1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
Freescale i.MX DRM master device
================================
The freescale i.MX DRM master device is a virtual device needed to list all
IPU or other display interface nodes that comprise the graphics subsystem.
Required properties:
- compatible: Should be "fsl,imx-display-subsystem"
- ports: Should contain a list of phandles pointing to display interface ports
of IPU devices
example:
display-subsystem {
compatible = "fsl,imx-display-subsystem";
ports = <&ipu_di0>;
};
Freescale i.MX IPUv3
====================
Required properties:
- compatible: Should be "fsl,<chip>-ipu" where <chip> is one of
- imx51
- imx53
- imx6q
- imx6qp
- reg: should be register base and length as documented in the
datasheet
- interrupts: Should contain sync interrupt and error interrupt,
in this order.
- resets: phandle pointing to the system reset controller and
reset line index, see reset/fsl,imx-src.txt for details
Additional required properties for fsl,imx6qp-ipu:
- fsl,prg: phandle to prg node associated with this IPU instance
Optional properties:
- port@[0-3]: Port nodes with endpoint definitions as defined in
Documentation/devicetree/bindings/media/video-interfaces.txt.
Ports 0 and 1 should correspond to CSI0 and CSI1,
ports 2 and 3 should correspond to DI0 and DI1, respectively.
example:
ipu: ipu@18000000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx53-ipu";
reg = <0x18000000 0x080000000>;
interrupts = <11 10>;
resets = <&src 2>;
ipu_di0: port@2 {
reg = <2>;
ipu_di0_disp0: endpoint {
remote-endpoint = <&display_in>;
};
};
};
Freescale i.MX PRE (Prefetch Resolve Engine)
============================================
Required properties:
- compatible: should be "fsl,imx6qp-pre"
- reg: should be register base and length as documented in the
datasheet
- clocks : phandle to the PRE axi clock input, as described
in Documentation/devicetree/bindings/clock/clock-bindings.txt and
Documentation/devicetree/bindings/clock/imx6q-clock.yaml.
- clock-names: should be "axi"
- interrupts: should contain the PRE interrupt
- fsl,iram: phandle pointing to the mmio-sram device node, that should be
used for the PRE SRAM double buffer.
example:
pre@21c8000 {
compatible = "fsl,imx6qp-pre";
reg = <0x021c8000 0x1000>;
interrupts = <GIC_SPI 90 IRQ_TYPE_EDGE_RISING>;
clocks = <&clks IMX6QDL_CLK_PRE0>;
clock-names = "axi";
fsl,iram = <&ocram2>;
};
Freescale i.MX PRG (Prefetch Resolve Gasket)
============================================
Required properties:
- compatible: should be "fsl,imx6qp-prg"
- reg: should be register base and length as documented in the
datasheet
- clocks : phandles to the PRG ipg and axi clock inputs, as described
in Documentation/devicetree/bindings/clock/clock-bindings.txt and
Documentation/devicetree/bindings/clock/imx6q-clock.yaml.
- clock-names: should be "ipg" and "axi"
- fsl,pres: phandles to the PRE units attached to this PRG, with the fixed
PRE as the first entry and the muxable PREs following.
example:
prg@21cc000 {
compatible = "fsl,imx6qp-prg";
reg = <0x021cc000 0x1000>;
clocks = <&clks IMX6QDL_CLK_PRG0_APB>,
<&clks IMX6QDL_CLK_PRG0_AXI>;
clock-names = "ipg", "axi";
fsl,pres = <&pre1>, <&pre2>, <&pre3>;
};
Parallel display support
========================
Required properties:
- compatible: Should be "fsl,imx-parallel-display"
Optional properties:
- interface-pix-fmt: How this display is connected to the
display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
and "lvds666".
- edid: verbatim EDID data block describing attached display.
- ddc: phandle describing the i2c bus handling the display data
channel
- port@[0-1]: Port nodes with endpoint definitions as defined in
Documentation/devicetree/bindings/media/video-interfaces.txt.
Port 0 is the input port connected to the IPU display interface,
port 1 is the output port connected to a panel.
example:
disp0 {
compatible = "fsl,imx-parallel-display";
edid = [edid-data];
interface-pix-fmt = "rgb24";
port@0 {
reg = <0>;
display_in: endpoint {
remote-endpoint = <&ipu_di0_disp0>;
};
};
port@1 {
reg = <1>;
display_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
panel {
...
port {
panel_in: endpoint {
remote-endpoint = <&display_out>;
};
};
};
|
