1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394
1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
1444
1445
1446
1447
1448
1449
1450
1451
1452
1453
1454
1455
1456
1457
1458
1459
1460
1461
1462
1463
1464
1465
1466
1467
1468
1469
1470
1471
1472
1473
1474
1475
1476
1477
1478
1479
1480
1481
1482
1483
1484
1485
1486
1487
1488
1489
1490
1491
1492
1493
1494
1495
1496
1497
1498
1499
1500
1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515
1516
1517
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538
1539
1540
1541
1542
1543
1544
1545
1546
1547
1548
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
|
<pre>Network Working Group T. Socolofsky
Request for Comments: 1180 C. Kale
Spider Systems Limited
January 1991
<span class="h1">A TCP/IP Tutorial</span>
Status of this Memo
This RFC is a tutorial on the TCP/IP protocol suite, focusing
particularly on the steps in forwarding an IP datagram from source
host to destination host through a router. It does not specify an
Internet standard. Distribution of this memo is unlimited.
Table of Contents
<a href="#section-1">1</a>. Introduction................................................ <a href="#page-1">1</a>
<a href="#section-2">2</a>. TCP/IP Overview............................................. <a href="#page-2">2</a>
<a href="#section-3">3</a>. Ethernet.................................................... <a href="#page-8">8</a>
<a href="#section-4">4</a>. ARP......................................................... <a href="#page-9">9</a>
<a href="#section-5">5</a>. Internet Protocol........................................... <a href="#page-12">12</a>
<a href="#section-6">6</a>. User Datagram Protocol...................................... <a href="#page-22">22</a>
<a href="#section-7">7</a>. Transmission Control Protocol............................... <a href="#page-24">24</a>
<a href="#section-8">8</a>. Network Applications........................................ <a href="#page-25">25</a>
<a href="#section-9">9</a>. Other Information........................................... <a href="#page-27">27</a>
<a href="#section-10">10</a>. References.................................................. <a href="#page-27">27</a>
<a href="#section-11">11</a>. Relation to other RFCs...................................... <a href="#page-27">27</a>
<a href="#section-12">12</a>. Security Considerations..................................... <a href="#page-27">27</a>
<a href="#section-13">13</a>. Authors' Addresses.......................................... <a href="#page-28">28</a>
<span class="h2"><a class="selflink" id="section-1" href="#section-1">1</a>. Introduction</span>
This tutorial contains only one view of the salient points of TCP/IP,
and therefore it is the "bare bones" of TCP/IP technology. It omits
the history of development and funding, the business case for its
use, and its future as compared to ISO OSI. Indeed, a great deal of
technical information is also omitted. What remains is a minimum of
information that must be understood by the professional working in a
TCP/IP environment. These professionals include the systems
administrator, the systems programmer, and the network manager.
This tutorial uses examples from the UNIX TCP/IP environment, however
the main points apply across all implementations of TCP/IP.
Note that the purpose of this memo is explanation, not definition.
If any question arises about the correct specification of a protocol,
please refer to the actual standards defining RFC.
<span class="grey">Socolofsky & Kale [Page 1]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-2" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
The next section is an overview of TCP/IP, followed by detailed
descriptions of individual components.
<span class="h2"><a class="selflink" id="section-2" href="#section-2">2</a>. TCP/IP Overview</span>
The generic term "TCP/IP" usually means anything and everything
related to the specific protocols of TCP and IP. It can include
other protocols, applications, and even the network medium. A sample
of these protocols are: UDP, ARP, and ICMP. A sample of these
applications are: TELNET, FTP, and rcp. A more accurate term is
"internet technology". A network that uses internet technology is
called an "internet".
<span class="h3"><a class="selflink" id="section-2.1" href="#section-2.1">2.1</a> Basic Structure</span>
To understand this technology you must first understand the following
logical structure:
----------------------------
| network applications |
| |
|... \ | / .. \ | / ...|
| ----- ----- |
| |TCP| |UDP| |
| ----- ----- |
| \ / |
| -------- |
| | IP | |
| ----- -*------ |
| |ARP| | |
| ----- | |
| \ | |
| ------ |
| |ENET| |
| ---@-- |
----------|-----------------
|
----------------------o---------
Ethernet Cable
Figure 1. Basic TCP/IP Network Node
This is the logical structure of the layered protocols inside a
computer on an internet. Each computer that can communicate using
internet technology has such a logical structure. It is this logical
structure that determines the behavior of the computer on the
internet. The boxes represent processing of the data as it passes
through the computer, and the lines connecting boxes show the path of
<span class="grey">Socolofsky & Kale [Page 2]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-3" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
data. The horizontal line at the bottom represents the Ethernet
cable; the "o" is the transceiver. The "*" is the IP address and the
"@" is the Ethernet address. Understanding this logical structure is
essential to understanding internet technology; it is referred to
throughout this tutorial.
<span class="h3"><a class="selflink" id="section-2.2" href="#section-2.2">2.2</a> Terminology</span>
The name of a unit of data that flows through an internet is
dependent upon where it exists in the protocol stack. In summary: if
it is on an Ethernet it is called an Ethernet frame; if it is between
the Ethernet driver and the IP module it is called a IP packet; if it
is between the IP module and the UDP module it is called a UDP
datagram; if it is between the IP module and the TCP module it is
called a TCP segment (more generally, a transport message); and if it
is in a network application it is called a application message.
These definitions are imperfect. Actual definitions vary from one
publication to the next. More specific definitions can be found in
<a href="./rfc1122#section-1.3.3">RFC 1122, section 1.3.3</a>.
A driver is software that communicates directly with the network
interface hardware. A module is software that communicates with a
driver, with network applications, or with another module.
The terms driver, module, Ethernet frame, IP packet, UDP datagram,
TCP message, and application message are used where appropriate
throughout this tutorial.
<span class="h3"><a class="selflink" id="section-2.3" href="#section-2.3">2.3</a> Flow of Data</span>
Let's follow the data as it flows down through the protocol stack
shown in Figure 1. For an application that uses TCP (Transmission
Control Protocol), data passes between the application and the TCP
module. For applications that use UDP (User Datagram Protocol), data
passes between the application and the UDP module. FTP (File
Transfer Protocol) is a typical application that uses TCP. Its
protocol stack in this example is FTP/TCP/IP/ENET. SNMP (Simple
Network Management Protocol) is an application that uses UDP. Its
protocol stack in this example is SNMP/UDP/IP/ENET.
