1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489
|
#!/usr/bin/env perl
use strict;
use warnings;
BEGIN {
use FindBin;
use lib "$FindBin::Bin/lib";
}
use Getopt::Long qw(:config no_auto_abbrev);
use List::Util qw(first);
use POSIX qw(setlocale LC_NUMERIC);
use Slic3r;
use Time::HiRes qw(gettimeofday tv_interval);
$|++;
our %opt = ();
my %cli_options = ();
{
my %options = (
'help' => sub { usage() },
'version' => sub { print "$Slic3r::VERSION\n"; exit 0 },
'debug' => \$Slic3r::debug,
'gui' => \$opt{gui},
'o|output=s' => \$opt{output},
'save=s' => \$opt{save},
'load=s@' => \$opt{load},
'autosave=s' => \$opt{autosave},
'ignore-nonexistent-config' => \$opt{ignore_nonexistent_config},
'no-plater' => \$opt{no_plater},
'gui-mode=s' => \$opt{gui_mode},
'datadir=s' => \$opt{datadir},
'export-svg' => \$opt{export_svg},
'merge|m' => \$opt{merge},
'repair' => \$opt{repair},
'cut=f' => \$opt{cut},
'info' => \$opt{info},
'scale=f' => \$opt{scale},
'rotate=i' => \$opt{rotate},
'duplicate=i' => \$opt{duplicate},
'duplicate-grid=s' => \$opt{duplicate_grid},
);
foreach my $opt_key (keys %{$Slic3r::Config::Options}) {
my $cli = $Slic3r::Config::Options->{$opt_key}->{cli} or next;
# allow both the dash-separated option name and the full opt_key
$options{ "$opt_key|$cli" } = \$cli_options{$opt_key};
}
GetOptions(%options) or usage(1);
}
# load configuration files
my @external_configs = ();
if ($opt{load}) {
foreach my $configfile (@{$opt{load}}) {
if (-e $configfile) {
push @external_configs, Slic3r::Config->load($configfile);
} elsif (-e "$FindBin::Bin/$configfile") {
printf STDERR "Loading $FindBin::Bin/$configfile\n";
push @external_configs, Slic3r::Config->load("$FindBin::Bin/$configfile");
} else {
$opt{ignore_nonexistent_config} or die "Cannot find specified configuration file ($configfile).\n";
}
}
}
# process command line options
my $cli_config = Slic3r::Config->new;
foreach my $c (@external_configs, Slic3r::Config->new_from_cli(%cli_options)) {
$c->normalize; # expand shortcuts before applying, otherwise destination values would be already filled with defaults
$cli_config->apply($c);
}
# save configuration
if ($opt{save}) {
$cli_config->save($opt{save});
}
# apply command line config on top of default config
my $config = Slic3r::Config->new_from_defaults;
$config->apply($cli_config);
# launch GUI
my $gui;
if (!@ARGV && !$opt{save} && eval "require Slic3r::GUI; 1") {
{
no warnings 'once';
$Slic3r::GUI::datadir = $opt{datadir};
$Slic3r::GUI::no_plater = $opt{no_plater};
$Slic3r::GUI::mode = $opt{gui_mode};
$Slic3r::GUI::autosave = $opt{autosave};
}
$gui = Slic3r::GUI->new;
setlocale(LC_NUMERIC, 'C');
$gui->{skeinpanel}->load_config_file($_) for @{$opt{load}};
$gui->{skeinpanel}->load_config($cli_config);
$gui->MainLoop;
exit;
}
die $@ if $@ && $opt{gui};
if (@ARGV) { # slicing from command line
$config->validate;
if ($opt{repair}) {
foreach my $file (@ARGV) {
die "Repair is currently supported only on STL files\n"
if $file !~ /\.stl$/i;
my $output_file = $file;
$output_file =~ s/\.(stl)$/_fixed.obj/i;
my $tmesh = Slic3r::TriangleMesh->new;
$tmesh->ReadSTLFile($file);
$tmesh->repair;
$tmesh->WriteOBJFile($output_file);
}
exit;
}
if ($opt{cut}) {
foreach my $file (@ARGV) {
my $model = Slic3r::Model->read_from_file($file);
$model->add_default_instances;
my $mesh = $model->mesh;
$mesh->translate(0, 0, -$mesh->bounding_box->z_min);
my $upper = Slic3r::TriangleMesh->new;
my $lower = Slic3r::TriangleMesh->new;
$mesh->cut($opt{cut}, $upper, $lower);
