1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
|
/*
* BK Id: SCCS/s.keylargo.h 1.13 08/19/01 22:23:04 paulus
*/
/*
* keylargo.h: definitions for using the "KeyLargo" I/O controller chip.
*
*/
/* "Pangea" chipset has keylargo device-id 0x25 while core99
* has device-id 0x22. The rev. of the pangea one is 0, so we
* fake an artificial rev. in keylargo_rev by oring 0x100
*/
#define KL_PANGEA_REV 0x100
/* offset from base for feature control registers */
#define KEYLARGO_MBCR 0x34 /* Media bay control/status */
#define KEYLARGO_FCR0 0x38
#define KEYLARGO_FCR1 0x3c
#define KEYLARGO_FCR2 0x40
#define KEYLARGO_FCR3 0x44
#define KEYLARGO_FCR4 0x48
/* GPIO registers */
#define KEYLARGO_GPIO_LEVELS0 0x50
#define KEYLARGO_GPIO_LEVELS1 0x54
#define KEYLARGO_GPIO_EXTINT_0 0x58
#define KEYLARGO_GPIO_EXTINT_CNT 18
#define KEYLARGO_GPIO_0 0x6A
#define KEYLARGO_GPIO_CNT 17
#define KEYLARGO_GPIO_OUTPUT_ENABLE 0x04
#define KEYLARGO_GPIO_OUTOUT_DATA 0x01
/* Specific GPIO regs */
#define KL_GPIO_MODEM_RESET (KEYLARGO_GPIO_0+0x03) /* Pangea */
#define KL_GPIO_MODEM_POWER (KEYLARGO_GPIO_0+0x02) /* Pangea */
/* Hrm... this one is only to be used on Pismo. It seeem to also
* control the timebase enable on other machines. Still to be
* experimented... --BenH.
*/
#define KL_GPIO_FW_CABLE_POWER (KEYLARGO_GPIO_0+0x09)
#define KL_GPIO_TB_ENABLE (KEYLARGO_GPIO_0+0x09)
#define KL_GPIO_ETH_PHY_RESET (KEYLARGO_GPIO_0+0x10)
#define KL_GPIO_EXTINT_CPU1 (KEYLARGO_GPIO_0+0x0a)
#define KL_GPIO_EXTINT_CPU1_ASSERT 0x04
#define KL_GPIO_EXTINT_CPU1_RELEASE 0x38
#define KL_GPIO_RESET_CPU0 (KEYLARGO_GPIO_EXTINT_0+0x03)
#define KL_GPIO_RESET_CPU1 (KEYLARGO_GPIO_EXTINT_0+0x04)
#define KL_GPIO_RESET_CPU2 (KEYLARGO_GPIO_EXTINT_0+0x0f)
#define KL_GPIO_RESET_CPU3 (KEYLARGO_GPIO_EXTINT_0+0x10)
#define KL_GPIO_PMU_MESSAGE_IRQ (KEYLARGO_GPIO_EXTINT_0+0x09)
#define KL_GPIO_PMU_MESSAGE_BIT 0x02
#define KL_GPIO_AIRPORT_0 (KEYLARGO_GPIO_EXTINT_0+0x0a)
#define KL_GPIO_AIRPORT_1 (KEYLARGO_GPIO_EXTINT_0+0x0d)
#define KL_GPIO_AIRPORT_2 (KEYLARGO_GPIO_0+0x0d)
#define KL_GPIO_AIRPORT_3 (KEYLARGO_GPIO_0+0x0e)
#define KL_GPIO_AIRPORT_4 (KEYLARGO_GPIO_0+0x0f)
/*
* Bits in feature control register
*/
#define KL_MBCR_MB0_DEV_ENABLE 0x00001000
#define KL_MBCR_MB0_DEV_POWER 0x00000400
#define KL_MBCR_MB0_DEV_RESET 0x00000200
#define KL_MBCR_MB0_ENABLE 0x00000100
#define KL_MBCR_MB1_DEV_ENABLE 0x10000000
#define KL_MBCR_MB1_DEV_POWER 0x04000000
#define KL_MBCR_MB1_DEV_RESET 0x02000000
#define KL_MBCR_MB1_ENABLE 0x01000000
#define KL0_SCC_B_INTF_ENABLE 0x00000001 /* ??? */
#define KL0_SCC_A_INTF_ENABLE 0x00000002 /* ??? */
#define KL0_SCC_SLOWPCLK 0x00000004
#define KL0_SCC_RESET 0x00000008
#define KL0_SCCA_ENABLE 0x00000010
#define KL0_SCCB_ENABLE 0x00000020
#define KL0_SCC_CELL_ENABLE 0x00000040
#define KL0_USB0_PAD_SUSPEND0 0x00040000