The TCP module, UDP module, and the Ethernet driver are n-to-1
multiplexers. As multiplexers they switch many inputs to one output.
They are also 1-to-n de-multiplexers. As de-multiplexers they switch
one input to many outputs according to the type field in the protocol
header.
<span class="grey">Socolofsky & Kale [Page 3]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-4" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
1 2 3 ... n 1 2 3 ... n
\ | / | \ | | / ^
\ | | / | \ | | / |
------------- flow ---------------- flow
|multiplexer| of |de-multiplexer| of
------------- data ---------------- data
| | | |
| v | |
1 1
Figure 2. n-to-1 multiplexer and 1-to-n de-multiplexer
If an Ethernet frame comes up into the Ethernet driver off the
network, the packet can be passed upwards to either the ARP (Address
Resolution Protocol) module or to the IP (Internet Protocol) module.
The value of the type field in the Ethernet frame determines whether
the Ethernet frame is passed to the ARP or the IP module.
If an IP packet comes up into IP, the unit of data is passed upwards
to either TCP or UDP, as determined by the value of the protocol
field in the IP header.
If the UDP datagram comes up into UDP, the application message is
passed upwards to the network application based on the value of the
port field in the UDP header. If the TCP message comes up into TCP,
the application message is passed upwards to the network application
based on the value of the port field in the TCP header.
The downwards multiplexing is simple to perform because from each
starting point there is only the one downward path; each protocol
module adds its header information so the packet can be de-
multiplexed at the destination computer.
Data passing out from the applications through either TCP or UDP
converges on the IP module and is sent downwards through the lower
network interface driver.
Although internet technology supports many different network media,
Ethernet is used for all examples in this tutorial because it is the
most common physical network used under IP. The computer in Figure 1
has a single Ethernet connection. The 6-byte Ethernet address is
unique for each interface on an Ethernet and is located at the lower
interface of the Ethernet driver.
The computer also has a 4-byte IP address. This address is located
at the lower interface to the IP module. The IP address must be
unique for an internet.
<span class="grey">Socolofsky & Kale [Page 4]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-5" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
A running computer always knows its own IP address and Ethernet
address.
<span class="h3"><a class="selflink" id="section-2.4" href="#section-2.4">2.4</a> Two Network Interfaces</span>
If a computer is connected to 2 separate Ethernets it is as in Figure
3.
----------------------------
| network applications |
| |
|... \ | / .. \ | / ...|
| ----- ----- |
| |TCP| |UDP| |
| ----- ----- |
| \ / |
| -------- |
| | IP | |
| ----- -*----*- ----- |
| |ARP| | | |ARP| |
| ----- | | ----- |
| \ | | / |
| ------ ------ |
| |ENET| |ENET| |
| ---@-- ---@-- |
----------|-------|---------
| |
| ---o---------------------------
| Ethernet Cable 2
---------------o----------
Ethernet Cable 1
Figure 3. TCP/IP Network Node on 2 Ethernets
Please note that this computer has 2 Ethernet addresses and 2 IP
addresses.
It is seen from this structure that for computers with more than one
physical network interface, the IP module is both a n-to-m
multiplexer and an m-to-n de-multiplexer.
<span class="grey">Socolofsky & Kale [Page 5]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-6" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
1 2 3 ... n 1 2 3 ... n
\ | | / | \ | | / ^
\ | | / | \ | | / |
------------- flow ---------------- flow
|multiplexer| of |de-multiplexer| of
------------- data ---------------- data
/ | | \ | / | | \ |
/ | | \ v / | | \ |
1 2 3 ... m 1 2 3 ... m
Figure 4. n-to-m multiplexer and m-to-n de-multiplexer
It performs this multiplexing in either direction to accommodate
incoming and outgoing data. An IP module with more than 1 network
interface is more complex than our original example in that it can
forward data onto the next network. Data can arrive on any network
interface and be sent out on any other.
TCP UDP
\ /
\ /
--------------
| IP |
| |
| --- |
| / \ |
| / v |
--------------
/ \
/ \
data data
comes in goes out
here here
Figure 5. Example of IP Forwarding a IP Packet
The process of sending an IP packet out onto another network is
called "forwarding" an IP packet. A computer that has been dedicated
to the task of forwarding IP packets is called an "IP-router".
As you can see from the figure, the forwarded IP packet never touches
the TCP and UDP modules on the IP-router. Some IP-router
implementations do not have a TCP or UDP module.
<span class="h3"><a class="selflink" id="section-2.5" href="#section-2.5">2.5</a> IP Creates a Single Logical Network</span>
The IP module is central to the success of internet technology. Each
module or driver adds its header to the message as the message passes
<span class="grey">Socolofsky & Kale [Page 6]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-7" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
down through the protocol stack. Each module or driver strips the
corresponding header from the message as the message climbs the
protocol stack up towards the application. The IP header contains
the IP address, which builds a single logical network from multiple
physical networks. This interconnection of physical networks is the
source of the name: internet. A set of interconnected physical
networks that limit the range of an IP packet is called an
"internet".
<span class="h3"><a class="selflink" id="section-2.6" href="#section-2.6">2.6</a> Physical Network Independence</span>
IP hides the underlying network hardware from the network
applications. If you invent a new physical network, you can put it
into service by implementing a new driver that connects to the
internet underneath IP. Thus, the network applications remain intact
and are not vulnerable to changes in hardware technology.
<span class="h3"><a class="selflink" id="section-2.7" href="#section-2.7">2.7</a> Interoperability</span>
If two computers on an internet can communicate, they are said to
"interoperate"; if an implementation of internet technology is good,
it is said to have "interoperability". Users of general-purpose
computers benefit from the installation of an internet because of the
interoperability in computers on the market. Generally, when you buy
a computer, it will interoperate. If the computer does not have
interoperability, and interoperability can not be added, it occupies
a rare and special niche in the market.
<span class="h3"><a class="selflink" id="section-2.8" href="#section-2.8">2.8</a> After the Overview</span>
With the background set, we will answer the following questions:
When sending out an IP packet, how is the destination Ethernet
address determined?