$upper->repair;
$lower->repair;
$upper->write_ascii("${file}_upper.stl")
if $upper->facets_count > 0;
$lower->write_ascii("${file}_lower.stl")
if $lower->facets_count > 0;
}
exit;
}
while (my $input_file = shift @ARGV) {
my $model;
if ($opt{merge}) {
my @models = map Slic3r::Model->read_from_file($_), $input_file, (splice @ARGV, 0);
$model = Slic3r::Model->merge(@models);
} else {
$model = Slic3r::Model->read_from_file($input_file);
}
if ($opt{info}) {
$model->print_info;
next;
}
if (defined $opt{duplicate_grid}) {
$opt{duplicate_grid} = [ split /[,x]/, $opt{duplicate_grid}, 2 ];
}
my $sprint = Slic3r::Print::Simple->new(
scale => $opt{scale} // 1,
rotate => $opt{rotate} // 0,
duplicate => $opt{duplicate} // 1,
duplicate_grid => $opt{duplicate_grid} // [1,1],
status_cb => sub {
my ($percent, $message) = @_;
printf "=> %s\n", $message;
},
output_file => $opt{output},
);
$sprint->apply_config($config);
$sprint->set_model($model);
if ($opt{export_svg}) {
$sprint->export_svg;
} else {
my $t0 = [gettimeofday];
$sprint->export_gcode;
# output some statistics
{
my $duration = tv_interval($t0);
printf "Done. Process took %d minutes and %.3f seconds\n",
int($duration/60), ($duration - int($duration/60)*60); # % truncates to integer
}
printf "Filament required: %.1fmm (%.1fcm3)\n",
$sprint->total_used_filament, $sprint->total_extruded_volume/1000;
}
}
} else {
usage(1) unless $opt{save};
}
sub usage {
my ($exit_code) = @_;
my $config = Slic3r::Config->new_from_defaults->as_hash;
my $j = '';
if ($Slic3r::have_threads) {
$j = <<"EOF";
-j, --threads <num> Number of threads to use (1+, default: $config->{threads})
EOF
}
print <<"EOF";
Slic3r $Slic3r::VERSION is a STL-to-GCODE translator for RepRap 3D printers
written by Alessandro Ranellucci <aar\@cpan.org> - http://slic3r.org/
Usage: slic3r.pl [ OPTIONS ] [ file.stl ] [ file2.stl ] ...
--help Output this usage screen and exit
--version Output the version of Slic3r and exit
--save <file> Save configuration to the specified file
--load <file> Load configuration from the specified file. It can be used
more than once to load options from multiple files.
-o, --output <file> File to output gcode to (by default, the file will be saved
into the same directory as the input file using the
--output-filename-format to generate the filename.) If a
directory is specified for this option, the output will
be saved under that directory, and the filename will be
generated by --output-filename-format.
Non-slicing actions (no G-code will be generated):
--repair Repair given STL files and save them as <name>_fixed.obj
--cut <z> Cut given input files at given Z (relative) and export
them as <name>_upper.stl and <name>_lower.stl
--info Output information about the supplied file(s) and exit
$j
GUI options:
--no-plater Disable the plater tab
--gui-mode Overrides the configured mode (simple/expert)
--autosave <file> Automatically export current configuration to the specified file
Output options:
--output-filename-format
Output file name format; all config options enclosed in brackets
will be replaced by their values, as well as [input_filename_base]
and [input_filename] (default: $config->{output_filename_format})
--post-process Generated G-code will be processed with the supplied script;
call this more than once to process through multiple scripts.
--export-svg Export a SVG file containing slices instead of G-code.
-m, --merge If multiple files are supplied, they will be composed into a single
print rather than processed individually.
