higashiyama & Baker         Standards Track                    [Page 18]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   Pads

      Any PPP frame may have padding inserted in the "Optional Data Link
      Layer Padding" field.  This number tells the receiving system how
      many pad octets to strip off.

   MAC Type

      Up-to-date values of the MAC Type field are specified in the most
      recent "Assigned Numbers" RFC [4].  Current values are assigned as
      follows:

          0: reserved
          1: IEEE 802.3/Ethernet  with canonical addresses
          2: IEEE 802.4           with canonical addresses
          3: IEEE 802.5           with non-canonical addresses
          4: FDDI                 with non-canonical addresses
       5-10: reserved
         11: IEEE 802.5           with canonical addresses
         12: FDDI                 with canonical addresses

      "Canonical" is the address format defined as standard address
      representation by the IEEE.  In this format, the bit within each
      byte that is to be transmitted first on a LAN is represented as
      the least significant bit.  In contrast, in non-canonical form,
      the bit within each byte that is to be transmitted first is
      represented as the most-significant bit.  Many LAN interface
      implementations use non-canonical form.  In both formats, bytes
      are represented in the order of transmission.

      If an implementation supports a MAC Type that is the higher-
      numbered format of that MAC Type, then it MUST also support the
      lower-numbered format of that MAC Type.  For example, if an
      implementation supports FDDI with canonical address format, then
      it MUST also support FDDI with non-canonical address format.  The
      purpose of this requirement is to provide backward compatibility
      with earlier versions of this specification.

      A system MUST NOT transmit a MAC Type numbered higher than 4
      unless it has received from its peer a MAC-Support Configuration
      Option indicating that the peer is willing to receive frames of
      that MAC Type.

   Frame Control

      On 802.4, 802.5, and FDDI LANs, there are a few octets preceding
      the Destination MAC Address, one of which is protected by the FCS.




Higashiyama & Baker         Standards Track                    [Page 19]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


      The MAC Type of the frame determines the contents of the Frame
      Control field.  A pad octet is present to provide 32-bit packet
      alignment.

   Destination MAC Address

      As defined by the IEEE.  The MAC Type field defines the bit
      ordering.

   Source MAC Address

      As defined by the IEEE.  The MAC Type field defines the bit
      ordering.

   Pri
      3 bit priority value as defined by IEEE 802.1D.

   C
      Canonical flag as defined by IEEE 802.1Q. It must be set if RIF
      data is present in the LLC data.

   VLAN ID
      12 bit VLAN identifier number as defined by IEEE 802.1Q.

   LLC data

      This is the remainder of the MAC frame which is (or would be were
      it present) protected by the LAN FCS.

      For example, the 802.5 Access Control field, and Status Trailer
      are not meaningful to transmit to another ring, and are omitted.

   LAN FCS

      If present, this is the LAN FCS which was calculated by (or which
      appears to have been calculated by) the originating station.  If
      the LAN FCS flag is not set, then this field is not present, and
      the PDU is four octets shorter.

   Optional Data Link Layer Padding

      Any PPP frame may have padding inserted between the Information
      field and the Frame FCS.  The Pads field contains the length of
      this padding, which may not exceed 15 octets.

      The PPP LCP Extensions [5] specify a self-describing pad.
      Implementations are encouraged to set the Pads field to zero, and
      use the self-describing pad instead.



Higashiyama & Baker         Standards Track                    [Page 20]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   Frame FCS

      Mentioned primarily for clarity.  The FCS used on the PPP link is
      separate from and unrelated to the LAN FCS.

4.4. Bridge protocols and GARP protocols

   To avoid network loops and improve redundancy, Bridges exchange a
   Spanning Tree Protocol data unit known as BPDU. Bridges also exchange
   a Generic Attributes Registration Protocol data unit to carry the
   GARP VLAN Registration Protocol (GVRP) data and GARP Multicast
   Registration Protocol (GMRP). GVRP allow the Bridges to create VLAN
   groups dynamically. GMRP allows bridges to filter Multicast data if
   the receiver is absent from the network. These Bridge protocols
   include Spanning Tree Protocol and GARP protocols data units are
   carried with a special destination address assigned by the IEEE.

