1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
|
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* Table of the Omap register configurations for the FUNC_MUX and
* PULL_DWN combinations.
*
* Copyright (C) 2004 - 2008 Texas Instruments Inc.
* Copyright (C) 2003 - 2008 Nokia Corporation
*
* Written by Tony Lindgren
*
* NOTE: Please use the following naming style for new pin entries.
* For example, W8_1610_MMC2_DAT0, where:
* - W8 = ball
* - 1610 = 1510 or 1610, none if common for both 1510 and 1610
* - MMC2_DAT0 = function
*/
#ifndef __ASM_ARCH_MUX_H
#define __ASM_ARCH_MUX_H
#include <linux/soc/ti/omap1-mux.h>
#define PU_PD_SEL_NA 0 /* No pu_pd reg available */
#define PULL_DWN_CTRL_NA 0 /* No pull-down control needed */
#ifdef CONFIG_OMAP_MUX_DEBUG
#define MUX_REG(reg, mode_offset, mode) .mux_reg_name = "FUNC_MUX_CTRL_"#reg, \
.mux_reg = FUNC_MUX_CTRL_##reg, \
.mask_offset = mode_offset, \
.mask = mode,
#define PULL_REG(reg, bit, status) .pull_name = "PULL_DWN_CTRL_"#reg, \
.pull_reg = PULL_DWN_CTRL_##reg, \
.pull_bit = bit, \
.pull_val = status,
#define PU_PD_REG(reg, status) .pu_pd_name = "PU_PD_SEL_"#reg, \
.pu_pd_reg = PU_PD_SEL_##reg, \
.pu_pd_val = status,
#define MUX_REG_7XX(reg, mode_offset, mode) .mux_reg_name = "OMAP7XX_IO_CONF_"#reg, \
.mux_reg = OMAP7XX_IO_CONF_##reg, \
.mask_offset = mode_offset, \
.mask = mode,
#define PULL_REG_7XX(reg, bit, status) .pull_name = "OMAP7XX_IO_CONF_"#reg, \
.pull_reg = OMAP7XX_IO_CONF_##reg, \
.pull_bit = bit, \
.pull_val = status,
#else
#define MUX_REG(reg, mode_offset, mode) .mux_reg = FUNC_MUX_CTRL_##reg, \
.mask_offset = mode_offset, \
.mask = mode,
#define PULL_REG(reg, bit, status) .pull_reg = PULL_DWN_CTRL_##reg, \
.pull_bit = bit, \
.pull_val = status,
#define PU_PD_REG(reg, status) .pu_pd_reg = PU_PD_SEL_##reg, \
.pu_pd_val = status,
#define MUX_REG_7XX(reg, mode_offset, mode) \
.mux_reg = OMAP7XX_IO_CONF_##reg, \
.mask_offset = mode_offset, \
.mask = mode,
#define PULL_REG_7XX(reg, bit, status) .pull_reg = OMAP7XX_IO_CONF_##reg, \
.pull_bit = bit, \
.pull_val = status,
#endif /* CONFIG_OMAP_MUX_DEBUG */
#define MUX_CFG(desc, mux_reg, mode_offset, mode, \
pull_reg, pull_bit, pull_status, \
pu_pd_reg, pu_pd_status, debug_status) \
{ \
.name = desc, \
.debug = debug_status, \
MUX_REG(mux_reg, mode_offset, mode) \
PULL_REG(pull_reg, pull_bit, pull_status) \
PU_PD_REG(pu_pd_reg, pu_pd_status) \
},
/*
* OMAP730/850 has a slightly different config for the pin mux.
* - config regs are the OMAP7XX_IO_CONF_x regs (see omap7xx.h) regs and
* not the FUNC_MUX_CTRL_x regs from hardware.h
* - for pull-up/down, only has one enable bit which is in the same register
* as mux config
*/
#define MUX_CFG_7XX(desc, mux_reg, mode_offset, mode, \
pull_bit, pull_status, debug_status)\
{ \
.name = desc, \
.debug = debug_status, \
MUX_REG_7XX(mux_reg, mode_offset, mode) \
PULL_REG_7XX(mux_reg, pull_bit, pull_status) \
PU_PD_REG(NA, 0) \
},
struct pin_config {
char *name;
const unsigned int mux_reg;
unsigned char debug;
const unsigned char mask_offset;
const unsigned char mask;
const char *pull_name;
const unsigned int pull_reg;
const unsigned char pull_val;
const unsigned char pull_bit;
const char *pu_pd_name;
const unsigned int pu_pd_reg;
const unsigned char pu_pd_val;
#if defined(CONFIG_OMAP_MUX_DEBUG) || defined(CONFIG_OMAP_MUX_WARNINGS)
const char *mux_reg_name;
#endif
};
struct omap_mux_cfg {
struct pin_config *pins;
unsigned long size;
int (*cfg_reg)(const struct pin_config *cfg);
};
#ifdef CONFIG_OMAP_MUX
/* setup pin muxing in Linux */
extern int omap1_mux_init(void);
extern int omap_mux_register(struct omap_mux_cfg *);
#else
/* boot loader does it all (no warnings from CONFIG_OMAP_MUX_WARNINGS) */
static inline int omap1_mux_init(void) { return 0; }
#endif
extern int omap2_mux_init(void);
#endif
|
