1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
|
.. _paste_chapter:
PasteDeploy Configuration Files
===============================
Packages generated via a :term:`scaffold` make use of a system created by Ian
Bicking named :term:`PasteDeploy`. PasteDeploy defines a way to declare
:term:`WSGI` application configuration in an ``.ini`` file.
Pyramid uses this configuration file format as input to its :term:`WSGI` server
runner ``pserve``, as well as other commands such as ``pviews``, ``pshell``,
``proutes``, and ``ptweens``.
PasteDeploy is not a particularly integral part of Pyramid. It's possible to
create a Pyramid application which does not use PasteDeploy at all. We show a
Pyramid application that doesn't use PasteDeploy in :ref:`firstapp_chapter`.
However, all Pyramid scaffolds render PasteDeploy configuration files, to
provide new developers with a standardized way of setting deployment values,
and to provide new users with a standardized way of starting, stopping, and
debugging an application.
This chapter is not a replacement for documentation about PasteDeploy; it only
contextualizes the use of PasteDeploy within Pyramid. For detailed
documentation, see http://pythonpaste.org/deploy/.
PasteDeploy
-----------
:term:`PasteDeploy` is the system that Pyramid uses to allow :term:`deployment
settings` to be specified using an ``.ini`` configuration file format. It also
allows the ``pserve`` command to work. Its configuration format provides a
convenient place to define application :term:`deployment settings` and WSGI
server settings, and its server runner allows you to stop and start a Pyramid
application easily.
.. _pastedeploy_entry_points:
Entry Points and PasteDeploy ``.ini`` Files
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In the :ref:`project_narr` chapter, we breezed over the meaning of a
configuration line in the ``deployment.ini`` file. This was the ``use =
egg:MyProject`` line in the ``[app:main]`` section. We breezed over it because
it's pretty confusing and "too much information" for an introduction to the
system. We'll try to give it a bit of attention here. Let's see the config
file again:
.. literalinclude:: MyProject/development.ini
:language: ini
:linenos:
The line in ``[app:main]`` above that says ``use = egg:MyProject`` is actually
shorthand for a longer spelling: ``use = egg:MyProject#main``. The ``#main``
part is omitted for brevity, as ``#main`` is a default defined by PasteDeploy.
``egg:MyProject#main`` is a string which has meaning to PasteDeploy. It points
at a :term:`setuptools` :term:`entry point` named ``main`` defined in the
``MyProject`` project.
Take a look at the generated ``setup.py`` file for this project.
.. literalinclude:: MyProject/setup.py
:language: python
:linenos:
Note that ``entry_points`` is assigned a string which looks a lot like an
``.ini`` file. This string representation of an ``.ini`` file has a section
named ``[paste.app_factory]``. Within this section, there is a key named
``main`` (the entry point name) which has a value ``myproject:main``. The
*key* ``main`` is what our ``egg:MyProject#main`` value of the ``use`` section
in our config file is pointing at, although it is actually shortened to
``egg:MyProject`` there. The value represents a :term:`dotted Python name`
path, which refers to a callable in our ``myproject`` package's ``__init__.py``
module.
The ``egg:`` prefix in ``egg:MyProject`` indicates that this is an entry point
*URI* specifier, where the "scheme" is "egg". An "egg" is created when you run
``setup.py install`` or ``setup.py develop`` within your project.
In English, this entry point can thus be referred to as a "PasteDeploy
application factory in the ``MyProject`` project which has the entry point
named ``main`` where the entry point refers to a ``main`` function in the
``mypackage`` module". Indeed, if you open up the ``__init__.py`` module
generated within any scaffold-generated package, you'll see a ``main``
function. This is the function called by :term:`PasteDeploy` when the
``pserve`` command is invoked against our application. It accepts a global
configuration object and *returns* an instance of our application.
.. _defaults_section_of_pastedeploy_file:
``[DEFAULT]`` Section of a PasteDeploy ``.ini`` File
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
You can add a ``[DEFAULT]`` section to your PasteDeploy ``.ini`` file. Such a
section should consist of global parameters that are shared by all the
applications, servers, and :term:`middleware` defined within the configuration
file. The values in a ``[DEFAULT]`` section will be passed to your
application's ``main`` function as ``global_config`` (see the reference to the
``main`` function in :ref:`init_py`).
|