   These bridge protocols data units and GARP protocol data units must
   be carried in the frame format shown in section 4.2 or 4.3. The
   Bridge that receives these data units identifies these protocols
   based on the destination address in the frame format, just like the
   operation of receiving frames from a LAN segment.

   Bridge protocols and GARP protocols data units MUST be recognized by
   checking the destination addresses, which are assigned by IEEE.

      01-80-c2-00-00-00  Bridge Group Address (used by STP)
      01-80-c2-00-00-01  IEEE Std. 802.3x Full Duplex PAUSE operation
      01-80-c2-00-00-10  Bridge Management Group Address
      01-80-c2-00-00-20  GARP Multicast Registration Protocol (GMRP)
      01-80-c2-00-00-21  GARP VLAN Registration Protocol (GVRP)

   But there is one exception to this rule: if the bridge is connected
   to an old BCP bridge [10] and can support backward compatibility, it
   MUST send the BPDU in the old format described in Appendix A.

5.  BCP Configuration Options

   BCP Configuration Options allow modifications to the standard
   characteristics of the network-layer protocol to be negotiated.  If a
   Configuration Option is not included in a Configure-Request packet,
   the default value for that Configuration Option is assumed.

   BCP uses the same Configuration Option format defined for LCP [6],
   with a separate set of Options.






Higashiyama & Baker         Standards Track                    [Page 21]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   Up-to-date values of the BCP Option Type field are specified in the
   most recent "Assigned Numbers" RFC [4].  Current values are assigned
   as follows:

         1       Bridge-Identification
         2       Line-Identification
         3       MAC-Support
         4       Tinygram-Compression
         5       LAN-Identification (obsoleted)
         6       MAC-Address
         7       Spanning-Tree-Protocol (old formatted)
         8       IEEE 802 Tagged Frame
         9       Management Inline

5.1.  Bridge-Identification

   Description

      The Bridge-Identification Configuration Option is designed for use
      when the line is an interface between half bridges connecting
      virtual or physical LAN segments.  Since these remote bridges are
      modeled as a single bridge with a strange internal interface, each
      remote bridge needs to know the LAN segment and bridge numbers of
      the adjacent remote bridge.  This option MUST NOT be included in
      the same Configure-Request as the Line-Identification option.

      The Source Routing Route Descriptor and its use are specified by
      the IEEE 802.1D Appendix on Source Routing.  It identifies the
      segment to which the interface is attached by its configured
      segment number, and itself by bridge number on the segment.

      The two half bridges MUST agree on the bridge number.  If a bridge
      number is not agreed upon, the Bridging Control Protocol MUST NOT
      enter the Opened state.

      Since mismatched bridge numbers are indicative of a configuration
      error, a correct configuration requires that either the bridge
      declare the misconfiguration or choose one of the options.  To
      allow two systems to proceed to the Opened state despite a
      mismatch, a system MAY change its bridge number to the higher of
      the two numbers. A higher-numbered system MUST NOT change its
      bridge number to a lower number. It should, however, inform the
      network administration of the misconfiguration in any case.

      By default, a system that does not negotiate this option is
      assumed to be configured not to use the model of the two systems
      as two halves of a single source-route bridge.  It is instead




Higashiyama & Baker         Standards Track                    [Page 22]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


      assumed to be configured to use the model of the two systems as
      two independent bridges.

   Example

      If System A announces LAN Segment AAA, Bridge #1, and System B
      announces LAN Segment BBB, Bridge #1, then the resulting Source
      Routing configuration (read in the appropriate direction) is then
      AAA,1,BBB.

   A summary of the Bridge-Identification Option format is shown below.
   The fields are transmitted from left to right.

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |     Type      |    Length     | LAN Segment Number    |Bridge#|
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Type

      1

   Length

      4

   LAN Segment Number

      A 12-bit number identifying the LAN segment, as defined in the
      IEEE 802.1D Source Routing Specification.

   Bridge Number

      A 4-bit number identifying the bridge on the LAN segment, as
      defined in the IEEE 802.1D Source Routing Specification.