How does IP know which of multiple lower network interfaces to use
when sending out an IP packet?
How does a client on one computer reach the server on another?
Why do both TCP and UDP exist, instead of just one or the other?
What network applications are available?
These will be explained, in turn, after an Ethernet refresher.
<span class="grey">Socolofsky & Kale [Page 7]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-8" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
<span class="h2"><a class="selflink" id="section-3" href="#section-3">3</a>. Ethernet</span>
This section is a short review of Ethernet technology.
An Ethernet frame contains the destination address, source address,
type field, and data.
An Ethernet address is 6 bytes. Every device has its own Ethernet
address and listens for Ethernet frames with that destination
address. All devices also listen for Ethernet frames with a wild-
card destination address of "FF-FF-FF-FF-FF-FF" (in hexadecimal),
called a "broadcast" address.
Ethernet uses CSMA/CD (Carrier Sense and Multiple Access with
Collision Detection). CSMA/CD means that all devices communicate on
a single medium, that only one can transmit at a time, and that they
can all receive simultaneously. If 2 devices try to transmit at the
same instant, the transmit collision is detected, and both devices
wait a random (but short) period before trying to transmit again.
<span class="h3"><a class="selflink" id="section-3.1" href="#section-3.1">3.1</a> A Human Analogy</span>
A good analogy of Ethernet technology is a group of people talking in
a small, completely dark room. In this analogy, the physical network
medium is sound waves on air in the room instead of electrical
signals on a coaxial cable.
Each person can hear the words when another is talking (Carrier
Sense). Everyone in the room has equal capability to talk (Multiple
Access), but none of them give lengthy speeches because they are
polite. If a person is impolite, he is asked to leave the room
(i.e., thrown off the net).
No one talks while another is speaking. But if two people start
speaking at the same instant, each of them know this because each
hears something they haven't said (Collision Detection). When these
two people notice this condition, they wait for a moment, then one
begins talking. The other hears the talking and waits for the first
to finish before beginning his own speech.
Each person has an unique name (unique Ethernet address) to avoid
confusion. Every time one of them talks, he prefaces the message
with the name of the person he is talking to and with his own name
(Ethernet destination and source address, respectively), i.e., "Hello
Jane, this is Jack, ..blah blah blah...". If the sender wants to
talk to everyone he might say "everyone" (broadcast address), i.e.,
"Hello Everyone, this is Jack, ..blah blah blah...".
<span class="grey">Socolofsky & Kale [Page 8]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-9" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
<span class="h2"><a class="selflink" id="section-4" href="#section-4">4</a>. ARP</span>
When sending out an IP packet, how is the destination Ethernet
address determined?
ARP (Address Resolution Protocol) is used to translate IP addresses
to Ethernet addresses. The translation is done only for outgoing IP
packets, because this is when the IP header and the Ethernet header
are created.
<span class="h3"><a class="selflink" id="section-4.1" href="#section-4.1">4.1</a> ARP Table for Address Translation</span>
The translation is performed with a table look-up. The table, called
the ARP table, is stored in memory and contains a row for each
computer. There is a column for IP address and a column for Ethernet
address. When translating an IP address to an Ethernet address, the
table is searched for a matching IP address. The following is a
simplified ARP table:
------------------------------------
|IP address Ethernet address |
------------------------------------
|223.1.2.1 08-00-39-00-2F-C3|
|223.1.2.3 08-00-5A-21-A7-22|
|223.1.2.4 08-00-10-99-AC-54|
------------------------------------
TABLE 1. Example ARP Table
The human convention when writing out the 4-byte IP address is each
byte in decimal and separating bytes with a period. When writing out
the 6-byte Ethernet address, the conventions are each byte in
hexadecimal and separating bytes with either a minus sign or a colon.
The ARP table is necessary because the IP address and Ethernet
address are selected independently; you can not use an algorithm to
translate IP address to Ethernet address. The IP address is selected
by the network manager based on the location of the computer on the
internet. When the computer is moved to a different part of an
internet, its IP address must be changed. The Ethernet address is
selected by the manufacturer based on the Ethernet address space
licensed by the manufacturer. When the Ethernet hardware interface
board changes, the Ethernet address changes.
<span class="h3"><a class="selflink" id="section-4.2" href="#section-4.2">4.2</a> Typical Translation Scenario</span>
During normal operation a network application, such as TELNET, sends
an application message to TCP, then TCP sends the corresponding TCP
message to the IP module. The destination IP address is known by the
<span class="grey">Socolofsky & Kale [Page 9]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-10" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
application, the TCP module, and the IP module. At this point the IP
packet has been constructed and is ready to be given to the Ethernet
driver, but first the destination Ethernet address must be
determined.
The ARP table is used to look-up the destination Ethernet address.
4.3 ARP Request/Response Pair
But how does the ARP table get filled in the first place? The answer
is that it is filled automatically by ARP on an "as-needed" basis.
Two things happen when the ARP table can not be used to translate an
address:
1. An ARP request packet with a broadcast Ethernet address is sent
out on the network to every computer.
2. The outgoing IP packet is queued.
Every computer's Ethernet interface receives the broadcast Ethernet
frame. Each Ethernet driver examines the Type field in the Ethernet
frame and passes the ARP packet to the ARP module. The ARP request
packet says "If your IP address matches this target IP address, then
please tell me your Ethernet address". An ARP request packet looks
something like this:
---------------------------------------
|Sender IP Address 223.1.2.1 |
|Sender Enet Address 08-00-39-00-2F-C3|
---------------------------------------
|Target IP Address 223.1.2.2 |
|Target Enet Address <blank> |
---------------------------------------
TABLE 2. Example ARP Request
Each ARP module examines the IP address and if the Target IP address
matches its own IP address, it sends a response directly to the
source Ethernet address. The ARP response packet says "Yes, that
target IP address is mine, let me give you my Ethernet address". An
ARP response packet has the sender/target field contents swapped as
compared to the request. It looks something like this:
<span class="grey">Socolofsky & Kale [Page 10]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-11" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
---------------------------------------
|Sender IP Address 223.1.2.2 |
|Sender Enet Address 08-00-28-00-38-A9|
---------------------------------------
|Target IP Address 223.1.2.1 |
|Target Enet Address 08-00-39-00-2F-C3|
---------------------------------------
TABLE 3. Example ARP Response
The response is received by the original sender computer. The
Ethernet driver looks at the Type field in the Ethernet frame then
passes the ARP packet to the ARP module. The ARP module examines the
ARP packet and adds the sender's IP and Ethernet addresses to its ARP
table.
