1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
|
/*
* (C) Copyright 2001
* Bill Hunter, Wave 7 Optics, williamhunter@mediaone.net
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* On Semiconductor's LM75 Temperature Sensor
*/
#include <common.h>
#include <i2c.h>
#include <dtt.h>
/*
* Device code
*/
#if defined(CONFIG_SYS_I2C_DTT_ADDR)
#define DTT_I2C_DEV_CODE CONFIG_SYS_I2C_DTT_ADDR
#else
#define DTT_I2C_DEV_CODE 0x48 /* ON Semi's LM75 device */
#endif
#define DTT_READ_TEMP 0x0
#define DTT_CONFIG 0x1
#define DTT_TEMP_HYST 0x2
#define DTT_TEMP_SET 0x3
int dtt_read(int sensor, int reg)
{
int dlen;
uchar data[2];
#ifdef CONFIG_DTT_AD7414
/*
* On AD7414 the first value upon bootup is not read correctly.
* This is most likely because of the 800ms update time of the
* temp register in normal update mode. To get current values
* each time we issue the "dtt" command including upon powerup
* we switch into one-short mode.
*
* Issue one-shot mode command
*/
dtt_write(sensor, DTT_CONFIG, 0x64);
#endif
/* Validate 'reg' param */
if((reg < 0) || (reg > 3))
return -1;
/* Calculate sensor address and register. */
sensor = DTT_I2C_DEV_CODE + (sensor & 0x07);
/* Prepare to handle 2 byte result. */
if ((reg == DTT_READ_TEMP) ||
(reg == DTT_TEMP_HYST) ||
(reg == DTT_TEMP_SET))
dlen = 2;
else
dlen = 1;
/* Now try to read the register. */
if (i2c_read(sensor, reg, 1, data, dlen) != 0)
return -1;
/* Handle 2 byte result. */
if (dlen == 2)
return ((int)((short)data[1] + (((short)data[0]) << 8)));
return (int)data[0];
} /* dtt_read() */
int dtt_write(int sensor, int reg, int val)
{
int dlen;
uchar data[2];
/* Validate 'reg' param */
if ((reg < 0) || (reg > 3))
return 1;
/* Calculate sensor address and register. */
sensor = DTT_I2C_DEV_CODE + (sensor & 0x07);
/* Handle 2 byte values. */
if ((reg == DTT_READ_TEMP) ||
(reg == DTT_TEMP_HYST) ||
(reg == DTT_TEMP_SET)) {
dlen = 2;
data[0] = (char)((val >> 8) & 0xff); /* MSB first */
data[1] = (char)(val & 0xff);
} else {
dlen = 1;
data[0] = (char)(val & 0xff);
}
/* Write value to register. */
if (i2c_write(sensor, reg, 1, data, dlen) != 0)
return 1;
return 0;
} /* dtt_write() */
int dtt_init_one(int sensor)
{
int val;
/* Setup TSET ( trip point ) register */
val = ((CONFIG_SYS_DTT_MAX_TEMP * 2) << 7) & 0xff80; /* trip */
if (dtt_write(sensor, DTT_TEMP_SET, val) != 0)
return 1;
/* Setup THYST ( untrip point ) register - Hysteresis */
val = (((CONFIG_SYS_DTT_MAX_TEMP - CONFIG_SYS_DTT_HYSTERESIS) * 2) << 7) & 0xff80;
if (dtt_write(sensor, DTT_TEMP_HYST, val) != 0)
return 1;
/* Setup configuraton register */
#ifdef CONFIG_DTT_AD7414
/* config = alert active low and disabled */
val = 0x60;
#else
/* config = 6 sample integration, int mode, active low, and enable */
val = 0x18;
#endif
if (dtt_write(sensor, DTT_CONFIG, val) != 0)
return 1;
return 0;
} /* dtt_init_one() */
int dtt_get_temp(int sensor)
{
int const ret = dtt_read(sensor, DTT_READ_TEMP);
if (ret < 0) {
printf("DTT temperature read failed.\n");
return 0;
}
return (int)((int16_t) ret / 256);
} /* dtt_get_temp() */
|