Printer options:
--nozzle-diameter Diameter of nozzle in mm (default: $config->{nozzle_diameter}->[0])
--print-center Coordinates in mm of the point to center the print around
(default: $config->{print_center}->[0],$config->{print_center}->[1])
--z-offset Additional height in mm to add to vertical coordinates
(+/-, default: $config->{z_offset})
--gcode-flavor The type of G-code to generate (reprap/teacup/makerware/sailfish/mach3/no-extrusion,
default: $config->{gcode_flavor})
--use-relative-e-distances Enable this to get relative E values (default: no)
--use-firmware-retraction Enable firmware-controlled retraction using G10/G11 (default: no)
--gcode-arcs Use G2/G3 commands for native arcs (experimental, not supported
by all firmwares)
--g0 Use G0 commands for retraction (experimental, not supported by all
firmwares)
--gcode-comments Make G-code verbose by adding comments (default: no)
--vibration-limit Limit the frequency of moves on X and Y axes (Hz, set zero to disable;
default: $config->{vibration_limit})
Filament options:
--filament-diameter Diameter in mm of your raw filament (default: $config->{filament_diameter}->[0])
--extrusion-multiplier
Change this to alter the amount of plastic extruded. There should be
very little need to change this value, which is only useful to
compensate for filament packing (default: $config->{extrusion_multiplier}->[0])
--temperature Extrusion temperature in degree Celsius, set 0 to disable (default: $config->{temperature}->[0])
--first-layer-temperature Extrusion temperature for the first layer, in degree Celsius,
set 0 to disable (default: same as --temperature)
--bed-temperature Heated bed temperature in degree Celsius, set 0 to disable (default: $config->{bed_temperature})
--first-layer-bed-temperature Heated bed temperature for the first layer, in degree Celsius,
set 0 to disable (default: same as --bed-temperature)
Speed options:
--travel-speed Speed of non-print moves in mm/s (default: $config->{travel_speed})
--perimeter-speed Speed of print moves for perimeters in mm/s (default: $config->{perimeter_speed})
--small-perimeter-speed
Speed of print moves for small perimeters in mm/s or % over perimeter speed
(default: $config->{small_perimeter_speed})
--external-perimeter-speed
Speed of print moves for the external perimeter in mm/s or % over perimeter speed
(default: $config->{external_perimeter_speed})
--infill-speed Speed of print moves in mm/s (default: $config->{infill_speed})
--solid-infill-speed Speed of print moves for solid surfaces in mm/s or % over infill speed
(default: $config->{solid_infill_speed})
--top-solid-infill-speed Speed of print moves for top surfaces in mm/s or % over solid infill speed
(default: $config->{top_solid_infill_speed})
--support-material-speed
Speed of support material print moves in mm/s (default: $config->{support_material_speed})
--support-material-interface-speed
Speed of support material interface print moves in mm/s or % over support material
speed (default: $config->{support_material_interface_speed})
--bridge-speed Speed of bridge print moves in mm/s (default: $config->{bridge_speed})
--gap-fill-speed Speed of gap fill print moves in mm/s (default: $config->{gap_fill_speed})
--first-layer-speed Speed of print moves for bottom layer, expressed either as an absolute
value or as a percentage over normal speeds (default: $config->{first_layer_speed})
Acceleration options:
--perimeter-acceleration
Overrides firmware's default acceleration for perimeters. (mm/s^2, set zero
to disable; default: $config->{perimeter_acceleration})
--infill-acceleration
Overrides firmware's default acceleration for infill. (mm/s^2, set zero
to disable; default: $config->{infill_acceleration})
--bridge-acceleration
Overrides firmware's default acceleration for bridges. (mm/s^2, set zero
to disable; default: $config->{bridge_acceleration})
--first-layer-acceleration
Overrides firmware's default acceleration for first layer. (mm/s^2, set zero
to disable; default: $config->{first_layer_acceleration})
--default-acceleration
Acceleration will be reset to this value after the specific settings above
have been applied. (mm/s^2, set zero to disable; default: $config->{travel_speed})
Accuracy options:
--layer-height Layer height in mm (default: $config->{layer_height})
--first-layer-height Layer height for first layer (mm or %, default: $config->{first_layer_height})
--infill-every-layers
Infill every N layers (default: $config->{infill_every_layers})
--solid-infill-every-layers
Force a solid layer every N layers (default: $config->{solid_infill_every_layers})
Print options:
--perimeters Number of perimeters/horizontal skins (range: 0+, default: $config->{perimeters})
--top-solid-layers Number of solid layers to do for top surfaces (range: 0+, default: $config->{top_solid_layers})
--bottom-solid-layers Number of solid layers to do for bottom surfaces (range: 0+, default: $config->{bottom_solid_layers})
--solid-layers Shortcut for setting the two options above at once
--fill-density Infill density (range: 0%-100%, default: $config->{fill_density}%)
--fill-angle Infill angle in degrees (range: 0-90, default: $config->{fill_angle})
--fill-pattern Pattern to use to fill non-solid layers (default: $config->{fill_pattern})
--solid-fill-pattern Pattern to use to fill solid layers (default: $config->{solid_fill_pattern})
--start-gcode Load initial G-code from the supplied file. This will overwrite
the default command (home all axes [G28]).