#define KL0_USB0_PAD_SUSPEND1 0x00080000
#define KL0_USB0_CELL_ENABLE 0x00100000
#define KL0_USB1_PAD_SUSPEND0 0x00400000
#define KL0_USB1_PAD_SUSPEND1 0x00800000
#define KL0_USB1_CELL_ENABLE 0x01000000
/* KL id 0x22 only */
#define KL0_USB_REF_SUSPEND 0x10000000
#define KL0_IRDA_ENABLE 0x00008000
#define KL0_IRDA_CLK32_ENABLE 0x00010000
#define KL0_IRDA_CLK19_ENABLE 0x00020000
/* KL id 0x25 (pangea) only */
#define KL0_USB1_PAD_SUSPEND_SEL 0x00020000
#define KL0_USB1_REF_SUSPEND 0x00010000
#define KL0_USB1_REF_SUSPEND_SEL 0x00008000
#define KL0_USB1_PMI 0x00004000
#define KL0_USB0_PAD_SUSPEND_SEL 0x00002000
#define KL0_USB0_REF_SUSPEND 0x00001000
#define KL0_USB0_REF_SUSPEND_SEL 0x00000800
#define KL0_USB0_PMI 0x00000400
#define KL0_SERIAL_ENABLE (KL0_SCC_B_INTF_ENABLE | \
KL0_SCC_SLOWPCLK | \
KL0_SCC_CELL_ENABLE | KL0_SCCA_ENABLE)
#define KL1_AUDIO_SEL_22MCLK 0x00000002
#define KL1_AUDIO_CLK_ENABLE_BIT 0x00000008
#define KL1_AUDIO_CLK_OUT_ENABLE 0x00000020 /* Burgundy only ? */
#define KL1_AUDIO_CELL_ENABLE 0x00000040
#define KL1_AUDIO_CHOOSE 0x00000080 /* Burgundy only ? */
#define KL1_I2S0_CELL_ENABLE 0x00000400
#define KL1_I2S0_CLK_ENABLE_BIT 0x00001000
#define KL1_I2S0_ENABLE 0x00002000
#define KL1_I2S1_CELL_ENABLE 0x00020000
#define KL1_I2S1_CLK_ENABLE_BIT 0x00080000
#define KL1_I2S1_ENABLE 0x00100000
#define KL1_EIDE0_ENABLE 0x00800000
#define KL1_EIDE0_RESET_N 0x01000000
#define KL1_EIDE1_ENABLE 0x04000000
#define KL1_EIDE1_RESET_N 0x08000000
#define KL1_UIDE_ENABLE 0x20000000
#define KL1_UIDE_RESET_N 0x40000000
#define KL2_IOBUS_ENABLE 0x00000002
#define KL2_SLEEP_STATE_BIT 0x00000100
#define KL2_MPIC_ENABLE 0x00020000
#define KL2_MODEM_POWER_N 0x02000000
#define KL2_AIRPORT_RESET_N 0x08000000 /* Or power ? */
#define KL3_SHUTDOWN_PLL_TOTAL 0x00000001
#define KL3_SHUTDOWN_PLLKW6 0x00000002
#define KL3_SHUTDOWN_PLLKW4 0x00000004
#define KL3_SHUTDOWN_PLLKW35 0x00000008
#define KL3_SHUTDOWN_PLLKW12 0x00000010
#define KL3_PLL_RESET 0x00000020
#define KL3_SHUTDOWN_PLL2X 0x00000080
#define KL3_CLK66_ENABLE 0x00000100
#define KL3_CLK49_ENABLE 0x00000200
#define KL3_CLK45_ENABLE 0x00000400
#define KL3_CLK31_ENABLE 0x00000800
#define KL3_TIMER_CLK18_ENABLE 0x00001000
#define KL3_I2S1_CLK18_ENABLE 0x00002000
#define KL3_I2S0_CLK18_ENABLE 0x00004000
#define KL3_VIA_CLK16_ENABLE 0x00008000
#define KL3_STOPPING33_ENABLED 0x00080000
/* Port 0,1 : bus 0, port 2,3 : bus 1 */
#define KL4_SET_PORT_ENABLE(p) (0x00000008 << ((p)<<3))
#define KL4_SET_PORT_RESUME(p) (0x00000004 << ((p)<<3))
#define KL4_SET_PORT_CONNECT(p) (0x00000002 << ((p)<<3))
#define KL4_SET_PORT_DISCONNECT(p) (0x00000001 << ((p)<<3))
#define KL4_GET_PORT_RESUME(p) (0x00000040 << ((p)<<3))
#define KL4_GET_PORT_CONNECT(p) (0x00000020 << ((p)<<3))
#define KL4_GET_PORT_DISCONNECT(p) (0x00000010 << ((p)<<3))
|