The updated table now looks like this:
----------------------------------
|IP address Ethernet address |
----------------------------------
|223.1.2.1 08-00-39-00-2F-C3|
|223.1.2.2 08-00-28-00-38-A9|
|223.1.2.3 08-00-5A-21-A7-22|
|223.1.2.4 08-00-10-99-AC-54|
----------------------------------
TABLE 4. ARP Table after Response
<span class="h3"><a class="selflink" id="section-4.4" href="#section-4.4">4.4</a> Scenario Continued</span>
The new translation has now been installed automatically in the
table, just milli-seconds after it was needed. As you remember from
step 2 above, the outgoing IP packet was queued. Next, the IP
address to Ethernet address translation is performed by look-up in
the ARP table then the Ethernet frame is transmitted on the Ethernet.
Therefore, with the new steps 3, 4, and 5, the scenario for the
sender computer is:
1. An ARP request packet with a broadcast Ethernet address is sent
out on the network to every computer.
2. The outgoing IP packet is queued.
3. The ARP response arrives with the IP-to-Ethernet address
translation for the ARP table.
<span class="grey">Socolofsky & Kale [Page 11]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-12" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
4. For the queued IP packet, the ARP table is used to translate the
IP address to the Ethernet address.
5. The Ethernet frame is transmitted on the Ethernet.
In summary, when the translation is missing from the ARP table, one
IP packet is queued. The translation data is quickly filled in with
ARP request/response and the queued IP packet is transmitted.
Each computer has a separate ARP table for each of its Ethernet
interfaces. If the target computer does not exist, there will be no
ARP response and no entry in the ARP table. IP will discard outgoing
IP packets sent to that address. The upper layer protocols can't
tell the difference between a broken Ethernet and the absence of a
computer with the target IP address.
Some implementations of IP and ARP don't queue the IP packet while
waiting for the ARP response. Instead the IP packet is discarded and
the recovery from the IP packet loss is left to the TCP module or the
UDP network application. This recovery is performed by time-out and
retransmission. The retransmitted message is successfully sent out
onto the network because the first copy of the message has already
caused the ARP table to be filled.
<span class="h2"><a class="selflink" id="section-5" href="#section-5">5</a>. Internet Protocol</span>
The IP module is central to internet technology and the essence of IP
is its route table. IP uses this in-memory table to make all
decisions about routing an IP packet. The content of the route table
is defined by the network administrator. Mistakes block
communication.
To understand how a route table is used is to understand
internetworking. This understanding is necessary for the successful
administration and maintenance of an IP network.
The route table is best understood by first having an overview of
routing, then learning about IP network addresses, and then looking
at the details.
<span class="h3"><a class="selflink" id="section-5.1" href="#section-5.1">5.1</a> Direct Routing</span>
The figure below is of a tiny internet with 3 computers: A, B, and C.
Each computer has the same TCP/IP protocol stack as in Figure 1.
Each computer's Ethernet interface has its own Ethernet address.
Each computer has an IP address assigned to the IP interface by the
network manager, who also has assigned an IP network number to the
Ethernet.
<span class="grey">Socolofsky & Kale [Page 12]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-13" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
A B C
| | |
--o------o------o--
Ethernet 1
IP network "development"
Figure 6. One IP Network
When A sends an IP packet to B, the IP header contains A's IP address
as the source IP address, and the Ethernet header contains A's
Ethernet address as the source Ethernet address. Also, the IP header
contains B's IP address as the destination IP address and the
Ethernet header contains B's Ethernet address as the destination
Ethernet address.
----------------------------------------
|address source destination|
----------------------------------------
|IP header A B |
|Ethernet header A B |
----------------------------------------
TABLE 5. Addresses in an Ethernet frame for an IP packet
from A to B
For this simple case, IP is overhead because the IP adds little to
the service offered by Ethernet. However, IP does add cost: the
extra CPU processing and network bandwidth to generate, transmit, and
parse the IP header.
When B's IP module receives the IP packet from A, it checks the
destination IP address against its own, looking for a match, then it
passes the datagram to the upper-level protocol.
This communication between A and B uses direct routing.
<span class="h3"><a class="selflink" id="section-5.2" href="#section-5.2">5.2</a> Indirect Routing</span>
The figure below is a more realistic view of an internet. It is
composed of 3 Ethernets and 3 IP networks connected by an IP-router
called computer D. Each IP network has 4 computers; each computer
has its own IP address and Ethernet address.
<span class="grey">Socolofsky & Kale [Page 13]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-14" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
A B C ----D---- E F G
| | | | | | | | |
--o------o------o------o- | -o------o------o------o--
Ethernet 1 | Ethernet 2
IP network "development" | IP network "accounting"
|
|
| H I J
| | | |
--o-----o------o------o--
Ethernet 3
IP network "factory"
Figure 7. Three IP Networks; One internet
Except for computer D, each computer has a TCP/IP protocol stack like
that in Figure 1. Computer D is the IP-router; it is connected to
all 3 networks and therefore has 3 IP addresses and 3 Ethernet
addresses. Computer D has a TCP/IP protocol stack similar to that in
Figure 3, except that it has 3 ARP modules and 3 Ethernet drivers
instead of 2. Please note that computer D has only one IP module.
The network manager has assigned a unique number, called an IP
network number, to each of the Ethernets. The IP network numbers are
not shown in this diagram, just the network names.
When computer A sends an IP packet to computer B, the process is
identical to the single network example above. Any communication
between computers located on a single IP network matches the direct
routing example discussed previously.
When computer D and A communicate, it is direct communication. When
computer D and E communicate, it is direct communication. When
computer D and H communicate, it is direct communication. This is
because each of these pairs of computers is on the same IP network.
However, when computer A communicates with a computer on the far side
of the IP-router, communication is no longer direct. A must use D to
forward the IP packet to the next IP network. This communication is
called "indirect".