--end-gcode Load final G-code from the supplied file. This will overwrite
the default commands (turn off temperature [M104 S0],
home X axis [G28 X], disable motors [M84]).
--layer-gcode Load layer-change G-code from the supplied file (default: nothing).
--toolchange-gcode Load tool-change G-code from the supplied file (default: nothing).
--seam-position Position of loop starting points (random/nearest/aligned, default: $config->{seam_position}).
--external-perimeters-first Reverse perimeter order. (default: no)
--spiral-vase Experimental option to raise Z gradually when printing single-walled vases
(default: no)
--only-retract-when-crossing-perimeters
Disable retraction when travelling between infill paths inside the same island.
(default: no)
--solid-infill-below-area
Force solid infill when a region has a smaller area than this threshold
(mm^2, default: $config->{solid_infill_below_area})
--infill-only-where-needed
Only infill under ceilings (default: no)
--infill-first Make infill before perimeters (default: no)
Quality options (slower slicing):
--extra-perimeters Add more perimeters when needed (default: yes)
--avoid-crossing-perimeters Optimize travel moves so that no perimeters are crossed (default: no)
--thin-walls Detect single-width walls (default: yes)
--overhangs Experimental option to use bridge flow, speed and fan for overhangs
(default: yes)
Support material options:
--support-material Generate support material for overhangs
--support-material-threshold
Overhang threshold angle (range: 0-90, set 0 for automatic detection,
default: $config->{support_material_threshold})
--support-material-pattern
Pattern to use for support material (default: $config->{support_material_pattern})
--support-material-spacing
Spacing between pattern lines (mm, default: $config->{support_material_spacing})
--support-material-angle
Support material angle in degrees (range: 0-90, default: $config->{support_material_angle})
--support-material-interface-layers
Number of perpendicular layers between support material and object (0+, default: $config->{support_material_interface_layers})
--support-material-interface-spacing
Spacing between interface pattern lines (mm, set 0 to get a solid layer, default: $config->{support_material_interface_spacing})
--raft-layers Number of layers to raise the printed objects by (range: 0+, default: $config->{raft_layers})
--support-material-enforce-layers
Enforce support material on the specified number of layers from bottom,
regardless of --support-material and threshold (0+, default: $config->{support_material_enforce_layers})
--dont-support-bridges
Experimental option for preventing support material from being generated under bridged areas (default: yes)
Retraction options:
--retract-length Length of retraction in mm when pausing extrusion (default: $config->{retract_length}[0])
--retract-speed Speed for retraction in mm/s (default: $config->{retract_speed}[0])
--retract-restart-extra
Additional amount of filament in mm to push after
compensating retraction (default: $config->{retract_restart_extra}[0])
--retract-before-travel
Only retract before travel moves of this length in mm (default: $config->{retract_before_travel}[0])
--retract-lift Lift Z by the given distance in mm when retracting (default: $config->{retract_lift}[0])
--retract-layer-change
Enforce a retraction before each Z move (default: yes)
--wipe Wipe the nozzle while doing a retraction (default: no)
Retraction options for multi-extruder setups:
--retract-length-toolchange
Length of retraction in mm when disabling tool (default: $config->{retract_length}[0])
--retract-restart-extra-toolchnage
Additional amount of filament in mm to push after
switching tool (default: $config->{retract_restart_extra}[0])
Cooling options:
--cooling Enable fan and cooling control
--min-fan-speed Minimum fan speed (default: $config->{min_fan_speed}%)
--max-fan-speed Maximum fan speed (default: $config->{max_fan_speed}%)
--bridge-fan-speed Fan speed to use when bridging (default: $config->{bridge_fan_speed}%)
