1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
|
U-Boot for UniPhier SoC family
==============================
Recommended toolchains
----------------------
The UniPhir platform is well tested with Linaro toolchanis.
You can download pre-built toolchains from:
http://www.linaro.org/downloads/
Compile the source
------------------
sLD3 reference board:
$ make uniphier_sld3_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabihf-
LD4 reference board:
$ make uniphier_ld4_sld8_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabihf-
sLD8 reference board:
$ make uniphier_ld4_sld8_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-sld8-ref
Pro4 reference board:
$ make uniphier_pro4_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabihf-
Pro4 Ace board:
$ make uniphier_pro4_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pro4-ace
Pro4 Sanji board:
$ make uniphier_pro4_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pro4-sanji
Pro5 4KBOX Board:
$ make uniphier_pxs2_ld6b_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pro5-4kbox
PXs2 Gentil board:
$ make uniphier_pxs2_ld6b_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pxs2-gentil
PXs2 Vodka board:
$ make uniphier_pxs2_ld6b_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabihf-
LD6b reference board:
$ make uniphier_pxs2_ld6b_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-ld6b-ref
LD11 reference board:
$ make uniphier_ld11_defconfig
$ make CROSS_COMPILE=aarch64-linux-gnu-
LD20 reference board:
$ make uniphier_ld20_defconfig
$ make CROSS_COMPILE=aarch64-linux-gnu-
You may wish to change the "CROSS_COMPILE=..." to use your favorite compiler.
Burn U-Boot images to NAND
--------------------------
Write the following to the NAND device:
- spl/u-boot-spl.bin at the offset address 0x00000000
- u-boot.bin at the offset address 0x00010000
or
- u-boot-with-spl.bin at the offset address 0x00000000
If a TFTP server is available, the images can be easily updated.
Just copy the u-boot-spl.bin and u-boot.bin to the TFTP public directory,
and then run the following command at the U-Boot command line:
=> run nandupdate
Burn U-Boot images to eMMC
--------------------------
Write the following to the Boot partition 1 of the eMMC device:
- spl/u-boot-spl.bin at the offset address 0x00000000
- u-boot.bin at the offset address 0x00010000
or
- u-boot-with-spl.bin at the offset address 0x00000000
If a TFTP server is available, the images can be easily updated.
Just copy the u-boot-spl.bin and u-boot.bin to the TFTP public directory,
and then run the following command at the U-Boot command line:
=> run emmcupdate
UniPhier specific commands
--------------------------
- pinmon (enabled by CONFIG_CMD_PINMON)
shows the boot mode pins that has been latched at the power-on reset
- ddrphy (enabled by CONFIG_CMD_DDRPHY_DUMP)
shows the DDR PHY parameters set by the PHY training
- ddrmphy (enabled by CONFIG_CMD_DDRMPHY_DUMP)
shows the DDR Multi PHY parameters set by the PHY training
Supported devices
-----------------
- UART (on-chip)
- NAND
- SD/eMMC
- USB 2.0 (EHCI)
- USB 3.0 (xHCI)
- GPIO
- LAN (on-board SMSC9118)
- I2C
- EEPROM (connected to the on-board I2C bus)
- Support card (SRAM, NOR flash, some peripherals)
Micro Support Card
------------------
The recommended bit switch settings are as follows:
SW2 OFF(1)/ON(0) Description
------------------------------------------
bit 1 <---- BKSZ[0]
bit 2 ----> BKSZ[1]
bit 3 <---- SoC Bus Width 16/32
bit 4 <---- SERIAL_SEL[0]
bit 5 ----> SERIAL_SEL[1]
bit 6 ----> BOOTSWAP_EN
bit 7 <---- CS1/CS5
bit 8 <---- SOC_SERIAL_DISABLE
SW8 OFF(1)/ON(0) Description
------------------------------------------
bit 1 <---- CS1_SPLIT
bit 2 <---- CASE9_ON
bit 3 <---- CASE10_ON
bit 4 Don't Care Reserve
bit 5 Don't Care Reserve
bit 6 Don't Care Reserve
bit 7 ----> BURST_EN
bit 8 ----> FLASHBUS32_16
The BKSZ[1:0] specifies the address range of memory slot and peripherals
as follows:
BKSZ Description RAM slot Peripherals
--------------------------------------------------------------------
0b00 15MB RAM / 1MB Peri 00000000-00efffff 00f00000-00ffffff
0b01 31MB RAM / 1MB Peri 00000000-01efffff 01f00000-01ffffff
0b10 64MB RAM / 1MB Peri 00000000-03efffff 03f00000-03ffffff
0b11 127MB RAM / 1MB Peri 00000000-07efffff 07f00000-07ffffff
Set BSKZ[1:0] to 0b01 for U-Boot.
This mode is the most handy because EA[24] is always supported by the save pin
mode of the system bus. On the other hand, EA[25] is not supported for some
newer SoCs. Even if it is, EA[25] is not connected on most of the boards.
--
Masahiro Yamada <yamada.masahiro@socionext.com>
Oct. 2016
|