5.2.  Line-Identification

   Description

      The Line-Identification Configuration Option is designed for use
      when the line is assigned a LAN segment number as though it were a
      two system LAN segment in accordance with the Source Routing
      algorithm.






Higashiyama & Baker         Standards Track                    [Page 23]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


      The Source Routing Route Descriptor and its use are specified by
      the IEEE 802.1D Appendix on Source Routing.  It identifies the
      segment to which the interface is attached by its configured
      segment number, and itself by bridge number on the segment.

      The two bridges MUST agree on the LAN segment number.  If a LAN
      segment number is not agreed upon, the Bridging Control Protocol
      MUST NOT enter the Opened state.

      Since mismatched LAN segment numbers are indicative of a
      configuration error, a correct configuration requires that either
      the bridge declare the misconfiguration or choose one of the
      options.  To allow two systems to proceed to the Opened state
      despite a mismatch, a system MAY change its LAN segment number to
      the higher of the two numbers.  A higher-numbered system MUST NOT
      change its LAN segment number to a lower number. It should,
      however, inform the network administration of the misconfiguration
      in any case.

      By default, a system that does not negotiate this option is
      assumed to have its LAN segment number correctly configured by the
      user.

   A summary of the Line-Identification Option format is shown below.
   The fields are transmitted from left to right.

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |     Type      |    Length     | LAN Segment Number    |Bridge#|
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Type

      2

   Length

      4

   LAN Segment Number

      A 12-bit number identifying the LAN segment, as defined in the
      IEEE 802.1D Source Routing Specification.







Higashiyama & Baker         Standards Track                    [Page 24]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   Bridge Number

      A 4-bit number identifying the bridge on the LAN segment, as
      defined in the IEEE 802.1D Source Routing Specification.

5.3.  MAC-Support

   Description

      The MAC-Support Configuration Option is provided to permit
      implementations to indicate the sort of traffic they are prepared
      to receive.  Negotiation of this option is strongly recommended.

      By default, when an implementation does not announce the MAC Types
      that it supports, all MAC Types are sent by the peer which are
      capable of being transported given other configuration parameters.
      The receiver will discard those MAC Types that it does not
      support.

      A device supporting a 1600 octet MRU might not be willing to
      support 802.5, 802.4 or FDDI, which each support frames larger
      than 1600 octets.

      By announcing the MAC Types it will support, an implementation is
      advising its peer that all unspecified MAC Types will be
      discarded.  The peer MAY then reduce bandwidth usage by not
      sending the unsupported MAC Types.

      Announcement of support for multiple MAC Types is accomplished by
      placing multiple options in the Configure-Request.

      The nature of this option is advisory only.  This option MUST NOT
      be included in a Configure-Nak.

   A summary of the MAC-Support Option format is shown below.  The
   fields are transmitted from left to right.

     0                   1                   2
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |     Type      |    Length     |    MAC Type   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Type

      3





Higashiyama & Baker         Standards Track                    [Page 25]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   Length

      3

   MAC Type

      One of the values of the PDU MAC Type field (previously described
      in the "Bridged LAN Traffic" section) that this system is prepared
      to receive and service.

5.4.  Tinygram-Compression

   Description

      This Configuration Option permits the implementation to indicate
      support for Tinygram compression.

      Not all systems are prepared to make modifications to messages in
      transit.  On high speed lines, it is probably not worth the
      effort.

      This option MUST NOT be included in a Configure-Nak if it has been
      received in a Configure-Request.  This option MAY be included in a
      Configure-Nak in order to prompt the peer to send the option in
      its next Configure-Request.

      By default, no compression is allowed.  A system which does not
      negotiate, or negotiates this option to be disabled, should never
      receive a compressed packet.

   A summary of the Tinygram-Compression Option format is shown below.
   The fields are transmitted from left to right.

     0                   1                   2
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |     Type      |    Length     | Enable/Disable|
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Type

      4

   Length

      3





Higashiyama & Baker         Standards Track                    [Page 26]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   Enable/Disable

      If the value is 1, Tinygram-Compression is enabled.  If the value
      is 2, Tinygram-Compression is disabled, and no decompression will
      occur.

      The implementations need not agree on the setting of this
      parameter.  One may be willing to decompress and the other not.

