# HOWTO entry is too long

Module: 3c59x
 3c59x debug=1 options=0,,12
 
    This sets the debug message level to minimal messages,
    sets the first card to the 10baseT transceiver, the second
    to the EEPROM-set transceiver, and the third card to operate
    in full-duplex mode using its 100baseTx transceiver.
    (Note: card ordering is set by the PCI BIOS.)
    Possible media type settings:
      0  10baseT         1  10Mbs AUI    2  undefined 
      3  10base2 (BNC)   4  100base-TX   5  100base-FX
      6       MII (not yet available)    7  <Use default setting>
      8       Full-duplex bit
      16      Bus-master enable bit (experimental use only!)
    For details see the top of the source file.

Module: g_NCR5380
 g_NCR5380
 
    ncr_irq=xx      the interrupt (254 to autoprobe)
    ncr_addr=xx     the port or base address (for port or
                    memory mapped, resp.)
    ncr_dma=xx      the DMA (255 for none, 254 for overriding
    ncr_5380=1      to set up for a NCR5380 board
    ncr_53c400=1    to set up for a NCR53C400 board

    modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_5380=1
       - for a port mapped NCR5380 board or

    modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1
       - for a memory mapped NCR53C400 board with interrupts disabled.

Module: sbpcd
 sbpcd sbpcd=0x230,1

    IO address, e.g. 0x230
    
    CD-ROM interface type: 0 ... LaserMate
                           1 ... SoundBlaster
                           2 ... SoundScape
                           3 ... Teac16bit

   See Documentation/cdrom/sbpcd for more details.

Module: ipip
NoParams:
 ipip 

Module: tulip
NoParams:
 tulip 

Module: umsdos
NoParams:
 umsdos

Module: hisax
 hisax type=aa io=0xbbb irq=cc mem=0xddddd protocol=e id=line0
 
   Card types are:
   1 Teles 16.0         (irq,mem,io)  7 ELSA Quickstep 1000 (irq,io)
   2 Teles  8.0         (irq,mem)    10 ELSA PCMCIA         (irq,io)
   3 Teles 16.3 non-PnP (irq,io)      8 Teles 16.3 PCMCIA   (irq,io)
   4 Creatix/Teles PnP  (irq,io0,io1) 9 ITK ix1-micro Rev.2 (irq,io)
   5 AVM A1 (Fritz)     (irq,io)      
   6 ELSA PCC/PCF (io or nothing for autodetect)
   - If any of io, irq, mem are not applicable, leave it out completely.
   - protocol is 1 for German 1TR6, 2 for EDSS1 (Euro ISDN) and 3 for
     leased lines.
   - See /usr/src/linux/Documentation/isdn/README.HiSax for details, e.g.
     two cards

Module: ne
 ne 
 
 io = 0          (ISA cards explicitly *require* an \\\"io=0xNNN\\\" value)
 irq = 0         (Tries to determine configured IRQ via autoIRQ)
 Depends on 8390.o

Module: eepro
 eepro

 io = 0x200
 irq = 0
 (Probes ports: 0x200, 0x240, 0x280, 0x2C0, 0x300, 0x320, 0x340, 0x360)
 Some models REQUIRE that you specify the IRQ/IOport.

