/* Copyright (C) 2001-2006 Artifex Software, Inc.
   All Rights Reserved.
  
   This software is provided AS-IS with no warranty, either express or
   implied.

   This software is distributed under license and may not be copied, modified
   or distributed except as expressly authorized under the terms of that
   license.  Refer to licensing information at http://www.artifex.com/
   or contact Artifex Software, Inc.,  7 Mt. Lassen Drive - Suite A-134,
   San Rafael, CA  94903, U.S.A., +1(415)492-9861, for further information.
*/
/* $Id: gdevbj10.c 8250 2007-09-25 13:31:24Z giles $*/
/* Canon Bubble Jet BJ-10e, BJ200, and BJ300 printer driver */
#include "gdevprn.h"

/*
 * The following is taken from the BJ200 Programmer's manual.  The top
 * margin is 3mm (0.12"), and the bottom margin is 6.4mm (0.25").  The
 * left and right margin depend on the type of paper -- US letter or
 * A4 -- but ultimately rest on a print width of 203.2mm (8").  For letter
 * paper, the left margin (and hence the right) is 6.4mm (0.25"), while
 * for A4 paper, both are 3.4mm (0.13").
 *
 * The bottom margin requires a bit of care.  The image is printed
 * as strips, each about 3.4mm wide.  We can only attain the bottom 
 * margin if the final strip coincides with it.  Note that each strip
 * is generated using only 48 of the available 64 jets, and the absence
 * of those bottom 16 jets makes our bottom margin, in effect, about
 * 1.1mm (0.04") larger.
 *
 * The bj200 behaves, in effect, as though the origin were at the first
 * printable position, rather than the top left corner of the page, so
 * we add a translation to the initial matrix to compensate for this.
 *
 * Except for the details of getting the margins correct, the bj200 is
 * no different from the bj10e, and uses the same routine to print each
 * page.
 *
 * NOTE:  The bj200 has a DIP switch called "Text scale mode" and if
 * set, it allows the printer to get 66 lines on a letter-sized page
 * by reducing the line spacing by a factor of 14/15.  If this DIP
 * switch is set, the page image printed by ghostscript will also be
 * similarly squeezed.  Thus text scale mode is something ghostscript
 * would like to disable.
 *
 * According to the bj200 manual, which describes the bj10 commands,
 * the printer can be reset either to the settings determined by the
 * DIP switches, or to the factory defaults, and then some of those
 * settings can be specifically overriden.  Unfortunately, the text
 * scale mode and horizontal print position (for letter vs A4 paper)
 * can not be overriden.  On my bj200, the factory settings are for
 * no text scaling and letter paper, thus using the factory defaults
 * also implies letter paper.  I don't know if this is necessarily
 * true for bj200's sold elsewhere, or for other printers that use
 * the same command set.
 *
 * If your factory defaults are in fact the same, you can compile
 * the driver with USE_FACTORY_DEFAULTS defined, in which case the
 * printer will be reset to the factory defaults for letter paper,
 * and reset to the DIP switch settings for A4 paper.  In this case,
 * with letter-sized paper, the text scale mode will be disabled.
 * Further, by leaving the horizontal print position DIP switch set
 * for A4 paper, gs will be able to print on either A4 or letter
 * paper without changing the DIP switch.  Since it's not clear that
 * the factory defaults are universal, the default behaviour is not
 * to define USE_FACTORY_DEFAULTS, and the printer will always be
 * reset to the DIP switch defaults.
 */

/*
 * According to md@duesti.fido.de (Matthias Duesterhoeft):

It is possible to use the printer Canon BJ-300 (and 330) with Ghostscript if
you use the driver for the Canon BJ-200. The Printer has to be set to
Proprinter Mode. Although it is possible to set the print quality with a DIP
switch, you should add the following to the already existing init-string:
1B 5B 64 01 00 80  (all numbers in hex)
This sets the print quality to letter quality.

The minimum margins are the following:

Portrait:
B5/A4: min. left and right margin: 3.4 mm (0.13")
Letter: min. left and right margin: 6.4 mm (0.25")

Landscape:
B4: min. left and right margin: 9.3 mm (0.37")
A3: min. left and right margin: 37.3 mm (1.47")

The recommended top margin is 12.7 mm (0.5"), although the printer is capable
to start at 0 mm. The recommended bottom margin is 25.4 mm (1"), but 12.7 mm
(0.5") are possible, too. If you ask me, don't use the recommended top and
bottom margins, use 0" and 0.5".