5.5.  MAC-Address

   Description

      The MAC-Address Configuration Option enables the implementation to
      announce its MAC address or have one assigned.  The MAC address is
      represented in IEEE 802.1 Canonical format, which is to say that
      the multicast bit is the least significant bit of the first octet
      of the address.

      If the system wishes to announce its MAC address, it sends the
      option with its MAC address specified.  When specifying a non-zero
      MAC address in a Configure-Request, any inclusion of this option
      in a Configure-Nak MUST be ignored.

      If the implementation wishes to have a MAC address assigned, it
      sends the option with a MAC address of 00-00-00-00-00-00.  Systems
      that have no mechanism for address assignment will Configure-
      Reject the option.

      A Configure-Nak MUST specify a valid IEEE 802.1 format physical
      address; the multicast bit MUST be zero.  It is strongly
      recommended (although not mandatory) that the "locally assigned
      address" bit (the second least significant bit in the first octet)
      be set, indicating a locally assigned address.

   A summary of the MAC-Address Option format is shown below.  The
   fields are transmitted from left to right.

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |     Type      |    Length     |MAC byte 1 |L|M|  MAC byte 2   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  MAC byte 3   |  MAC byte 4   |  MAC byte 5   |  MAC byte 6   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+






Higashiyama & Baker         Standards Track                    [Page 27]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   Type

      6

   Length

      8

   MAC Byte

      Six octets of MAC address in 802.1 Canonical order.  For clarity,
      the position of the Local Assignment (L) and Multicast (M) bits
      are shown in the diagram.

5.6.  Spanning-Tree-Protocol (old format)

   Description

      The Spanning-Tree-Protocol Configuration enables a Bridge to
      remain compatible with older implementations of BCP [10]. This
      configuration option is, however, incompatible with the
      Management-Inline option, which enables a bridge to implement the
      many protocols that IEEE now expects a bridge to be able to use.

      If the peer rejects the Management-Inline configuration option, by
      sending configure-reject, it must be an implementation of [10],
      which is described in Appendix A. The system may optionally
      terminate the negotiation or offer to negotiate in that manner.

      In this case, if both bridges support a spanning tree protocol,
      they MUST agree on the protocol to be supported. The old BPDU
      described in Appendix A MUST be used rather than the format shown
      in section 4.2 or 4.3. When the two disagree, the lower-numbered
      of the two spanning tree protocols should be used.  To resolve the
      conflict, the system with the lower-numbered protocol SHOULD
      Configure-Nak the option, suggesting its own protocol for use. If
      a spanning tree protocol is not agreed upon, except for the case
      in which one system does not support any spanning tree protocol,
      the Bridging Control Protocol MUST NOT enter the Opened state.

      Most systems will only participate in a single spanning tree
      protocol.  If a system wishes to participate simultaneously in
      more than one spanning tree protocol, it MAY include all of the
      appropriate protocol types in a single Spanning-Tree-Protocol
      Configuration Option.  The protocol types MUST be specified in
      increasing numerical order.  For the purpose of comparison during
      negotiation, the protocol numbers MUST be considered to be a
      single number.  For instance, if System A includes protocols 01



Higashiyama & Baker         Standards Track                    [Page 28]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


      and 03 and System B indicates protocol 03, System B should
      Configure-Nak and indicate a protocol type of 03 since 0103 is
      greater than 03.

      By default, an implementation MUST either support the IEEE 802.1D
      spanning tree or support no spanning tree protocol.  An
      implementation that does not support any spanning tree protocol
      MUST silently discard any received IEEE 802.1D BPDU packets, and
      MUST either silently discard or respond to other received BPDU
      packets with an LCP Protocol-Reject packet in this case.

   A summary of the Spanning-Tree-Protocol Option format is shown below.
   The fields are transmitted from left to right.

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
    |     Type      |    Length     |  Protocol 1   |  Protocol 2   | ..
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

   Type

      7

   Length

      2 octets plus 1 additional octet for each protocol that will be
      actively supported.  Most systems will only support a single
      spanning tree protocol, resulting in a length of 3.