This routing of IP packets is done by IP modules and happens
transparently to TCP, UDP, and the network applications.
If A sends an IP packet to E, the source IP address and the source
Ethernet address are A's. The destination IP address is E's, but
because A's IP module sends the IP packet to D for forwarding, the
destination Ethernet address is D's.
<span class="grey">Socolofsky & Kale [Page 14]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-15" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
----------------------------------------
|address source destination|
----------------------------------------
|IP header A E |
|Ethernet header A D |
----------------------------------------
TABLE 6. Addresses in an Ethernet frame for an IP packet
from A to E (before D)
D's IP module receives the IP packet and upon examining the
destination IP address, says "This is not my IP address," and sends
the IP packet directly to E.
----------------------------------------
|address source destination|
----------------------------------------
|IP header A E |
|Ethernet header D E |
----------------------------------------
TABLE 7. Addresses in an Ethernet frame for an IP packet
from A to E (after D)
In summary, for direct communication, both the source IP address and
the source Ethernet address is the sender's, and the destination IP
address and the destination Ethernet address is the recipient's. For
indirect communication, the IP address and Ethernet addresses do not
pair up in this way.
This example internet is a very simple one. Real networks are often
complicated by many factors, resulting in multiple IP-routers and
several types of physical networks. This example internet might have
come about because the network manager wanted to split a large
Ethernet in order to localize Ethernet broadcast traffic.
<span class="h3"><a class="selflink" id="section-5.3" href="#section-5.3">5.3</a> IP Module Routing Rules</span>
This overview of routing has shown what happens, but not how it
happens. Now let's examine the rules, or algorithm, used by the IP
module.
For an outgoing IP packet, entering IP from an upper layer, IP must
decide whether to send the IP packet directly or indirectly, and IP
must choose a lower network interface. These choices are made by
consulting the route table.
For an incoming IP packet, entering IP from a lower interface, IP
must decide whether to forward the IP packet or pass it to an upper
layer. If the IP packet is being forwarded, it is treated as an
<span class="grey">Socolofsky & Kale [Page 15]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-16" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
outgoing IP packet.
When an incoming IP packet arrives it is never forwarded back out
through the same network interface.
These decisions are made before the IP packet is handed to the lower
interface and before the ARP table is consulted.
<span class="h3"><a class="selflink" id="section-5.4" href="#section-5.4">5.4</a> IP Address</span>
The network manager assigns IP addresses to computers according to
the IP network to which the computer is attached. One part of a 4-
byte IP address is the IP network number, the other part is the IP
computer number (or host number). For the computer in table 1, with
an IP address of 223.1.2.1, the network number is 223.1.2 and the
host number is number 1.
The portion of the address that is used for network number and for
host number is defined by the upper bits in the 4-byte address. All
example IP addresses in this tutorial are of type class C, meaning
that the upper 3 bits indicate that 21 bits are the network number
and 8 bits are the host number. This allows 2,097,152 class C
networks up to 254 hosts on each network.
The IP address space is administered by the NIC (Network Information
Center). All internets that are connected to the single world-wide
Internet must use network numbers assigned by the NIC. If you are
setting up your own internet and you are not intending to connect it
to the Internet, you should still obtain your network numbers from
the NIC. If you pick your own number, you run the risk of confusion
and chaos in the eventuality that your internet is connected to
another internet.
<span class="h3"><a class="selflink" id="section-5.5" href="#section-5.5">5.5</a> Names</span>
People refer to computers by names, not numbers. A computer called
alpha might have the IP address of 223.1.2.1. For small networks,
this name-to-address translation data is often kept on each computer
in the "hosts" file. For larger networks, this translation data file
is stored on a server and accessed across the network when needed. A
few lines from that file might look like this:
223.1.2.1 alpha
223.1.2.2 beta
223.1.2.3 gamma
223.1.2.4 delta
223.1.3.2 epsilon
223.1.4.2 iota
<span class="grey">Socolofsky & Kale [Page 16]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-17" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
The IP address is the first column and the computer name is the
second column.
In most cases, you can install identical "hosts" files on all
computers. You may notice that "delta" has only one entry in this
file even though it has 3 IP addresses. Delta can be reached with
any of its IP addresses; it does not matter which one is used. When
delta receives an IP packet and looks at the destination address, it
will recognize any of its own IP addresses.
IP networks are also given names. If you have 3 IP networks, your
"networks" file for documenting these names might look something like
this:
223.1.2 development
223.1.3 accounting
223.1.4 factory
The IP network number is in the first column and its name is in the
second column.
From this example you can see that alpha is computer number 1 on the
development network, beta is computer number 2 on the development
network and so on. You might also say that alpha is development.1,
Beta is development.2, and so on.
The above hosts file is adequate for the users, but the network
manager will probably replace the line for delta with:
223.1.2.4 devnetrouter delta
223.1.3.1 facnetrouter
223.1.4.1 accnetrouter
These three new lines for the hosts file give each of delta's IP
addresses a meaningful name. In fact, the first IP address listed
has 2 names; "delta" and "devnetrouter" are synonyms. In practice
"delta" is the general-purpose name of the computer and the other 3
names are only used when administering the IP route table.
These files are used by network administration commands and network
applications to provide meaningful names. They are not required for
operation of an internet, but they do make it easier for us.
<span class="h3"><a class="selflink" id="section-5.6" href="#section-5.6">5.6</a> IP Route Table</span>
How does IP know which lower network interface to use when sending
out a IP packet? IP looks it up in the route table using a search
key of the IP network number extracted from the IP destination
<span class="grey">Socolofsky & Kale [Page 17]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-18" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
address.
The route table contains one row for each route. The primary columns
in the route table are: IP network number, direct/indirect flag,
router IP address, and interface number. This table is referred to
by IP for each outgoing IP packet.
On most computers the route table can be modified with the "route"
command. The content of the route table is defined by the network
manager, because the network manager assigns the IP addresses to the
computers.
<span class="h3"><a class="selflink" id="section-5.7" href="#section-5.7">5.7</a> Direct Routing Details</span>
To explain how it is used, let us visit in detail the routing
situations we have reviewed previously.