 */

#define BJ200_TOP_MARGIN		0.12
#define BJ200_BOTTOM_MARGIN		0.29
#define BJ200_LETTER_SIDE_MARGIN	0.25
#define BJ200_A4_SIDE_MARGIN		0.13

static dev_proc_open_device(bj200_open);

static dev_proc_print_page(bj10e_print_page);

static gx_device_procs prn_bj200_procs =
  prn_procs(bj200_open, gdev_prn_output_page, gdev_prn_close);

const gx_device_printer far_data gs_bj200_device =
  prn_device(prn_bj200_procs, "bj200",
	DEFAULT_WIDTH_10THS,
	DEFAULT_HEIGHT_10THS,
	360,				/* x_dpi */
	360,				/* y_dpi */
	0, 0, 0, 0,			/* margins filled in by bj200_open */
	1, bj10e_print_page);

/*
 * (<simon@pogner.demon.co.uk>, aka <sjwright@cix.compulink.co.uk>):
 * My bj10ex, which as far as I can tell is just like a bj10e, needs a
 * bottom margin of 0.4" (actually, you must not print within 0.5" of
 * the bottom; somewhere, an extra 0.1" is creeping in).
 *
 * (<jim.hague@acm.org>):
 * I have a BJ10sx and the BJ10sx manual. This states that the top and
 * bottom margins for the BJ10sx are 0.33" and 0.5". The latter may
 * explain Simon's finding. The manual also instructs Win31 users to
 * select 'BJ10e' as their driver, so presumably the margins will be
 * identical and thus also correct for BJ10e. The values for the side
 * margins given are identical to those above.
 *
 * As of 2nd Nov 2001 the BJ10 sx manual is at
 * http://www.precision.com/Printer%20Manuals/Canon%20BJ-10sx%20Manual.pdf.
 */

#define BJ10E_TOP_MARGIN		0.33
#define BJ10E_BOTTOM_MARGIN		(0.50 + 0.04)

static dev_proc_open_device(bj10e_open);

static gx_device_procs prn_bj10e_procs =
  prn_procs(bj10e_open, gdev_prn_output_page, gdev_prn_close);

const gx_device_printer far_data gs_bj10e_device =
  prn_device(prn_bj10e_procs, "bj10e",
	DEFAULT_WIDTH_10THS,
	DEFAULT_HEIGHT_10THS,
	360,				/* x_dpi */
	360,				/* y_dpi */
	0,0,0,0,			/* margins */
	1, bj10e_print_page);

/*
 * Notes on the BJ10e/BJ200 command set.
 *

According to the BJ200 manual, the "set initial condition" sequence (ESC [
K) has 2 bytes which can override the DIP switches -- these are the last 2
bytes.  Several bits are listed as "reserved" -- one or more may possibly
affect the sheet feeder.  The first is referred to as <P1>, with the
following meaning:
				1		0
bit 7	ignore/process P1	ignore		process
bit 6	reserved
bit 5	alarm			disabled	enabled
bit 4	automatic CR		CR+LF		CR
bit 3	automatic LF		CR+LF		LF
bit 2	page length		12 inches	11 inches
bit 1	style for zero		slashed		not slashed
bit 0	character set		set 2		set 1

The last byte is <P2>, with the following meaning:
				1		0
bit 7	ignore/process P2	ignore		process
bit 6	code page		850		437
bit 5	reserved
bit 4	reserved
bit 3	reserved
bit 2	reserved
bit 1	reserved
bit 0	reserved

The automatic CR setting is important to gs, but the rest shouldn't matter
(gs doesn't print characters or send LF, and it explicitly sets the page
length).  The sequence ESC 5 <n> controls automatic CR -- if <n> is 0x00,
it is turned off (CR only) and if <n> is 0x01, it is turned on (CR + LF).
So we do following: Change the initialization string to so that the last 2
of the 9 bytes are \200 rather than \000.  Then add
	|* Turn off automatic carriage return, otherwise we get line feeds. *|
	fwrite("\0335\000", 1, 3, prn_stream);
after the initialization.  (Actually, instead of setting the last 2 bytes
to \200, we suppress them altogether by changing the byte count from \004
to \002 (the byte count is the 4th (low 8 bits) and 5th (high 8 bits) bytes
in the initialization sequence).)