   Protocol n

      Each Protocol field is one octet and indicates a desired spanning
      tree protocol. Up-to-date values of the Spanning-Tree-Protocol
      field are specified as PPP DLL numbers in the most recent
      "Assigned Numbers" RFC [4].  Current values are assigned as
      follows:

            Value     Protocol

              0       Null (no Spanning Tree protocol supported)
              1       IEEE 802.1D spanning tree
              2       IEEE 802.1G extended spanning tree protocol
              3       IBM Source Route Spanning tree protocol
              4       DEC LANbridge 100 Spanning tree protocol






Higashiyama & Baker         Standards Track                    [Page 29]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


5.7.  IEEE-802-Tagged-Frame

   Description

      This configuration option permits the implementation to indicate
      support for IEEE 802 Tagged Frame. Negotiation of this option is
      strongly recommended.

      A device supporting IEEE 802 Tagged Frame must be willing to
      support IEEE 802 Tagged Frame shown in section 4.3.

      By default, IEEE 802 Tagged Frame is not supported. A system which
      does not negotiate, or negotiates this option to be disabled,
      should never receive a IEEE 802 Tagged Frame.

   A summary of the IEEE 802 Tagged Frame Option format is shown below.
   The fields are transmitted from left to right.

     0                   1                   2
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |     Type      |    Length     | Enable/Disable|
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Type

      8

   Length

      3

   Enable/Disable

      If the value is 1, IEEE-802-Tagged-Frame is enabled.  If the value
      is 2, IEEE-802-Tagged-Frame is disabled, and MUST not send any
      IEEE-802-Tagged-Frame packet.

5.8.  Management-Inline

   Description

      The Management-Inline Configuration Option indicates that the
      system is willing to receive any IEEE-defined inter-bridge
      protocols, such as bridge protocol data units and GARP protocol
      data units, in the frame format shown in section 4.2 or 4.3.





Higashiyama & Baker         Standards Track                    [Page 30]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


      Old BCP [10] implementations will use the negotiation procedure
      described in section 5.6. Implementations of this procedure will
      use this option to indicate compliance with the new BCP and may
      optionally negotiate the section 5.6 procedure, either on the same
      configure-request or in response to a configure-reject, as well.
      It is recommended that the configure-request only show this option
      when it is relevant, and that it reply with the Spanning-Tree-
      Protocol (old formatted) option if a configure-reject is received,
      as in the normal case one can expect it to be the quickest
      negotiation.

      If a system receives a configure-request offering both
      alternatives, it should accept this procedure and reject the
      Spanning-Tree-Protocol (old format) option.

      One can expect old BCP [10] implementations to not understand the
      option and issue a configure-reject.

      By default, Management-Inline is not allowed.  A system which does
      not negotiate, or negotiates this option to be disabled, should
      never receive a Bridge Protocol data unit or GARP protocol data
      unit inline.

      A summary of the Management-Inline Option format is shown below.
      The fields are transmitted from left to right.

        0                   1
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |     Type      |    Length     |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Type

      9

   Length

      2

6. Changes From RFC 1638

   This section enumerates changes made to old BCP [10] to produce this
   document.

   (1) Remove all LAN Identification descriptions and replace with IEEE
       802.1Q VLAN descriptions.




Higashiyama & Baker         Standards Track                    [Page 31]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   (2) Remove LAN Identification field from frame format and I flags
       from flag field.
   (3) Merge the Spanning Tree BPDU frame format with Bridged traffic.

7. Security Considerations

   This network control protocol compares the configurations of two
   devices and seeks to negotiate an acceptable subset of their
   intersection, to enable correct interoperation even in the presence
   of minor configuration or implementation differences. In the event
   that a major misconfiguration is detected, the negotiation will not
   complete successfully, resulting in the link coming down or not
   coming up. It is possible that if a bridged link comes up with a
   rogue peer, network information may be learned from forwarded
   multicast traffic, or denial of service attacks may be created by
   closing loops that should be detected and isolated or by offering
   rogue load.

   Such attacks are not isolated to this NCP; any PPP NCP is subject to
   attack when connecting to a foreign or compromised device. However,
   no situations arise which are not common to all NCPs; any NCP that
   comes up with a rogue peer is subject to snooping and other attacks.
   Therefore, it is recommended that links on which this may happen
   should be configured to use PPP authentication during the LCP start-
   up phase.