--------- ---------
| alpha | | beta |
| 1 | | 1 |
--------- ---------
| |
--------o---------------o-
Ethernet 1
IP network "development"
Figure 8. Close-up View of One IP Network
The route table inside alpha looks like this:
--------------------------------------------------------------
|network direct/indirect flag router interface number|
--------------------------------------------------------------
|development direct <blank> 1 |
--------------------------------------------------------------
TABLE 8. Example Simple Route Table
This view can be seen on some UNIX systems with the "netstat -r"
command. With this simple network, all computers have identical
routing tables.
For discussion, the table is printed again without the network number
translated to its network name.
<span class="grey">Socolofsky & Kale [Page 18]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-19" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
--------------------------------------------------------------
|network direct/indirect flag router interface number|
--------------------------------------------------------------
|223.1.2 direct <blank> 1 |
--------------------------------------------------------------
TABLE 9. Example Simple Route Table with Numbers
<span class="h3"><a class="selflink" id="section-5.8" href="#section-5.8">5.8</a> Direct Scenario</span>
Alpha is sending an IP packet to beta. The IP packet is in alpha's
IP module and the destination IP address is beta or 223.1.2.2. IP
extracts the network portion of this IP address and scans the first
column of the table looking for a match. With this network a match
is found on the first entry.
The other information in this entry indicates that computers on this
network can be reached directly through interface number 1. An ARP
table translation is done on beta's IP address then the Ethernet
frame is sent directly to beta via interface number 1.
If an application tries to send data to an IP address that is not on
the development network, IP will be unable to find a match in the
route table. IP then discards the IP packet. Some computers provide
a "Network not reachable" error message.
<span class="h3"><a class="selflink" id="section-5.9" href="#section-5.9">5.9</a> Indirect Routing Details</span>
Now, let's take a closer look at the more complicated routing
scenario that we examined previously.
<span class="grey">Socolofsky & Kale [Page 19]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-20" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
--------- --------- ---------
| alpha | | delta | |epsilon|
| 1 | |1 2 3| | 1 |
--------- --------- ---------
| | | | |
--------o---------------o- | -o----------------o--------
Ethernet 1 | Ethernet 2
IP network "Development" | IP network "accounting"
|
| --------
| | iota |
| | 1 |
| --------
| |
--o--------o--------
Ethernet 3
IP network "factory"
Figure 9. Close-up View of Three IP Networks
The route table inside alpha looks like this:
---------------------------------------------------------------------
|network direct/indirect flag router interface number|
---------------------------------------------------------------------
|development direct <blank> 1 |
|accounting indirect devnetrouter 1 |
|factory indirect devnetrouter 1 |
---------------------------------------------------------------------
TABLE 10. Alpha Route Table
For discussion the table is printed again using numbers instead of
names.
--------------------------------------------------------------------
|network direct/indirect flag router interface number|
--------------------------------------------------------------------
|223.1.2 direct <blank> 1 |
|223.1.3 indirect 223.1.2.4 1 |
|223.1.4 indirect 223.1.2.4 1 |
--------------------------------------------------------------------
TABLE 11. Alpha Route Table with Numbers
The router in Alpha's route table is the IP address of delta's
connection to the development network.
<span class="grey">Socolofsky & Kale [Page 20]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-21" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
<span class="h3"><a class="selflink" id="section-5.10" href="#section-5.10">5.10</a> Indirect Scenario</span>
Alpha is sending an IP packet to epsilon. The IP packet is in
alpha's IP module and the destination IP address is epsilon
(223.1.3.2). IP extracts the network portion of this IP address
(223.1.3) and scans the first column of the table looking for a
match. A match is found on the second entry.
This entry indicates that computers on the 223.1.3 network can be
reached through the IP-router devnetrouter. Alpha's IP module then
does an ARP table translation for devnetrouter's IP address and sends
the IP packet directly to devnetrouter through Alpha's interface
number 1. The IP packet still contains the destination address of
epsilon.
The IP packet arrives at delta's development network interface and is
passed up to delta's IP module. The destination IP address is
examined and because it does not match any of delta's own IP
addresses, delta decides to forward the IP packet.
Delta's IP module extracts the network portion of the destination IP
address (223.1.3) and scans its route table for a matching network
field. Delta's route table looks like this:
----------------------------------------------------------------------
|network direct/indirect flag router interface number|
----------------------------------------------------------------------
|development direct <blank> 1 |
|factory direct <blank> 3 |
|accounting direct <blank> 2 |
----------------------------------------------------------------------
TABLE 12. Delta's Route Table
Below is delta's table printed again, without the translation to
names.
----------------------------------------------------------------------
|network direct/indirect flag router interface number|
----------------------------------------------------------------------
|223.1.2 direct <blank> 1 |
|223.1.3 direct <blank> 3 |
|223.1.4 direct <blank> 2 |
----------------------------------------------------------------------
TABLE 13. Delta's Route Table with Numbers
The match is found on the second entry. IP then sends the IP packet
directly to epsilon through interface number 3. The IP packet
contains the IP destination address of epsilon and the Ethernet
<span class="grey">Socolofsky & Kale [Page 21]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-22" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
destination address of epsilon.
The IP packet arrives at epsilon and is passed up to epsilon's IP
module. The destination IP address is examined and found to match
with epsilon's IP address, so the IP packet is passed to the upper
protocol layer.
<span class="h3"><a class="selflink" id="section-5.11" href="#section-5.11">5.11</a> Routing Summary</span>
When a IP packet travels through a large internet it may go through
many IP-routers before it reaches its destination. The path it takes
is not determined by a central source but is a result of consulting
each of the routing tables used in the journey. Each computer
defines only the next hop in the journey and relies on that computer
to send the IP packet on its way.
<span class="h3"><a class="selflink" id="section-5.12" href="#section-5.12">5.12</a> Managing the Routes</span>
Maintaining correct routing tables on all computers in a large
internet is a difficult task; network configuration is being modified
constantly by the network managers to meet changing needs. Mistakes
in routing tables can block communication in ways that are
excruciatingly tedious to diagnose.
Keeping a simple network configuration goes a long way towards making
a reliable internet. For instance, the most straightforward method
of assigning IP networks to Ethernet is to assign a single IP network
number to each Ethernet.