--fan-below-layer-time Enable fan if layer print time is below this approximate number
of seconds (default: $config->{fan_below_layer_time})
--slowdown-below-layer-time Slow down if layer print time is below this approximate number
of seconds (default: $config->{slowdown_below_layer_time})
--min-print-speed Minimum print speed (mm/s, default: $config->{min_print_speed})
--disable-fan-first-layers Disable fan for the first N layers (default: $config->{disable_fan_first_layers})
--fan-always-on Keep fan always on at min fan speed, even for layers that don't need
cooling
Skirt options:
--skirts Number of skirts to draw (0+, default: $config->{skirts})
--skirt-distance Distance in mm between innermost skirt and object
(default: $config->{skirt_distance})
--skirt-height Height of skirts to draw (expressed in layers, 0+, default: $config->{skirt_height})
--min-skirt-length Generate no less than the number of loops required to consume this length
of filament on the first layer, for each extruder (mm, 0+, default: $config->{min_skirt_length})
--brim-width Width of the brim that will get added to each object to help adhesion
(mm, default: $config->{brim_width})
Transform options:
--scale Factor for scaling input object (default: 1)
--rotate Rotation angle in degrees (0-360, default: 0)
--duplicate Number of items with auto-arrange (1+, default: 1)
--bed-size Bed size, only used for auto-arrange (mm, default: $config->{bed_size}->[0],$config->{bed_size}->[1])
--duplicate-grid Number of items with grid arrangement (default: 1,1)
--duplicate-distance Distance in mm between copies (default: $config->{duplicate_distance})
Sequential printing options:
--complete-objects When printing multiple objects and/or copies, complete each one before
starting the next one; watch out for extruder collisions (default: no)
--extruder-clearance-radius Radius in mm above which extruder won't collide with anything
(default: $config->{extruder_clearance_radius})
--extruder-clearance-height Maximum vertical extruder depth; i.e. vertical distance from
extruder tip and carriage bottom (default: $config->{extruder_clearance_height})
Miscellaneous options:
--notes Notes to be added as comments to the output file
--resolution Minimum detail resolution (mm, set zero for full resolution, default: $config->{resolution})
Flow options (advanced):
--extrusion-width Set extrusion width manually; it accepts either an absolute value in mm
(like 0.65) or a percentage over layer height (like 200%)
--first-layer-extrusion-width
Set a different extrusion width for first layer
--perimeter-extrusion-width
Set a different extrusion width for perimeters
--infill-extrusion-width
Set a different extrusion width for infill
--solid-infill-extrusion-width
Set a different extrusion width for solid infill
--top-infill-extrusion-width
Set a different extrusion width for top infill
--support-material-extrusion-width
Set a different extrusion width for support material
--bridge-flow-ratio Multiplier for extrusion when bridging (> 0, default: $config->{bridge_flow_ratio})
Multiple extruder options:
--extruder-offset Offset of each extruder, if firmware doesn't handle the displacement
(can be specified multiple times, default: 0x0)
--perimeter-extruder
Extruder to use for perimeters (1+, default: $config->{perimeter_extruder})
--infill-extruder Extruder to use for infill (1+, default: $config->{infill_extruder})
--support-material-extruder
Extruder to use for support material (1+, default: $config->{support_material_extruder})
--support-material-interface-extruder
Extruder to use for support material interface (1+, default: $config->{support_material_interface_extruder})
--ooze-prevention Drop temperature and park extruders outside a full skirt for automatic wiping
(default: no)
--standby-temperature-delta
Temperature difference to be applied when an extruder is not active and
--ooze-prevention is enabled (default: $config->{standby_temperature_delta})
EOF
exit ($exit_code || 0);
}
__END__
|