*/

/* ------ Internal routines ------ */

/* Open the printer, and set the margins. */
static int
bj200_open(gx_device *pdev)
{
	/* Change the margins according to the paper size.
	   The top and bottom margins don't seem to depend on the
	   page length, but on the paper handling mechanism;
	   The side margins do depend on the paper width, as the
	   printer centres the 8" print line on the page. */

	static const float a4_margins[4] =
	 {	(float)BJ200_A4_SIDE_MARGIN, (float)BJ200_BOTTOM_MARGIN,
		(float)BJ200_A4_SIDE_MARGIN, (float)BJ200_TOP_MARGIN
	 };
	static const float letter_margins[4] =
	 {	(float)BJ200_LETTER_SIDE_MARGIN, (float)BJ200_BOTTOM_MARGIN,
		(float)BJ200_LETTER_SIDE_MARGIN, (float)BJ200_TOP_MARGIN
	 };

	gx_device_set_margins(pdev,
		(pdev->width / pdev->x_pixels_per_inch <= 8.4 ?
		 a4_margins : letter_margins),
		true);
	return gdev_prn_open(pdev);
}

static int
bj10e_open(gx_device *pdev)
{
        /* See bj200_open() */
	static const float a4_margins[4] =
	 {	(float)BJ200_A4_SIDE_MARGIN, (float)BJ10E_BOTTOM_MARGIN,
		(float)BJ200_A4_SIDE_MARGIN, (float)BJ10E_TOP_MARGIN
	 };
	static const float letter_margins[4] =
	 {	(float)BJ200_LETTER_SIDE_MARGIN, (float)BJ10E_BOTTOM_MARGIN,
		(float)BJ200_LETTER_SIDE_MARGIN, (float)BJ10E_TOP_MARGIN
	 };

	gx_device_set_margins(pdev,
		(pdev->width / pdev->x_pixels_per_inch <= 8.4 ?
		 a4_margins : letter_margins),
		true);
	return gdev_prn_open(pdev);
}

/* Send the page to the printer. */
static int
bj10e_print_page(gx_device_printer *pdev, FILE *prn_stream)
{	int line_size = gx_device_raster((gx_device *)pdev, 0);
	int xres = (int)pdev->x_pixels_per_inch;
	int yres = (int)pdev->y_pixels_per_inch;
	int mode = (yres == 180 ?
			(xres == 180 ? 11 : 12) :
			(xres == 180 ? 14 : 16));
	int bytes_per_column = (yres == 180) ? 3 : 6;
	int bits_per_column = bytes_per_column * 8;
	int skip_unit = bytes_per_column * 3;
	byte *in = (byte *)gs_malloc(pdev->memory, 8, line_size, "bj10e_print_page(in)");
	byte *out = (byte *)gs_malloc(pdev->memory, bits_per_column, line_size, "bj10e_print_page(out)");
	int lnum = 0;
	int skip = 0;
	int code = 0;
	int last_row = dev_print_scan_lines(pdev);
	int limit = last_row - bits_per_column;

	if ( in == 0 || out == 0 )
	{	code = gs_note_error(gs_error_VMerror);
		goto fin;
	}

	/* Initialize the printer. */
#ifdef USE_FACTORY_DEFAULTS
	/* Check for U.S. letter vs. A4 paper. */
	fwrite(( pdev->width / pdev->x_pixels_per_inch <= 8.4 ?
		"\033[K\002\000\000\044"	/*A4--DIP switch defaults*/ :
		"\033[K\002\000\004\044"	/*letter--factory defaults*/ ),
	       1, 7, prn_stream);
#else
	fwrite("\033[K\002\000\000\044", 1, 7, prn_stream);
#endif

	/* Turn off automatic carriage return, otherwise we get line feeds. */
	fwrite("\0335\000", 1, 3, prn_stream);

	/* Set vertical spacing. */
	fwrite("\033[\\\004\000\000\000", 1, 7, prn_stream);
	fputc(yres & 0xff, prn_stream);
	fputc(yres >> 8, prn_stream);

	/* Set the page length.  This is the printable length, in inches. */
	fwrite("\033C\000", 1, 3, prn_stream);
	fputc((last_row + yres - 1)/yres, prn_stream);

	/* Transfer pixels to printer.  The last row we can print is defined
	   by "last_row".  Only the bottom of the print head can print at the
	   bottom margin, and so we align the final printing pass.  The print
	   head is kept from moving below "limit", which is exactly one pass
	   above the bottom margin.  Once it reaches this limit, we make our
	   final printing pass of a full "bits_per_column" rows. */
	while ( lnum < last_row )
	   {	
		byte *in_data;
		byte *in_end = in + line_size;
		byte *out_beg = out;
		byte *out_end = out + bytes_per_column * pdev->width;
		byte *outl = out;
		int bnum;

