1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
|
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: cdrom: This disc doesn't have any tracks I recognize!$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: cdrom: open failed\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: apm: overridden by ACPI\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: apm: BIOS version [.0-9]+ Flags [x0-9]+ \(Driver version [.[:alnum:]]+\)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ modprobe: FATAL: Error inserting apm \([^[:space:]]+\): No such device$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: hd[[:lower:]]+: (ATAPI reset complete|drive not ready for command)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: hd[[:lower:]]+: ATAPI [0-9]+X DVD-ROM CD-R/RW drive, [0-9]+kB Cache$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: Uniform CD-ROM driver Revision: [0-9]\.[0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: eth[0-9]+: no IPv6 routers present$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: IPv6 over IPv4 tunneling driver$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: NET: Registered protocol family [0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: spurious 8259A interrupt: IRQ7\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: icmpv6: msg of unknown type$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: i2c_adapter i2c-0: sendbytes: error - bailout\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: msp34xx: I/O error #1 \((read|write) 0x[0-9a-fA-F]+/0x[0-9a-fA-F]+\)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: eth[0-9]: New link status: AP (In|Out of) Range \([0-9]+\)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: eth[0-9]: New link status: (Disconnected|Connected) \([0-9]+\)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: REJECT input_ext IN=[[:alnum:]]+ OUT= MAC=.*$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: eth[0-9]+: Media Link (Off|On [0-9]+mbps (full|half)-duplex)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ISO 9660 Extensions: Microsoft Joliet Level [0-3]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ISO 9660 Extensions: [_[:alnum:]]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ISOFS: changing to secondary root$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: agpgart: Found an AGP [0-9.]+ compliant device at [0-9:.]+\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: agpgart: Putting AGP V[0-9] device at [0-9:.]+ into [0-9]x mode$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: hub [0-9]+-[0-9]+:[0-9]+\.[0-9]+: (USB hub found|[0-9]+ ports detected)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: hub [0-9]+-[0-9]+:[0-9]+\.[0-9]+: over-current change on port [0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usb [0-9]+-[0-9]+: new full speed USB device using address [0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: hub\.c: new USB device [.:0-9-]+, assigned address [0-9]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usb [0-9]-[0-9]: USB disconnect, address [0-9]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usb.c: USB disconnect on device [.:0-9-]+ address [0-9]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usb.c: USB device [0-9]+ \(vend/prod [x/[0-9]+\) is not claimed by any active driver\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: USB Mass Storage device found at [0-9]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: Initializing USB Mass Storage driver\.\.\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: USB Mass Storage support registered\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: WARNING: USB Mass Storage data integrity not assured$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: drivers/usb/serial/usb-serial\.c: USB Serial Driver core [.[:alnum:]]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: drivers/usb/serial/usb-serial\.c: USB Serial support registered for [_[:alnum:]-]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ usb.agent\[[0-9]+\]:[[:space:]]+[_[:alnum:]-]+: (loaded successfully|already loaded)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ usb.agent\[[0-9]+\]: Keeping default configuration with [\./:[:alnum:]-]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ieee1394: Node changed: [-:0-9]+ -> [-:0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ieee1394: Node (suspended|resumed): ID:BUS\[[-:0-9]+\] GUID\[[0-9a-f]+\]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ieee1394: The root node is not cycle master capable; selecting a new root node and resetting\.\.\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ieee1394: Error parsing configrom for node [-:0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ieee1394: sbp2: Logged into SBP-2 device$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ieee1394: Node [:0-9\-]+ Max speed \[S[0-9]+\] - Max payload \[[0-9]+\]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: XFS mounting filesystem [[:alnum:]]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: Ending clean XFS mount for filesystem: [[:alnum:]]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: scsi[0-9]+ : SCSI emulation for (IEEE-1394 SBP-2 Devices|USB Mass Storage devices)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: Attached scsi removable disk sd[a-z] at scsi[0-9], channel [0-9], id [0-9], lun [0-9]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: SCSI device sd[a-z]: [0-9]+ 512-byte hdwr sectors \([0-9]+ MB\)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: sd[a-z]: Write Protect is off$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: sr[0-9]+: [^[:space:]]+ drive: [ \/[:alnum:]]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: +Vendor: [^[:space:]]+ +Model: [[:alnum:][:space:]]+ ([^[:space:]]+[[:space:]]+)?+Rev: +[.0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: +Type: +[^[:space:]]+ +ANSI SCSI revision: [0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: Attached scsi CD-ROM sr[0-9]+ at scsi[0-9], channel [0-9], id [0-9], lun [0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ scsi.agent\[[0-9]+\]: (disk|cdrom) at [\./:[:alnum:]-]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: /dev/scsi/host[0-9]/bus[0-9]/target[0-9]/lun[0-9]: p[0-9]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: keyboard: Too many NACKs -- noisy kbd cable\?$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: keyboard.c: can't emulate rawmode for keycode [0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ide-floppy driver [[:alnum:].]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ide: Assuming [0-9]+MHz system bus speed for PIO modes; override with idebus=xx$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: Uniform Multi-Platform E-IDE driver Revision: [.[:alnum:]-]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: ohci_hcd [.[:digit:]\:]+: wakeup$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usb 1-1: new low speed USB device using address [0-9]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usbcore: registered new driver [_[:lower:]-]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usb.c: registered new driver [_[:lower:]-]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: drivers/usb/input/hid-core.c: ctrl urb status [-[:digit:]]+ received$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: drivers/usb/input/hid-core.c: v[\:[:digit:].]+USB HID core driver$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ input.agent\[[0-9]+\]:[[:space:]]+(evdev|evbug|joydev): (already loaded|loaded successfully|blacklisted)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: input: USB HID v[.[:digit:]]+ Joystick \[[ [:alnum:][:punct:]]+\] on usb-[\:[:digit:].-]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: pl2303 [-:0-9.]+ PL-2303 converter detected$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usb [-:0-9]+ PL-2303 converter now attached to ttyUSB[0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: PL-2303 ttyUSB[0-9]: PL-2303 converter now disconnected from ttyUSB[0-9]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver v[.0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: Bluetooth: HCI USB driver ver [.0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: drivers\/usb\/class\/audio\.c: v[.0-9]+:USB Audio Class driver$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usbaudio: assuming that a stereo channel connected directly to a mixer is missing in search \(got .*\?\)\. Should be fine\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usbaudio: constructing mixer for Terminal [0-9]+ type 0x[0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usbaudio: device [0-9] audiocontrol interface [0-9] has [0-9] input and [0-9] output AudioStreaming interfaces$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usbaudio: device [0-9]+ interface [0-9]+ altsetting [0-9]+: format 0x[0-9]+ sratelo [0-9]+ sratehi [0-9]+ attributes 0x[0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usb_audio_parsecontrol: usb_audio_state at [[:alnum:]]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usbaudio: (registered|unregister) (dsp|mixer) [,0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usbaudio: valid (in|out)put sample rate [0-9]+$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usbaudio: warning: found [0-9] of [0-9] logical channels\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: usb 1-1: configuration #[0-9]+ chosen from [0-9]+ choices$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: sd[a-z]: Write Protect is off$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: sd[a-z]: assuming (Write Enabled|drive cache: write through)$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: SCSI subsystem initialized$
# for sun machines
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: sunmouse: Successfully adjusted to [0-9]+ baud\.$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: btaudio: driver version [0-9.]+ loaded \[digital\+analog\]$
^\w{3} [ :0-9]{11} [._[:alnum:]-]+ kernel: eth[0-9]: tx interrupt but no status$
|
