1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
|
.. role:: math(raw)
:format: html latex
..
Appendix
========
Default units for Data Exchange entries
---------------------------------------
The default units for Data Exchange entries follow the CXI entries
definition, i.e. are SI based units unless the
“units” attribute is specified. Data Exchange prefers to use the default
SI based units whenever possible.
+-----------------------+-------------------+-----------------------------+
| Quantity | Units | Abbreviation |
+=======================+===================+=============================+
| length | meter | m |
+-----------------------+-------------------+-----------------------------+
| mass | kilogram | kg |
+-----------------------+-------------------+-----------------------------+
| time | second | s |
+-----------------------+-------------------+-----------------------------+
| electric current | ampere | A |
+-----------------------+-------------------+-----------------------------+
| temperature | kelvin | K |
+-----------------------+-------------------+-----------------------------+
| amount of substance | mole | mol |
+-----------------------+-------------------+-----------------------------+
| luminous intensity | candela | cd |
+-----------------------+-------------------+-----------------------------+
| frequency | hertz | Hz |
+-----------------------+-------------------+-----------------------------+
| force | newton | N |
+-----------------------+-------------------+-----------------------------+
| pressure | pascal | Pa |
+-----------------------+-------------------+-----------------------------+
| energy | joule | J |
+-----------------------+-------------------+-----------------------------+
| power | watt | W |
+-----------------------+-------------------+-----------------------------+
| electric potential | volt | V |
+-----------------------+-------------------+-----------------------------+
| capacitance | farad | F |
+-----------------------+-------------------+-----------------------------+
| electric resistance | ohm | Omega |
+-----------------------+-------------------+-----------------------------+
| absorbed dose | gray | Gy |
+-----------------------+-------------------+-----------------------------+
| area | square meter | m^2 |
+-----------------------+-------------------+-----------------------------+
| volume | cubic meter | m^3 |
+-----------------------+-------------------+-----------------------------+
Table: SI (and common derived) base units for different quantities
Exceptions
~~~~~~~~~~
Angles are always defined in degrees *not* in radians and use the
abbreviation “degree”.
Times and Dates
~~~~~~~~~~~~~~~
Times and Dates are always specified according to the `ISO
8601 <http://www.w3.org/TR/NOTE-datetime>`__. This means for example
“1996-07-31T21:15:22+0600”. Note the “T” separating the data from the
time and the “+0600” timezone specification.
Geometry
--------
Coordinate System
~~~~~~~~~~~~~~~~~
The Data Exchange uses the same CXI coordinate system. This is a right
handed system with the z axis parallel to the X-ray beam, with the
positive z direction pointing away from the light source, in the
downstream direction. The y axis is vertical with the positive direction
pointing up, while the x axis is horizontal completing the right handed
system (see Fig. [fig:CoordSystem]). The origin of the coordinate system
is defined by the point where the X-ray beam meets the sample.
.. figure:: figures/dx_CoordSystem.png
:align: center
:alt: The coordinate system used by CXI. The intersection of the X-ray beam with the sample define the origin of the system. The z axis is parallel to the beam and points downstream.
:width: 60.0%
The coordinate system used by CXI. The intersection of the X-ray beam
with the sample define the origin of the system. The z axis is
parallel to the beam and points downstream.
The local coordinate system of objects
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
For many detectors their location and orientation is crucial to
interpret results. Translations and rotations are used to define the
absolute position of each object. But to be able to apply these
transformations we need to know what is the origin of the local
coordinate system of each object. Unless otherwise specified the origin
should be assumed to be the geometrical center of the object in
question. The default orientation of the object should have the longest
axis of the object aligned with the x axis, the second longest with the
y axis and the shortest with the z axis.
|