		/* Copy 1 scan line and test for all zero. */
		code = gdev_prn_get_bits(pdev, lnum, in, &in_data);
		if ( code < 0 ) goto xit;
		/* The mem... or str... functions should be faster than */
		/* the following code, but all systems seem to implement */
		/* them so badly that this code is faster. */
		   {	register const long *zip = (const long *)in_data;
			register int zcnt = line_size;
			register const byte *zipb;
			for ( ; zcnt >= 4 * sizeof(long); zip += 4, zcnt -= 4 * sizeof(long) )
			   {	if ( zip[0] | zip[1] | zip[2] | zip[3] )
					goto notz;
			   }
			zipb = (const byte *)zip;
			while ( --zcnt >= 0 )
			   {
				if ( *zipb++ )
					goto notz;
			   }
			/* Line is all zero, skip */
			lnum++;
			skip++;
			continue;
notz:			;
		   }

		/* Vertical tab to the appropriate position.  Note here that
		   we make sure we don't move below limit. */
		if ( lnum > limit )
		    {	skip -= (lnum - limit);
			lnum = limit;
		    }
		while ( skip > 255 )
		   {	fputs("\033J\377", prn_stream);
			skip -= 255;
		   }
		if ( skip )
			fprintf(prn_stream, "\033J%c", skip);

		/* If we've printed as far as "limit", then reset "limit"
		   to "last_row" for the final printing pass. */
		if ( lnum == limit )
			limit = last_row;
		skip = 0;

		/* Transpose in blocks of 8 scan lines. */
		for ( bnum = 0; bnum < bits_per_column; bnum += 8 )
		   {	int lcnt = min(8, limit - lnum);
			byte *inp = in;
			byte *outp = outl;
		   	lcnt = gdev_prn_copy_scan_lines(pdev,
				lnum, in, lcnt * line_size);
			if ( lcnt < 0 )
			   {	code = lcnt;
				goto xit;
			   }
			if ( lcnt < 8 )
				memset(in + lcnt * line_size, 0,
				       (8 - lcnt) * line_size);
			for ( ; inp < in_end; inp++, outp += bits_per_column )
			   {	gdev_prn_transpose_8x8(inp, line_size,
					outp, bytes_per_column);
			   }
			outl++;
			lnum += lcnt;
			skip += lcnt;
		   }

		/* Send the bits to the printer.  We alternate horizontal
		   skips with the data.  The horizontal skips are in units
		   of 1/120 inches, so we look at the data in groups of
		   3 columns, since 3/360 = 1/120, and 3/180 = 2/120.  */
		outl = out;
		do
		   {	int count;
			int n;
			byte *out_ptr;

			/* First look for blank groups of columns. */
			while(outl < out_end)
			   {	n = count = min(out_end - outl, skip_unit);
				out_ptr = outl;
				while ( --count >= 0 )
				   {	if ( *out_ptr++ )
						break;
				   }
				if ( count >= 0 )
					break;
				else
					outl = out_ptr;
			   }
			if (outl >= out_end)
				break;
			if (outl > out_beg)
			   {	count = (outl - out_beg) / skip_unit;
				if ( xres == 180 ) count <<= 1;
				fprintf(prn_stream, "\033d%c%c",
					count & 0xff, count >> 8);
			   }

			/* Next look for non-blank groups of columns. */
			out_beg = outl;
			outl += n;
			while(outl < out_end)
			   {	n = count = min(out_end - outl, skip_unit);
				out_ptr = outl;
				while ( --count >= 0 )
				   {	if ( *out_ptr++ )
						break;
				   }
				if ( count < 0 )
					break;
				else
					outl += n;
			   }
			count = outl - out_beg + 1;
			fprintf(prn_stream, "\033[g%c%c%c",
				count & 0xff, count >> 8, mode);
			fwrite(out_beg, 1, count - 1, prn_stream);
			out_beg = outl;
			outl += n;
		   }
		while ( out_beg < out_end );

		fputc('\r', prn_stream);
	   }

	/* Eject the page */
xit:	fputc(014, prn_stream);	/* form feed */
	fflush(prn_stream);
fin:	if ( out != 0 )
		gs_free(pdev->memory, (char *)out, bits_per_column, line_size,
			"bj10e_print_page(out)");
	if ( in != 0 )
		gs_free(pdev->memory, (char *)in, 8, line_size, "bj10e_print_page(in)");
	return code;
}