Module: raid1
NoParams:
 raid1 
 

Module: raid5
NoParams:
 raid5 
 

Module: paride
NoParms:
 paride


Module: aten
NoParms:
 aten


Module: bpck
NoParms:
 bpck


Module: comm
NoParms:
 comm


Module: dstr
NoParms:
 dstr


Module: epat
NoParms:
 epat


Module: epia
NoParms:
 epia


Module: fit2
NoParms:
 fit2


Module: fit3
NoParms:
 fit3


Module: frpw
NoParms:
 frpw


Module: kbic
NoParms:
 kbic


Module: ktti
NoParms:
 ktti


Module: on20
NoParms:
 on20


Module: on26
NoParms:
 on26


Module: pcd
NoParms:
 pcd


Module: pd
NoParms:
 pd


Module: pf
NoParms:
 pf


Module: pt
NoParms:
 pt


Module: pg
NoParms:
 pg

Module: ip_masq_cuseeme
NoParms:
 ip_masq_cuseeme 


Module: ip_masq_ftp
NoParms:
 ip_masq_ftp 


Module: ip_masq_irc
NoParms:
 ip_masq_irc 


Module: ip_masq_quake
NoParms:
 ip_masq_quake 


Module: ip_masq_raudio
NoParms:
 ip_masq_raudio 


Module: ip_masq_vdolive
NoParms:
 ip_masq_vdolive 


Module shaper
NoParams:
 shaper 

Module: nls_cp437
NoParms:
 nls_cp437


Module: nls_cp737
NoParms:
 nls_cp737


Module: nls_cp775
NoParms:
 nls_cp775


Module: nls_cp850
NoParms:
 nls_cp850


Module: nls_cp852
NoParms:
 nls_cp852


Module: nls_cp855
NoParms:
 nls_cp855


Module: nls_cp857
NoParms:
 nls_cp857


Module: nls_cp860
NoParms:
 nls_cp860


Module: nls_cp861
NoParms:
 nls_cp861


Module: nls_cp862
NoParms:
 nls_cp862


Module: nls_cp863
NoParms:
 nls_cp863


Module: nls_cp864
NoParms:
 nls_cp864


Module: nls_cp865
NoParms:
 nls_cp865


Module: nls_cp866
NoParms:
 nls_cp866


Module: nls_cp869
NoParms:
 nls_cp869


Module: nls_cp874
NoParms:
 nls_cp874


Module: nls_iso8859_1
NoParms:
 nls_iso8859_1


Module: nls_iso8859_2
NoParms:
 nls_iso8859_2


Module: nls_iso8859_3
NoParms:
 nls_iso8859_3


Module: nls_iso8859_4
NoParms:
 nls_iso8859_4


Module: nls_iso8859_5
NoParms:
 nls_iso8859_5


Module: nls_iso8859_6
NoParms:
 nls_iso8859_6


Module: nls_iso8859_7
NoParms:
 nls_iso8859_7


Module: nls_iso8859_8
NoParms:
 nls_iso8859_8


Module: nls_iso8859_9
NoParms:
 nls_iso8859_9


Module: nls_koi8_r
NoParms:
 nls_koi8_r

Module: 3c574_cs
NoParams:

    Supported Cards: This driver is BUGGY !
      - 3Com 3c574TX

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: 3c589_cs
NoParams:

    Supported Cards:
      - 3Com 3c589, 3c589B, 3c589C, 3c589D, 3CCE589E, 3CXE589D
      - Farallon EtherWave, EtherMac

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: fmvj18x_cs
NoParams:

    Supported Cards:
      - CONTEC C-NET(PC)C
      - Eagle NE200 Ethernet
      - Eiger Labs EPX-10BT, EPX-ET 10BT, EPX-ET 10TZ
      - Fujitsu FMV-J181, FMV-J182, FMV-J182A, Towa LA501
      - Hitachi HT-4840-11 EtherCard
      - NextCom NC5310
      - RATOC REX-9822, REX-5588A/W
      - TDK LAC-CD02x, LAK-CD021, LAK-CD022A, LAK-CD021AX Ethernet

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: nmclan_cs
NoParams:

    Supported Cards:
      - New Media EthernetLAN
      - New Media LiveWire	[ NOT the LiveWire+ ]

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: pcnet_cs
NoParams:

    Supported Cards: 
       - Nearly all NE2000 kompatible Cards (10/100baseT)
       - Most Mutlifunction Ethernet/Modem Cards
       You should try this driver if your Card is not listed
       as supported. For more information read the Dokumentation
       (/usr/doc/pcmcia/)

