1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
|
# ============================================================================
# WAN Router Configuration File.
# ============================================================================
# Protocol: Cisco HDLC (CHDLC): PRIMARY Port Configuration
# ----------------------------------------------------------------------------
#*****************************************
# Device Definition Section *
#*****************************************
#
# The [devices] section defines physical WAN connections. Each
# statement in this section has the following format:
#
# Usage: {device} = {protocol}, Comment
#
# {device} : WAN device name; First card in the system
# must be named "wanpipe1".
#
# {protocol} : WAN protocol currently supported:
# WAN_X25 generic X.25 configuration
# WAN_PPP generic PPP configuration
# WAN_FR generic frame relay configuration
# WAN_CHDLC generic Cisco HDLC configuration
#
[devices]
wanpipe1 = WAN_CHDLC, Cisco HDLC
#****************************************
# Network Interfaces Definitions *
#****************************************
#
# The [interfaces] section defines logical channels and corresponding
# network interfaces created by the router. Each statement in this section
# has the following format:
#
# {interface name} = {device}, {media_addr}, {function}, Comment
#
# Where: {interface name} : Interface name must be the same
# as interface file name defined in
# /usr/lib/wanrouter/interface.
#
# {device} : Defined above in [devices] section
#
# {media_addr} : Not used, leave blank
#
# {function} : Options: WANPIPE or API
# WANPIPE: used for routing chdlc packets.
# API: used for raw socket interface to the
# board.
#
# NOTE: CHDLC uses two ports PRI (primary high speed) and
# SEC (secondary low speed)
# Each port is treated as a separate device, thus on one physical card,
# we can have two wanpipe devices defined for each port !!
#
# NOTE: It is recomended that the PRIMARY port be used first. The
# second port is optional !!!
[interfaces]
wp1_chdlc = wanpipe1, ,WANPIPE, PRI port connection (high speed 2Mbps)
#********************************************
# Link configuration section *
#********************************************
#
# Each statement of the configuration section has the following format:
#
# parameter=value
#
# where:
# parameter symbolic name of the configuration parameter.
# value number or symbolic name representing value of the
# configuration parameter.
#
# NOTE: A link configuration section must be specified for each device
# defined in [device] section. The name must also be the same as
# declared above in [devices]
#
# For s508 Card:
# Set the IOPort and IRQ options and
# comment out the S514CPU and PCISlot options.
# For S514 PCI Card:
# Set the S514CPU and PCISlot options and
# comment out the IOPort and IRQ options
#
# Using PRI and SEC port on one card:
# For S508 Card:
# For both wanpipe1 and wanpipe2 definitions, IOport and IRQ
# must have the same values.
# For S514 Card:
# For both wanpipe1 and wanpipe2 definitions, S514CPU and
# PCISlot must have the same values.
#
# This is know as 'piggybacking', since SEC port uses the resources
# of the PRI port.
#
#------------------------ WANPIPE 1 -------------------------------------
[wanpipe1]
# ----- Hardware configuration ---------------
#S514CPU = A # S514 PCI Card CPU: A or B (s514 only)
#PCISlot = 0 # PCI Slot num: 0 for autodetect (s514 only)
#
IOPort = 0x360 # I/O port base (s508 only)
IRQ = 7 # interrupt request level (s508 only)
#
CommPort = PRI # PRI: High speed (2 MBps) primary port
# SEC: Low speed (512 MBps) secondary port
#
Firmware = /usr/lib/wanpipe/cdual514.sfm # adapter firmware
#
# ----- Dual Port Memory Base Address --------
#Memaddr = 0xD0000 # Commenting this out enables Auto Memory
# selection. Valid Memory addresses are:
# 0xA0000,0xA2000...0xAE000 / 0xC0000,0xC2000...
# 0xCE000 / 0xD0000,0xD2000...0xDE000 / 0xE0000,
# 0xE2000...0xEE000
#
# ----- Physical interface configuration -----
Interface = V35 # physical interface type, RS232/V35
Clocking = External # Tx/Rx clock source, External/Internal
#
# * Jumpers must be set for internal or external
# clocking for:
# s508 : RS232 SEC port
# s514 : RS232 PRI and SEC port
#
#
BaudRate = 1540000 # data transfer rate in bps, 1200..2048000
# Note: Max 256KBps for RS232 interface !!!
#
# ----- Media-specific configuration ---------
MTU = 1500 # maximum data transfer unit, bytes
TTL = 0x7F # Time To Live parameter for UDP packets
UDPPORT = 9000 # UDP Port, used by cpipemon debugger
#*************************************************************
# Logical channel (interface) configuration sections. *
#*************************************************************
#
# Each statement of the configuration section has the following format:
#
# parameter=value
#
# where:
# parameter symbolic name of the configuration parameter
# value number or symbolic name representing value of the
# configuration parameter.
#
# Interface name must be the same as the interface file
# name defined in /usr/lib/wanrouter/interfaces !
#
# Recomended nameing convention: (wp#_chldc)
# where wp# represents wanpipe1,2,3 ...
#
# A Logical section must be defined for each interface name
# defined in [interfaces] section.
#
# To turn OFF Dynamic IP addressing set SLARP_TIMER to 0.
[wp1_chdlc]
# --------- Link Management parameters ---------
MULTICAST = NO # Enable Multicasting
#
IGNORE_DCD = NO # Ignore DCD when determining active link status
# (YES/NO) Default: NO (ONLY USED FOR TESTING)
#
IGNORE_CTS = NO # Ignore CTS when determining active link status
# (YES/NO) Default: NO (ONLY USED FOR TESTING)
#
IGNORE_KEEPALIVE= NO # Ignore Keep alives when determining active
# link status (YES/NO) Default: NO
# (ONLY USED FOR TESTING)
#
HDLC_STREAMING = NO # Options YES or NO
# YES: Turns OFF cisco hdlc protocol
# and uses raw frames, and no polling.
# NO: Turns ON the cisco hdlc protocol
#
KEEPALIVE_TX_TIMER = 10000 # Interval between Keep Alive (0-60000 ms)
# Default 10000ms
#
KEEPALIVE_RX_TIMER = 11000 # Interval to expect Keepalives (10-60000 ms)
# Default 10000ms
#
KEEPALIVE_ERR_MARGIN = 5 # Consecutive keepalive timeouts before bringing
# down the link. Default 3, range: 1 - 20
#
SLARP_TIMER = 0 # Used for DYNAMIC/STATIC IP addressing
#
# 0 : Static IP addressing.
# IP addresses are obtained from
# the interface file:
# (usr/lib/wanrouter/interfaces/wp1_chdlc)
#
# Non Zero : Dynamic IP addressing.
# IP addresses are requested from
# the remote station.
# Valid values are from 1-6000(ms)
# Default: 5000
# Note: A dummy interface file
# is still required !!!
#--------------------- END OF WANPIPE CONFIGURATION ------------------------
|
