1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
|
Qualcomm adreno/snapdragon GPU
Required properties:
- compatible: "qcom,adreno-XYZ.W", "qcom,adreno" or
"amd,imageon-XYZ.W", "amd,imageon"
for example: "qcom,adreno-306.0", "qcom,adreno"
Note that you need to list the less specific "qcom,adreno" (since this
is what the device is matched on), in addition to the more specific
with the chip-id.
If "amd,imageon" is used, there should be no top level msm device.
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt signal from the gpu.
- clocks: device clocks (if applicable)
See ../clocks/clock-bindings.txt for details.
- clock-names: the following clocks are required by a3xx, a4xx and a5xx
cores:
* "core"
* "iface"
* "mem_iface"
For GMU attached devices the GPU clocks are not used and are not required. The
following devices should not list clocks:
- qcom,adreno-630.2
- iommus: optional phandle to an adreno iommu instance
- operating-points-v2: optional phandle to the OPP operating points
- interconnects: optional phandle to an interconnect provider. See
../interconnect/interconnect.txt for details. Some A3xx and all A4xx platforms
will have two paths; all others will have one path.
- interconnect-names: The names of the interconnect paths that correspond to the
interconnects property. Values must be gfx-mem and ocmem.
- qcom,gmu: For GMU attached devices a phandle to the GMU device that will
control the power for the GPU. Applicable targets:
- qcom,adreno-630.2
- zap-shader: For a5xx and a6xx devices this node contains a memory-region that
points to reserved memory to store the zap shader that can be used to help
bring the GPU out of secure mode.
- firmware-name: optional property of the 'zap-shader' node, listing the
relative path of the device specific zap firmware.
- sram: phandle to the On Chip Memory (OCMEM) that's present on some a3xx and
a4xx Snapdragon SoCs. See
Documentation/devicetree/bindings/sram/qcom,ocmem.yaml.
Example 3xx/4xx:
/ {
...
gpu: adreno@fdb00000 {
compatible = "qcom,adreno-330.2",
"qcom,adreno";
reg = <0xfdb00000 0x10000>;
reg-names = "kgsl_3d0_reg_memory";
interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "kgsl_3d0_irq";
clock-names = "core",
"iface",
"mem_iface";
clocks = <&mmcc OXILI_GFX3D_CLK>,
<&mmcc OXILICX_AHB_CLK>,
<&mmcc OXILICX_AXI_CLK>;
sram = <&gpu_sram>;
power-domains = <&mmcc OXILICX_GDSC>;
operating-points-v2 = <&gpu_opp_table>;
iommus = <&gpu_iommu 0>;
};
gpu_sram: ocmem@fdd00000 {
compatible = "qcom,msm8974-ocmem";
reg = <0xfdd00000 0x2000>,
<0xfec00000 0x180000>;
reg-names = "ctrl",
"mem";
clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>,
<&mmcc OCMEMCX_OCMEMNOC_CLK>;
clock-names = "core",
"iface";
#address-cells = <1>;
#size-cells = <1>;
gpu_sram: gpu-sram@0 {
reg = <0x0 0x100000>;
ranges = <0 0 0xfec00000 0x100000>;
};
};
};
Example a6xx (with GMU):
/ {
...
gpu@5000000 {
compatible = "qcom,adreno-630.2", "qcom,adreno";
#stream-id-cells = <16>;
reg = <0x5000000 0x40000>, <0x509e000 0x10>;
reg-names = "kgsl_3d0_reg_memory", "cx_mem";
/*
* Look ma, no clocks! The GPU clocks and power are
* controlled entirely by the GMU
*/
interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
iommus = <&adreno_smmu 0>;
operating-points-v2 = <&gpu_opp_table>;
interconnects = <&rsc_hlos MASTER_GFX3D &rsc_hlos SLAVE_EBI1>;
interconnect-names = "gfx-mem";
gpu_opp_table: opp-table {
compatible = "operating-points-v2";
opp-430000000 {
opp-hz = /bits/ 64 <430000000>;
opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
opp-peak-kBps = <5412000>;
};
opp-355000000 {
opp-hz = /bits/ 64 <355000000>;
opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
opp-peak-kBps = <3072000>;
};
opp-267000000 {
opp-hz = /bits/ 64 <267000000>;
opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
opp-peak-kBps = <3072000>;
};
opp-180000000 {
opp-hz = /bits/ 64 <180000000>;
opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
opp-peak-kBps = <1804000>;
};
};
qcom,gmu = <&gmu>;
zap-shader {
memory-region = <&zap_shader_region>;
firmware-name = "qcom/LENOVO/81JL/qcdxkmsuc850.mbn"
};
};
};
|