Help is also available from certain protocols and network
applications. ICMP (Internet Control Message Protocol) can report
some routing problems. For small networks the route table is filled
manually on each computer by the network administrator. For larger
networks the network administrator automates this manual operation
with a routing protocol to distribute routes throughout a network.
When a computer is moved from one IP network to another, its IP
address must change. When a computer is removed from an IP network
its old address becomes invalid. These changes require frequent
updates to the "hosts" file. This flat file can become difficult to
maintain for even medium-size networks. The Domain Name System helps
solve these problems.
<span class="h2"><a class="selflink" id="section-6" href="#section-6">6</a>. User Datagram Protocol</span>
UDP is one of the two main protocols to reside on top of IP. It
offers service to the user's network applications. Example network
applications that use UDP are: Network File System (NFS) and Simple
<span class="grey">Socolofsky & Kale [Page 22]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-23" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
Network Management Protocol (SNMP). The service is little more than
an interface to IP.
UDP is a connectionless datagram delivery service that does not
guarantee delivery. UDP does not maintain an end-to-end connection
with the remote UDP module; it merely pushes the datagram out on the
net and accepts incoming datagrams off the net.
UDP adds two values to what is provided by IP. One is the
multiplexing of information between applications based on port
number. The other is a checksum to check the integrity of the data.
<span class="h3"><a class="selflink" id="section-6.1" href="#section-6.1">6.1</a> Ports</span>
How does a client on one computer reach the server on another?
The path of communication between an application and UDP is through
UDP ports. These ports are numbered, beginning with zero. An
application that is offering service (the server) waits for messages
to come in on a specific port dedicated to that service. The server
waits patiently for any client to request service.
For instance, the SNMP server, called an SNMP agent, always waits on
port 161. There can be only one SNMP agent per computer because
there is only one UDP port number 161. This port number is well
known; it is a fixed number, an internet assigned number. If an SNMP
client wants service, it sends its request to port number 161 of UDP
on the destination computer.
When an application sends data out through UDP it arrives at the far
end as a single unit. For example, if an application does 5 writes
to the UDP port, the application at the far end will do 5 reads from
the UDP port. Also, the size of each write matches the size of each
read.
UDP preserves the message boundary defined by the application. It
never joins two application messages together, or divides a single
application message into parts.
<span class="h3"><a class="selflink" id="section-6.2" href="#section-6.2">6.2</a> Checksum</span>
An incoming IP packet with an IP header type field indicating "UDP"
is passed up to the UDP module by IP. When the UDP module receives
the UDP datagram from IP it examines the UDP checksum. If the
checksum is zero, it means that checksum was not calculated by the
sender and can be ignored. Thus the sending computer's UDP module
may or may not generate checksums. If Ethernet is the only network
between the 2 UDP modules communicating, then you may not need
<span class="grey">Socolofsky & Kale [Page 23]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-24" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
checksumming. However, it is recommended that checksum generation
always be enabled because at some point in the future a route table
change may send the data across less reliable media.
If the checksum is valid (or zero), the destination port number is
examined and if an application is bound to that port, an application
message is queued for the application to read. Otherwise the UDP
datagram is discarded. If the incoming UDP datagrams arrive faster
than the application can read them and if the queue fills to a
maximum value, UDP datagrams are discarded by UDP. UDP will continue
to discard UDP datagrams until there is space in the queue.
<span class="h2"><a class="selflink" id="section-7" href="#section-7">7</a>. Transmission Control Protocol</span>
TCP provides a different service than UDP. TCP offers a connection-
oriented byte stream, instead of a connectionless datagram delivery
service. TCP guarantees delivery, whereas UDP does not.
TCP is used by network applications that require guaranteed delivery
and cannot be bothered with doing time-outs and retransmissions. The
two most typical network applications that use TCP are File Transfer
Protocol (FTP) and the TELNET. Other popular TCP network
applications include X-Window System, rcp (remote copy), and the r-
series commands. TCP's greater capability is not without cost: it
requires more CPU and network bandwidth. The internals of the TCP
module are much more complicated than those in a UDP module.
Similar to UDP, network applications connect to TCP ports. Well-
defined port numbers are dedicated to specific applications. For
instance, the TELNET server uses port number 23. The TELNET client
can find the server simply by connecting to port 23 of TCP on the
specified computer.
When the application first starts using TCP, the TCP module on the
client's computer and the TCP module on the server's computer start
communicating with each other. These two end-point TCP modules
contain state information that defines a virtual circuit. This
virtual circuit consumes resources in both TCP end-points. The
virtual circuit is full duplex; data can go in both directions
simultaneously. The application writes data to the TCP port, the
data traverses the network and is read by the application at the far
end.
TCP packetizes the byte stream at will; it does not retain the
boundaries between writes. For example, if an application does 5
writes to the TCP port, the application at the far end might do 10
reads to get all the data. Or it might get all the data with a
single read. There is no correlation between the number and size of
<span class="grey">Socolofsky & Kale [Page 24]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-25" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
writes at one end to the number and size of reads at the other end.
TCP is a sliding window protocol with time-out and retransmits.
Outgoing data must be acknowledged by the far-end TCP.
Acknowledgements can be piggybacked on data. Both receiving ends can
flow control the far end, thus preventing a buffer overrun.
As with all sliding window protocols, the protocol has a window size.
The window size determines the amount of data that can be transmitted
before an acknowledgement is required. For TCP, this amount is not a
number of TCP segments but a number of bytes.
<span class="h2"><a class="selflink" id="section-8" href="#section-8">8</a>. Network Applications</span>
Why do both TCP and UDP exist, instead of just one or the other?
They supply different services. Most applications are implemented to
use only one or the other. You, the programmer, choose the protocol
that best meets your needs. If you need a reliable stream delivery
service, TCP might be best. If you need a datagram service, UDP
might be best. If you need efficiency over long-haul circuits, TCP
might be best. If you need efficiency over fast networks with short
latency, UDP might be best. If your needs do not fall nicely into
these categories, then the "best" choice is unclear. However,
applications can make up for deficiencies in the choice. For
instance if you choose UDP and you need reliability, then the
application must provide reliability. If you choose TCP and you need
a record oriented service, then the application must insert markers
in the byte stream to delimit records.
What network applications are available?
There are far too many to list. The number is growing continually.