8. Intellectual Property Notice

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11.  Copies of
   claims of rights made available for publication and any assurances of
   licenses to be made available, or the result of an attempt made to
   obtain a general license or permission for the use of such
   proprietary rights by implementers or users of this specification can
   be obtained from the IETF Secretariat."

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.




Higashiyama & Baker         Standards Track                    [Page 32]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   The IETF has been notified of intellectual property rights claimed in
   regard to some or all of the specification contained in this
   document.  For more information consult the online list of claimed
   rights.

9. IANA Considerations

   This document proposes a total of two new BCP option numbers to be
   maintained by the IANA. These options (described in Section 5.1 and
   5.2) are IEEE-802-Tagged-Frame and Management-Inline. The IANA has
   assigned the values 8 and 9 respectively for these option numbers.

10. Acknowledgments

   This document is a product of the Point-to-Point Protocol Extensions
   Working Group.

   This document is based on the PPP Bridging Control Protocol, RFC 1638
   [10], edited by Rich Bowen of IBM and produced by the Point-to-Point
   Protocol Extensions Working Group. It extends that document by
   providing support for Virtual LANs as outlined in [9].






























Higashiyama & Baker         Standards Track                    [Page 33]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


A.  Spanning Tree Bridge PDU (old format)

   By default, Spanning Tree BPDUs MUST be encoded with a MAC or 802.2
   LLC header as described in section 4.2 or 4.3 of this document.
   However, should the remote entity Configure-Reject the Management-
   Inline option, thereby indicating that it is a purely RFC 1638
   compliant device, the local entity may subsequently encode BPDUs as
   described in section 4.3 of RFC 1638 provided that use of a suitable
   non-NULL STP protocol across the link is successfully negotiated
   using the (old) Spanning-Tree-Protocol option.

   This is the Spanning Tree BPDU used in RFC 1638, without any MAC or
   802.2 LLC header (these being functionally equivalent to the Address,
   Control, and PPP Protocol Fields).  The LAN Pad and Frame Checksum
   fields are likewise superfluous and absent.

   The Address and Control Fields are subject to LCP Address-and-
   Control-Field-Compression negotiation.

   A PPP system which is configured to participate in a particular
   spanning tree protocol and receives a BPDU of a different spanning
   tree protocol SHOULD reject it with the LCP Protocol-Reject.  A
   system which is configured not to participate in any spanning tree
   protocol MUST silently discard all BPDUs.

   Spanning Tree Bridge PDU

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+
    |   HDLC FLAG   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |      Address and Control      |     Spanning Tree Protocol    |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |              BPDU data       ...                              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |          Frame FCS            |   HDLC FLAG   |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Address and Control

      As defined by the framing in use.

   Spanning Tree Protocol

      Up-to-date values of the Spanning-Tree-Protocol field are
      specified in the most recent "Assigned Numbers" RFC [4].  Current
      values are assigned as follows:



Higashiyama & Baker         Standards Track                    [Page 34]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


         Value (in hex)  Protocol

         0201            IEEE 802.1 (either 802.1D or 802.1G)
         0203            IBM Source Route Bridge
         0205            DEC LANbridge 100

      The two versions of the IEEE 802.1 spanning tree protocol frames
      can be distinguished by fields within the BPDU data.

   BPDU data

      As defined by the specified Spanning Tree Protocol.

B.  Tinygram-Compression Pseudo-Code

   PPP Transmitter:

   if (ZeroPadCompressionEnabled &&
       BridgedProtocolHeaderFormat == IEEE8023 &&
       PacketLength == Minimum8023PacketLength) {
    /*
     * Remove any continuous run of zero octets preceding,
     * but not including, the LAN FCS, but not extending
     * into the MAC header.
     */
       Set (ZeroCompressionFlag);           /* Signal receiver */
       if (is_Set (LAN_FCS_Present)) {
           FCS = TrailingOctets (PDU, 4);   /* Store FCS */
           RemoveTrailingOctets (PDU, 4);   /* Remove FCS */
           while (PacketLength > 14 &&      /* Stop at MAC header or */
                  TrailingOctet (PDU) == 0) /*  last non-zero octet */
              RemoveTrailingOctets (PDU, 1);/* Remove zero octet */
           Appendbuf (PDU, 4, FCS);         /* Restore FCS */
       }
       else {
           while (PacketLength > 14 &&      /* Stop at MAC header */
                  TrailingOctet (PDU) == 0) /*  or last zero octet */
              RemoveTrailingOctets (PDU, 1);/* Remove zero octet */
       }
   }

