1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
|
#This is an example configuration file for mumudvb using partial autoconfiguration and sending sap announces
#All the commented lines are optionnal (except for tuning you have to match your system)
#To set unicast HTTP refer to README_CONF and README
#
#------------ TUNING -------------
#The DVB/ATSC card we want to use
#card=2
#The Transponder frequency
freq=12597
# ---- SATELLITE (DVB-S) -----
#The polarisation (can be h, v, l, r)
pol=V
#The symbol rate
srate=27500
# ----- CABLE (DVB-C) ----
#The symbol rate
#srate=27500
# ---- TERRESTRIAL (DVB-T) -----
#For DVB-T if the bandwith is 8MHz you don't have to set other parameters
#
# ----- ATSC ----
#For ATSC you could have to set the modulation if it's different from VSB_8
#
#---------- AUTOCONFIGURATION -----------
#We want the partial autoconfiguration (ie we discover the pids of the defined channels)
autoconfiguration=partial
#
#--------- NETWORKING --------------
#Do we want to have the same port for all the channels ?
common_port=1234
#
#Do we need to change the default multicast TTL (if you have routers, default value : 2) ?
#multicast_ttl=10
#
#--------- SAP ANNOUNCES --------------
#The sap announces are sent automatically with full autoconfiguration
#Do we want to send the announces ?
sap=1
#
#What is the default playlist group for the SAP announces (optionnal) ?
sap_default_group=My channels
#Who is the organisation wich send the stream (optionnal) ?
#sap_organisation=my_organisation
#The intervall between the SAP announces in second (default 5)
#sap_interval=10
# ---------- PAT REWRITING ----------
#If some of the clients are set top boxes we will probably need to rewrite the PAT pid
#rewrite_pat=1
#
# ---------- SCRAMBLED CHANNELS ----------
#Do we want hadware descrambling ?
#cam_support=1
#
#If you have multiple CAMs you can specify the number of the one wich will be used
#cam_number=2
#
#
# ----------------------- THE CHANNELS ---------------------
#
#For each channel you have to define :
# * The ip address
# * The port (if you didn't used common_port)
# * The name
# * At least the PMT pid (if there is more than one pid, no autoconfiguration will be done for this chanel)
#
#Ip address
ip=239.210.203.200
#Name of the channel
name=BBC World News
#The PMT pid
pids=1027
#
#
ip=239.210.203.201
name=Euronews
pids=1034
#
#A channel WITHOUT autoconfiguration
ip=239.210.203.202
name=eng Euronews
pids=1034 2221 2232 768
#
#A scrambled channel, add cam_support=1 before the channel lists
#ip=239.210.203.203
#name=Japan satellite TV
#cam_pmt_pid=1037
#pids=1037
|