Some of the applications have existed since the beginning of internet
technology: TELNET and FTP. Others are relatively new: X-Windows and
SNMP. The following is a brief description of the applications
mentioned in this tutorial.
<span class="h3"><a class="selflink" id="section-8.1" href="#section-8.1">8.1</a> TELNET</span>
TELNET provides a remote login capability on TCP. The operation and
appearance is similar to keyboard dialing through a telephone switch.
On the command line the user types "telnet delta" and receives a
login prompt from the computer called "delta".
TELNET works well; it is an old application and has widespread
interoperability. Implementations of TELNET usually work between
different operating systems. For instance, a TELNET client may be on
<span class="grey">Socolofsky & Kale [Page 25]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-26" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
VAX/VMS and the server on UNIX System V.
<span class="h3"><a class="selflink" id="section-8.2" href="#section-8.2">8.2</a> FTP</span>
File Transfer Protocol (FTP), as old as TELNET, also uses TCP and has
widespread interoperability. The operation and appearance is as if
you TELNETed to the remote computer. But instead of typing your
usual commands, you have to make do with a short list of commands for
directory listings and the like. FTP commands allow you to copy
files between computers.
<span class="h3"><a class="selflink" id="section-8.3" href="#section-8.3">8.3</a> rsh</span>
Remote shell (rsh or remsh) is one of an entire family of remote UNIX
style commands. The UNIX copy command, cp, becomes rcp. The UNIX
"who is logged in" command, who, becomes rwho. The list continues
and is referred to collectively to as the "r" series commands or the
"r*" (r star) commands.
The r* commands mainly work between UNIX systems and are designed for
interaction between trusted hosts. Little consideration is given to
security, but they provide a convenient user environment.
To execute the "cc file.c" command on a remote computer called delta,
type "rsh delta cc file.c". To copy the "file.c" file to delta, type
"rcp file.c delta:". To login to delta, type "rlogin delta", and if
you administered the computers in a certain way, you will not be
challenged with a password prompt.
<span class="h3"><a class="selflink" id="section-8.4" href="#section-8.4">8.4</a> NFS</span>
Network File System, first developed by Sun Microsystems Inc, uses
UDP and is excellent for mounting UNIX file systems on multiple
computers. A diskless workstation can access its server's hard disk
as if the disk were local to the workstation. A single disk copy of
a database on mainframe "alpha" can also be used by mainframe "beta"
if the database's file system is NFS mounted on "beta".
NFS adds significant load to a network and has poor utility across
slow links, but the benefits are strong. The NFS client is
implemented in the kernel, allowing all applications and commands to
use the NFS mounted disk as if it were local disk.
<span class="h3"><a class="selflink" id="section-8.5" href="#section-8.5">8.5</a> SNMP</span>
Simple Network Management Protocol (SNMP) uses UDP and is designed
for use by central network management stations. It is a well known
fact that if given enough data, a network manager can detect and
<span class="grey">Socolofsky & Kale [Page 26]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-27" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
diagnose network problems. The central station uses SNMP to collect
this data from other computers on the network. SNMP defines the
format for the data; it is left to the central station or network
manager to interpret the data.
<span class="h3"><a class="selflink" id="section-8.6" href="#section-8.6">8.6</a> X-Window</span>
The X Window System uses the X Window protocol on TCP to draw windows
on a workstation's bitmap display. X Window is much more than a
utility for drawing windows; it is entire philosophy for designing a
user interface.
<span class="h2"><a class="selflink" id="section-9" href="#section-9">9</a>. Other Information</span>
Much information about internet technology was not included in this
tutorial. This section lists information that is considered the next
level of detail for the reader who wishes to learn more.
o administration commands: arp, route, and netstat
o ARP: permanent entry, publish entry, time-out entry, spoofing
o IP route table: host entry, default gateway, subnets
o IP: time-to-live counter, fragmentation, ICMP
o RIP, routing loops
o Domain Name System
<span class="h2"><a class="selflink" id="section-10" href="#section-10">10</a>. References</span>
[<a id="ref-1">1</a>] Comer, D., "Internetworking with TCP/IP Principles, Protocols,
and Architecture", Prentice Hall, Englewood Cliffs, New Jersey,
U.S.A., 1988.
[<a id="ref-2">2</a>] Feinler, E., et al, DDN Protocol Handbook, Volume 2 and 3, DDN
Network Information Center, SRI International, 333 Ravenswood
Avenue, Room EJ291, Menlow Park, California, U.S.A., 1985.
[<a id="ref-3">3</a>] Spider Systems, Ltd., "Packets and Protocols", Spider Systems
Ltd., Stanwell Street, Edinburgh, U.K. EH6 5NG, 1990.
<span class="h2"><a class="selflink" id="section-11" href="#section-11">11</a>. Relation to other RFCs</span>
This RFC is a tutorial and it does not UPDATE or OBSOLETE any other
RFC.
<span class="h2"><a class="selflink" id="section-12" href="#section-12">12</a>. Security Considerations</span>
There are security considerations within the TCP/IP protocol suite.
To some people these considerations are serious problems, to others
they are not; it depends on the user requirements.
<span class="grey">Socolofsky & Kale [Page 27]</span></pre>
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-28" ></span>
<span class="grey"><a href="./rfc1180">RFC 1180</a> A TCP/IP Tutorial January 1991</span>
This tutorial does not discuss these issues, but if you want to learn
more you should start with the topic of ARP-spoofing, then use the
"Security Considerations" section of <a href="./rfc1122">RFC 1122</a> to lead you to more
information.
<span class="h2"><a class="selflink" id="section-13" href="#section-13">13</a>. Authors' Addresses</span>
Theodore John Socolofsky
Spider Systems Limited
Spider Park
Stanwell Street
Edinburgh EH6 5NG
United Kingdom
Phone:
from UK 031-554-9424
from USA 011-44-31-554-9424
Fax:
from UK 031-554-0649
from USA 011-44-31-554-0649
EMail: TEDS@SPIDER.CO.UK
Claudia Jeanne Kale
12 Gosford Place
Edinburgh EH6 4BJ
United Kingdom
Phone:
from UK 031-554-7432
from USA 011-44-31-554-7432
EMail: CLAUDIAK@SPIDER.CO.UK
Socolofsky & Kale [Page 28]
</pre>
|