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: smc91c92_cs
NoParams:

    Supported Cards:
      - Megahertz XJ10BT, XJ10BC, CC10BT Ethernet
      - New Media BASICS Ethernet
      - Ositech Four of Diamonds
      - SMC 8020BT EtherEZ	[ NOT the EliteCard! ]

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: xirc2ps_cs
NoParams:

    Supported Cards:
      - Compaq Ethernet Adapter
      - Xircom CreditCard CE2
      - Compaq Netelligent 10/100
      - Intel EtherExpress PRO/100 [ 16-bit, NOT 32-bit ]
      - Toshiba Advanced Network 10/100
      - Xircom CreditCard CE3 [ beware: new cards may not work ]

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: 3c575_cb 
NoParams:

    Supported Cards:
      - 3Com 3c575TX, 3CCFE575B, 3CXFE575B CardBus

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: epic_cb
NoParams:

    Supported Cards: This driver requires a 2.2 kernel, experimental!
      - Ositech Seven of Spades CardBus

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: tulip_cb
NoParams:

    Supported Cards: This driver requires a 2.2 kernel, experimental!
       - Linksys EtherFast CardBus
       - TDK NetworkFlyer LAK-CB100X CardBus

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: ibmtr_cs
NoParams:

    Supported Cards:
      - 3Com 3c389 TokenLink Velocity
      - 3Com 3c689 TokenLink III
      - IBM Token Ring Adapter
      - IBM Turbo 16/4 Token Ring

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: wavelan_cs
NoParams:

    Supported Cards: 
      - AT&T / NCR / Lucent WaveLAN version 2.0
      - DEC RoamAbout/DS
      The WaveLAN/IEEE is NOT supported 

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: netwave_cs
NoParams:

    Supported Cards: 
      - Xircom CreditCard Netwave

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: serial_cs
NoParams:

    Supported Cards:
      Nearly all Modem Cards (no so-called "WinModems") simple serial port cards, 
      and digital cellular modems should work. 
      ISDN modems that emulate a standard UART are also supported. 

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: sram_mtd
NoParams:

    Supported Cards:
      ALL SRAM Cards should work, unsupported Cards 
      can be read but not written.

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: aha152x_cs
NoParams:

    Supported Cards:
      - Adaptec APA-1460, APA-1450A, APA-1460A, APA-1460B SlimSCSI
      - Iomega Zip and Jaz Cards
      - New Media Bus Toaster SCSI	        [ older cards ]
      - New Media Toast 'n Jam		[ SCSI only ]
      - Noteworthy Bus Toaster SCSI
      - Sony CD-ROM Discman PRD-250

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module:	fdomain_cs
NoParams:

    Supported Cards:
      - Future Domain SCSI2GO
      - IBM SCSI
      - Simple Technologies SCSI

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module:	qlogic_cs
NoParams:

    Supported Cards:
      - Eiger Labs SCSI
      - MACNICA mPS110, mPS110-LP SCSI
      - NEC PC-9801N-J03R
      - Qlogic FastSCSI
      - Panasonic KXL-D740, KXL-DN740A, KXL-DN740A-NB 4X CD-ROM
      - Raven CD-Note 4X
      - RATOC REX-9530 SCSI-2
      - Toshiba NWB0107ABK, SCSC200B

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: apa1480_cb 
NoParams:

    Supported Cards:
      - Adaptec SlimSCSI 1480 CardBus

    This driver works for kernels 2.1.90-2.1.124, and 2.1.132 and
    later.  Also experimental!

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: ide_cs
NoParams:

    Supported Cards:
      Most Cards should work fine, including adapters for external
      IDE devices.
      Only very old Western Digital are not supported.

    Parameters (if needed) must be specific in /etc/pcmcia/conf 
    or /etc/pcmcia/conf.opts !

Module: plip
 plip
 
    parport=PORT	parallel port number