1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
|
# $Id$
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#
#
# Configuration for a Motorola RC288DPi-based Class 1 modem.
# Lifestyle 28.8 S209415900 -01 1/16/95 3:30 PM
#
# CONFIG:CLASS1:288:Motorola:.*: Manufacturer=Motorola Model=28.8
# CONFIG:CLASS1:960:Motorola.*:.*: Manufacturer=Motorola Model=SM56
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use class 1 interface
ModemRate: 19200 # locked for fax sending&receiving
ModemFlowControl: rtscts # default
#
#ModemNoFlowCmd: AT\Q # disable flow control cmd
#ModemSoftFlowCmd: AT&R1\Q1 # software flow control cmd
#ModemHardFlowCmd: AT&R\Q3 # hardware flow control cmd
ModemSetupDTRCmd: AT&D3 # DTR off causes modem to reset
ModemSetupDCDCmd: AT&C1 # DCD follows carrier
#ModemSetupAACmd: AT+FAA=1
#
#ModemAnswerCmd: "AT*FR\nATA" # enable autobaud before answering
#ModemWaitForConnect: yes # modem sends FAX/DATA first
#
# Apparently Rev 2 of the firmware requires that you send ATO
# to initiate a data connection when adaptive answer is set; the
# following will send ATO and then wait for the CONNECT response.
#
#ModemAnswerDataBeginCmd:"ATO\n<waitfor\072CONNECT>"
#
#ModemMfrQueryCmd: !Motorola
#ModemModelQueryCmd: !28.8
#ModemRevQueryCmd: AT%V # model and firmware rev
#
# Caller ID configuration setup; add AT*ID1 to ModemResetCmds
# to enable functionality (when supported by the local Telco).
#
#CallIDPattern: "CALLER NUMBER: " # pattern string for phone number info
#CallIDPattern: "CALLER NAME: " # pattern string for identity info
#
|