   PPP Receiver:

   if (ZeroCompressionFlag) {                /* Flag set in header? */
    /* Restoring packet to minimum 802.3 length */
       Clear (ZeroCompressionFlag);
       if (is_Set (LAN_FCS_Present)) {
           FCS = TrailingOctets (PDU, 4);   /* Store FCS */



Higashiyama & Baker         Standards Track                    [Page 35]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


           RemoveTrailingOctets (PDU, 4);   /* Remove FCS */
           Appendbuf (PDU, 60 - PacketLength, zeroes);/* Add zeroes */
           Appendbuf (PDU, 4, FCS);         /* Restore FCS */
       }
       else {
           Appendbuf (PDU, 60 - PacketLength, zeroes);/* Add zeroes */
       }
   }

References

   [1]  IBM, "Token-Ring Network Architecture Reference", 3rd edition,
        September 1989.

   [2]  IEEE 802.1, "Draft Standard 802.1G: Remote MAC Bridging",
        P802.1G/D7, December 30, 1992.

   [3]  IEEE 802.1D-1993, "Media Access Control (MAC) Bridges", ISO/IEC
        15802-3:1993 ANSI/IEEE Std 802.1D, 1993 edition., July 1993.

   [4]  Reynolds, J. and J. Postel, "Assigned Numbers", STD 2, RFC 1700,
        October 1994.  See also: http://www.iana.org/numbers.html

   [5]  Simpson, W., "PPP LCP Extensions", RFC 1570, January 1994.

   [6]  Simpson, W., "The Point-to-Point Protocol (PPP)", STD 51, RFC
        1661, July 1994.

   [7]  Sklower, K., Lloyd, B., McGregor, G., Carr, D. and T. Coradetti,
        "The PPP Multilink Protocol (MP)", RFC 1990, August 1996.

   [8]  IEEE 802.1D-1998, "Information technology - Telecommunications
        and Information exchange between systems - Local and
        metropolitan area networks - Common Specifications - Part 3:
        Media Access Control (MAC) Bridges: Revision. This is a revision
        of ISO/IEC 10038: 1993, 802.1j-1992 and 802.6k-1992. It
        incorporates P802.11c, P802.1p and P802.12e." ISO/IEC 15802-3:
        1998.

   [9]  IEEE 802.1Q, ANSI/IEEE Standard 802.1Q, "IEEE Standards for
        Local and Metropolitan Area Networks: Virtual Bridged Local Area
        Networks", 1998.

   [10] Baker, F. and R. Bowen, "PPP Bridging Control Protocol (BCP)",
        RFC 1638, June 1994.

   [11] Bormann, C., "The Multi-Class Extension to Multi-Link PPP", RFC
        2686, September 1999.



Higashiyama & Baker         Standards Track                    [Page 36]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


   [12] Bradner, S., "Key words for use in RFCs to Indicate Requirement
        Levels", BCP 14, RFC 2119, March 1997.

Authors' Addresses

   Questions about this memo can also be directed to:

   Mitsuru Higashiyama
   Anritsu Corporation
   1800 Onna, Atsugi-shi, Kanagawa-prf., 243-8555 Japan

   Phone: +81 (46) 296-6625
   EMail: Mitsuru.Higashiyama@yy.anritsu.co.jp


   Fred Baker
   519 Lado Drive
   Santa Barbara, California 93111

   EMail: fred.baker@cisco.com































Higashiyama & Baker         Standards Track                    [Page 37]

RFC 2878          PPP Bridging Control Protocol (BCP)          July 2000


Full Copyright Statement

   Copyright (C) The Internet Society (2000).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.



















Higashiyama & Baker         Standards Track                    [Page 38]