1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
|
.TH ENERGIZERUPS 8 "Sun Aug 24 2003" "" "Network UPS Tools (NUT)"
.SH NAME
energizerups \- Driver for Energizer (Megatec protocol over "USB To RS232 Interface (V1.0) BaudRate 2400bps") UPS equipment
.SH NOTE
This man page only documents the hardware\(hyspecific features of the
energizerups driver. For information about the core driver, see
\fBnutupsdrv\fR(8).
.SH SUPPORTED HARDWARE
.B energizerups
supports Energizer models such as the ER\(hyHMOF600 and ER\(hyOF800.
At the time of this writing, the driver was tested only with these two
models. Other Energizer models that use the same USB interface should also
work, but they have not been tested for compatibility.
.SH PREREQUISITES
This driver is Linux\(hyspecific. It is not designed to work on other
operating systems.
In order for this driver to work, USB and HID support must be present on
your system. As a minimum, this means that the following kernel drivers
must be loaded:
.RS
hid
.br
usb\(hyuhci
.br
usbcore
.RE
In place of usb\(hyuhci, you may have another host controller module loaded,
as appropriate for your hardware.
In version 2.4.21 and possibly other versions of the Linux kernel, the
hiddev driver refuses to take control of HID devices that are also
recognized as input peripherals. Unfortunately, this also applies to these
Energizer UPS models. One solution to this problem is to compile a kernel
with the CONFIG_HID_USBINPUT option turned off. An alternative is to
modify the kernel with a simple patch. In drivers/usb/hiddev.c, in
the function hiddev_connect(), the line
.RS
if (!IS_INPUT_APPLICATION(hid\(hy>application[i]))
.RE
must be removed or commented out, and the driver and/or the kernel must
be recompiled.
.B energizerups
also requires that device nodes for the UPS HID device be created. If these
don't exist on your system, you can create them using the following commands:
.RS
mkdir /dev/usb
.br
mkdir /dev/usb/hid
.br
mknod /dev/usb/hid/hiddev0 c 180 96
.br
mknod /dev/usb/hid/hiddev1 c 180 97
.br
mknod /dev/usb/hid/hiddev2 c 180 98
.br
mknod /dev/usb/hid/hiddev3 c 180 99
.RE
If your system uses the devfs file system, the appropriate node may be
created automatically by the system when the UPS is connected.
.SH CHECKING THE HARDWARE
You can verify that the UPS is connected and recognized by your system by
mounting the usbfs file system (if it is not mounted already) and then
listing all USB devices:
.RS
mount none /proc/bus/usb \-t usbfs
.br
cat /proc/bus/usb/devices
.RE
In this file, the following line should be seen:
.B "S: Product=USB To RS232 Interface (V1.0) BaudRate 2400bps"
This line indicates the presence of the USB\(hyto\(hyserial converter that is
used by these Energizer UPS models.
.SH EXTRA ARGUMENTS
This driver does not support any extra settings in the
\fBups.conf\fR(5).
.SH BUGS
The battery percentage is derived from the voltage data that the UPS
returns, since the UPS doesn't return that value directly. On some
hardware, the charge will remain at 100% for a long time and then drops
quickly shortly before the battery runs out. You can confirm from the
battery.voltage readings that this is a problem with the UPS and not
this driver.
Voltage/charge characteristics are derived from a manual calibration with
an ER\(hyHMOF600. Due to hardware differences, the charge percentage reports
may be very inaccurate.
Dead/broken batteries can't be reported reliably. If your UPS kills the
load instantly or within seconds of starting the inverter, your batteries
probably need to be replaced.
.SH AUTHOR
Viktor Toth
.B (http://www.vttoth.com/)
.SH SEE ALSO
.SS The core driver:
\fBnutupsdrv\fR(8)
.SS Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
|
