1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
|
#
# Copyright 2019 aiohomekit team
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
#
from aiohomekit.enum import EnumWithDescription
class HapStatusCode(EnumWithDescription):
SUCCESS = 0, "This specifies a success for the request."
INSUFFICIENT_PRIVILEGES = -70401, "Request denied due to insufficient privileges."
UNABLE_TO_COMMUNICATE = (
-70402,
"Unable to communicate with requested service, e.g. the power to the accessory was turned off.",
)
RESOURCE_BUSY = -70403, "Resource is busy, try again."
CANT_WRITE_READ_ONLY = -70404, "Cannot write to read only characteristic."
CANT_READ_WRITE_ONLY = -70405, "Cannot read from a write only characteristic."
NOTIFICATION_NOT_SUPPORTED = (
-70406,
"Notification is not supported for characteristic.",
)
OUT_OF_RESOURCES = -70407, "Out of resources to process request."
TIMED_OUT = -70408, "Operation timed out."
RESOURCE_NOT_EXIST = -70409, "Resource does not exist."
INVALID_VALUE = -70410, "Accessory received an invalid value in a write request."
INSUFFICIENT_AUTH = -70411, "Insufficient Authorization."
NOT_ALLOWED_IN_CURRENT_STATE = -70412, "Not allowed in current state"
def to_status_code(status_code: int) -> HapStatusCode:
# Some HAP implementations return positive values for error code (myq)
return HapStatusCode(abs(status_code) * -1)
class _HapBleStatusCodes:
"""
This data is taken from Table 6-26 HAP Status Codes on page 116.
"""
SUCCESS = 0x00
UNSUPPORTED_PDU = 0x01
MAX_PROCEDURES = 0x02
INSUFFICIENT_AUTHORIZATION = 0x03
INVALID_INSTANCE_ID = 0x04
INSUFFICIENT_AUTHENTICATION = 0x05
INVALID_REQUEST = 0x06
def __init__(self) -> None:
self._codes = {
_HapBleStatusCodes.SUCCESS: "The request was successful.",
_HapBleStatusCodes.UNSUPPORTED_PDU: "The request failed as the HAP PDU was not recognized or supported.",
_HapBleStatusCodes.MAX_PROCEDURES: "The request failed as the accessory has reached the limit on"
" the simultaneous procedures it can handle.",
_HapBleStatusCodes.INSUFFICIENT_AUTHORIZATION: "Characteristic requires additional authorization data.",
_HapBleStatusCodes.INVALID_INSTANCE_ID: "The HAP Request's characteristic Instance Id did not match"
" the addressed characteristic's instance Id",
_HapBleStatusCodes.INSUFFICIENT_AUTHENTICATION: "Characterisitc access required a secure session to be"
" established.",
_HapBleStatusCodes.INVALID_REQUEST: "Accessory was not able to perform the requested operation",
}
self._categories_rev = {self._codes[k]: k for k in self._codes.keys()}
def __getitem__(self, item):
if item in self._codes:
return self._codes[item]
raise KeyError(f"Item {item} not found")
HapBleStatusCodes = _HapBleStatusCodes()
|
