1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
|
/*
* Device Tree file for OpenBlocks AX3-4 board
*
* Copyright (C) 2012 Marvell
*
* Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "armada-xp-mv78260.dtsi"
/ {
model = "PlatHome OpenBlocks AX3-4 board";
compatible = "plathome,openblocks-ax3-4", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp";
chosen {
bootargs = "console=ttyS0,115200 earlyprintk";
};
memory {
device_type = "memory";
reg = <0 0x00000000 0 0x40000000>; /* 1 GB soldered on */
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x8000000>;
devbus-bootcs {
status = "okay";
/* Device Bus parameters are required */
/* Read parameters */
devbus,bus-width = <16>;
devbus,turn-off-ps = <60000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <124000>;
devbus,acc-next-ps = <248000>;
devbus,rd-setup-ps = <0>;
devbus,rd-hold-ps = <0>;
/* Write parameters */
devbus,sync-enable = <0>;
devbus,wr-high-ps = <60000>;
devbus,wr-low-ps = <60000>;
devbus,ale-wr-ps = <60000>;
/* NOR 128 MiB */
nor@0 {
compatible = "cfi-flash";
reg = <0 0x8000000>;
bank-width = <2>;
};
};
pcie-controller {
status = "okay";
/* Internal mini-PCIe connector */
pcie@1,0 {
/* Port 0, Lane 0 */
status = "okay";
};
};
internal-regs {
serial@12000 {
status = "okay";
};
serial@12100 {
status = "okay";
};
pinctrl {
led_pins: led-pins-0 {
marvell,pins = "mpp49", "mpp51", "mpp53";
marvell,function = "gpio";
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins>;
red_led {
label = "red_led";
gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
default-state = "off";
};
yellow_led {
label = "yellow_led";
gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
default-state = "off";
};
green_led {
label = "green_led";
gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
button@1 {
label = "Init Button";
linux,code = <KEY_POWER>;
gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
};
};
mdio {
phy0: ethernet-phy@0 {
reg = <0>;
};
phy1: ethernet-phy@1 {
reg = <1>;
};
phy2: ethernet-phy@2 {
reg = <2>;
};
phy3: ethernet-phy@3 {
reg = <3>;
};
};
ethernet@70000 {
status = "okay";
phy = <&phy0>;
phy-mode = "sgmii";
};
ethernet@74000 {
status = "okay";
phy = <&phy1>;
phy-mode = "sgmii";
};
ethernet@30000 {
status = "okay";
phy = <&phy2>;
phy-mode = "sgmii";
};
ethernet@34000 {
status = "okay";
phy = <&phy3>;
phy-mode = "sgmii";
};
i2c@11000 {
status = "okay";
clock-frequency = <400000>;
};
i2c@11100 {
status = "okay";
clock-frequency = <400000>;
s35390a: s35390a@30 {
compatible = "s35390a";
reg = <0x30>;
};
};
sata@a0000 {
nr-ports = <2>;
status = "okay";
};
/* Front side USB 0 */
usb@50000 {
status = "okay";
};
/* Front side USB 1 */
usb@51000 {
status = "okay";
};
};
};
};
|
