1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
|
# $Id: att-dpexpress-2,v 1.2 2001/06/04 05:09:46 darren Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Configuration for using the Class 2 command interface with
# an AT&T DataPort Express 14.4 modem. Model 3715-A1-202
# Firmware version (ati1) FW Level 091394 Checksum 182050 V1.15.07 SA
# or newer.
#
# Hardware flow control is used by default.
#
# CONFIG: CLASS2: AT?T*PARADYNE*-ROCKWELL*144DPI*
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use class 2 interface
ModemRate: 38400 # set rate for DCE-DTE communication
ModemFlowControl: rtscts # default
#
ModemHardFlowCmd: AT&R0\D1\Q3 # use RTS/CTS and enable RS232 handling
ModemSoftFlowCmd: AT&R1\D0\Q1 # use RTS/CTS and enable RS232 handling
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
ModemSetupAACmd: AT+FAA=1 # enable adaptive-answer in Class 2
#
ModemRecvFillOrder: MSB2LSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
ModemDialCmd: ATDT%s # T for tone dialing
#
# Chip locks the line rate and switches to xon/xoff flow
# control when receiving facsimile--we must follow suit.
#
ModemAnswerFaxBeginCmd: "<19200><xon>" # lock line rate & switch flow control
#
Class2RecvDataTrigger: "\022" # character sent to modem to start recv
#
# These are known to not be implemented with the above
# firmware rev. Sending them to the modem does not harm anything,
# but generates an ERROR result that can generate questions from the
# naive--so we disable them here.
#
Class2CQQueryCmd: AT # +FAQ=? query for copy quality capabilities
Class2APQueryCmd: none # +FAP=? not supported on this modem
Class2SPLCmd: none # +FSPL= Request to Poll
Class2TBCCmd: none # +FTBC= Phase C Trasmit Data Block Size
Class2PHCTOCmd: none # +FPHCTO= phase C timeout parameter
Class2BugCmd: none # +FBUG= HDLC frame tracing
|
