1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
|
/* @(#)error.h 5.18 93/07/30 16:39:48, Srini, AMD */
/******************************************************************************
* Copyright 1991 Advanced Micro Devices, Inc.
*
* This software is the property of Advanced Micro Devices, Inc (AMD) which
* specifically grants the user the right to modify, use and distribute this
* software provided this notice is not removed or altered. All other rights
* are reserved by AMD.
*
* AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS
* SOFTWARE. IN NO EVENT SHALL AMD BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
* DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR
* USE OF THIS SOFTWARE.
*
* So that all may benefit from your experience, please report any problems
* or suggestions about this software to the 29K Technical Support Center at
* 800-29-29-AMD (800-292-9263) in the USA, or 0800-89-1131 in the UK, or
* 0031-11-1129 in Japan, toll free. The direct dial number is 512-462-4118.
*
* Advanced Micro Devices, Inc.
* 29K Support Products
* Mail Stop 573
* 5900 E. Ben White Blvd.
* Austin, TX 78741
* 800-292-9263
*****************************************************************************
* Engineer: Srini Subramanian.
*****************************************************************************
** This header file describes the errors which may be returned
** by the monitor.
**
** All of the #define'ed error codes below begin with the leters
** "EM" (for "Error Monitor"). This should avoid colisions with
** other #define's in the system.
**
*****************************************************************************
*/
#ifndef _ERROR_H_INCLUDED_
#define _ERROR_H_INCLUDED_
/* General errors */
#define EMUSAGE 1 /* Bad args / flags */
#define EMFAIL 2 /* Unrecoverable error */
#define EMBADADDR 3 /* Illegal address */
#define EMBADREG 4 /* Illegal register */
#define EMSYNTAX 5 /* Illegal command syntax */
#define EMACCESS 6 /* Could not access memory */
#define EMALLOC 7 /* Could not allocate memory */
#define EMTARGET 8 /* Unknown target type */
#define EMHINIT 9 /* Could not initialize host */
#define EMCOMM 10 /* Could not open communication channel */
/* Message errors */
#define EMBADMSG 11 /* Unknown message type */
#define EMMSG2BIG 12 /* Message to large for buffer */
#define EMRESET 13 /* Could not RESET target */
#define EMCONFIG 14 /* Could not get target CONFIG */
#define EMSTATUS 15 /* Could not get target STATUS */
#define EMREAD 16 /* Could not READ target memory */
#define EMWRITE 17 /* Could not WRITE target memory */
#define EMBKPTSET 18 /* Could not set breakpoint */
#define EMBKPTRM 19 /* Could not remove breakpoint */
#define EMBKPTSTAT 20 /* Could not get breakpoint status */
#define EMBKPTNONE 21 /* All breakpoints in use */
#define EMBKPTUSED 22 /* Breakpoints already in use */
#define EMCOPY 23 /* Could not COPY target memory */
#define EMFILL 24 /* Could not FILL target memory */
#define EMINIT 25 /* Could not initialize target memory */
#define EMGO 26 /* Could not start execution */
#define EMSTEP 27 /* Could not single step */
#define EMBREAK 28 /* Could not BREAK */
#define EMHIF 29 /* Could not perform HIF service */
#define EMCHANNEL0 30 /* Could not read CHANNEL0 */
#define EMCHANNEL1 31 /* Could not write CHANNEL1 */
/* COFF file loader errors */
#define EMOPEN 32 /* Could not open COFF file */
#define EMHDR 33 /* Could not read COFF header */
#define EMMAGIC 34 /* Bad magic number */
#define EMAOUT 35 /* Could not read COFF a.out header */
#define EMSCNHDR 36 /* Could not read COFF section header */
#define EMSCN 37 /* Could not read COFF section */
#define EMCLOSE 38 /* Could not close COFF file */
/* Log file errors */
#define EMLOGOPEN 39 /* Could not open log file */
#define EMLOGREAD 40 /* Could not read log file */
#define EMLOGWRITE 41 /* Could not write to log file */
#define EMLOGCLOSE 42 /* Could not close log file */
/* Command file errors */
#define EMCMDOPEN 43 /* Could not open command file */
#define EMCMDREAD 44 /* Could not read command file */
#define EMCMDWRITE 45 /* Could not write to command file */
#define EMCMDCLOSE 46 /* Could not close comand file */
#define EMTIMEOUT 47 /* Host timed out waiting for a message */
#define EMCOMMTYPE 48 /* A '-t' flag must be specified */
#define EMCOMMERR 49 /* Communication error */
#define EMBAUD 50 /* Invalid baud rate specified */
#define EMTIPINIT 51 /* Failed TIP init */
#define EMIOSETF 52 /* I/O set up failure */
#define EMIORESETF 53 /* I/O reset failure */
#define EMLOADF 54 /* Loading COFF file failed */
#define EMNOFILE 55 /* No program to run. */
#define EMECHOPEN 56 /* Could not open echo file */
#define EMCTRLC 57 /* Ctrl-C encountered */
#define EMNOSUCHCMD 58 /* Unrecognized command */
#define EMNOPROCESS 59 /* create process */
#define EMNOTCOMP 60 /* Not compatible */
#define EMFATAL 61 /* UDIWait failed */
#define EMNOINITP 62 /* No initialize process */
#define EMDOSERR 63 /* DOS err on escape */
#define EMSYSERR 64 /* system err on escape */
#define EMINVECHOFILE 65 /* invalid echo file */
#define EMCMDFILENEST 66 /* command file nesting */
extern char *error_msg[];
#endif /* _ERROR_H_INCLUDED_ */
|
