1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
|
:Version: 0.12.0
:Copyright: 2006-2013 ARM Limited
:Title: pyocd-gdbserver
:subtitle: ARM Cortex-M programming tool
:Manual section: "1"
Description
============
``pyocd-gdbserver`` is an ARM Cortex-M programming tool
Summary
#######
pyOCD is an Open Source python based library for programming
and debugging ARM Cortex-M microcontrollers using CMSIS-DAP.
Includes support for flashing new binaries, resetting the device,
halt, step, resume read/write memory and set/remove breakpoints.
Support
#######
Firmware files included in the upstream source are NOT included in the
Debian package due to a lack of source code. Target files can be
downloaded separately from https://github.com/mbedmicro/pyOCD/tree/master/binaries
Available targets for use with --target option: lpc824, kinetis, w7500,
kv11z7, lpc4088qsb, kv10z7, k20d50m, ncs36510, kl28z, kl25z, k82f25615,
k28f15, maxwsnenv, max32600mbed, k22fa12, lpc4088, lpc4330, ke18f16, kl46z,
stm32f103rc, kl82z7, lpc54114, kl43z4, kl26z, lpc11xx_32, lpc800, rtl8195am,
kl05z, lpc1768, kw41z4, lpc4088dm, stm32f051, cortex_m, lpc11u24, kl02z,
kw01z4, k64f, k22f, ke15z7, nrf51, nrf52, kl27z4, kw40z4, k66f18
Usage
#####
usage: pyocd-gdbserver [-h] [--version] [-p PORT_NUMBER] [-T TELNET_PORT] [--allow-remote] [-b BOARD_ID] [-l] [--list-targets]
[--json] [-d LEVEL] [-t TARGET] [-n] [-r] [-C VECTOR_CATCH] [-s] [-f FREQUENCY] [-o] [-bh]
[-ce | -se] [-u] [-hp] [-fp] [-S] [-G] [-c CMD [CMD ...]] [-da DAPARG [DAPARG ...]]
PyOCD GDB Server
optional arguments:
-h, --help show this help message and exit
--version show program's version number and exit
-p PORT_NUMBER, --port PORT_NUMBER Write the port number that GDB server will open.
-T TELNET_PORT, --telnet-port TELNET_PORT Specify the telnet port for semihosting.
--allow-remote Allow remote TCP/IP connections (default is no).
-b BOARD_ID, --board BOARD_ID Connect to board by board id. Use -l to list all connected boards.
-l, --list List all connected boards.
--list-targets List all available targets.
--json Output lists in JSON format. Only applies to --list and --list-targets.
-d LEVEL, --debug LEVEL Set the level of system logging output. Supported choices are: debug, info, warning, critical, error
-t TARGET, --target TARGET Override target to debug. -n, --nobreak Disable halt at hardfault handler. (Deprecated)
-r, --reset-break Halt the target when reset. (Deprecated)
-C VECTOR_CATCH, --vector-catch VECTOR_CATCH Enable vector catch sources, one letter per enabled source in any order, or 'all' or 'none'. (h=hard
fault, b=bus fault, m=mem fault, i=irq err, s=state
err, c=check err, p=nocp, r=reset, a=all, n=none).
(Default is hard fault.)
-s, --step-int Allow single stepping to step into interrupts.
-f FREQUENCY, --frequency FREQUENCY Set the SWD clock frequency in Hz.
-o, --persist Keep GDB server running even after remote has detached.
-bh, --soft-bkpt-as-hard Replace software breakpoints with hardware breakpoints.
-ce, --chip_erase Use chip erase when programming.
-se, --sector_erase Use sector erase when programming.
-u, --unlock Unlock the device.
-hp, --hide_progress Don't display programming progress.
-fp, --fast_program Use only the CRC of each page to determine if it already has the same data.
-S, --semihosting Enable semihosting.
-G, --gdb-syscall Use GDB syscalls for semihosting file I/O.
-c CMD [CMD ...], --command CMD [CMD ...] Run command (OpenOCD compatibility).
-da DAPARG [DAPARG ...], --daparg DAPARG [DAPARG ...] Send setting to DAPAccess layer.
|
