=== For New Users

Many of  the special features of _WSJT-X Improved_ are accessed via the *File | Settings | General*
menu. Where screenshots of this are presented, only the relevant items are shown. In other cases, the
screenshots will show the tab and item, or the setting will be referred to explicitly, as above.

If you have used the default installer, the windows will resemble the standard _WSJT-X_ layout. Two differences
may be seen: Band Buttons and vertical lines on the Wide Graph.  The Band Buttons  can be removed or restored 
using the check box in the *View* menu, and the vertical lines are controlled by the *Bars* checkbox on the
Wide Graph. 


=== Wait Features

Three *Wait* features are available: *Wait and Reply*, *Wait and Call* and *Wait and Pounce*.
The *Wait* features are enabled using the checkbox in the *File | Settings | General* menu:

image::wait1.png[align="center",alt="wait1"]

When selected, both the *DX Call* field and *Enable Tx* button will turn yellow, to warn you that
an automatic transmission could occur. 

.Wait and Reply

If a callsign is present in the *DX Call* field, *Wait and Reply* will attempt to continue your QSO when
that station sends you a message. For example, you may have called a station, receive no reply and stop
transmitting if the station has replied to someone else. If the station then calls you, your QSO will
resume automatically.  This feature  also ensures that a second RR73 is sent by you in case your first one
is not answered. 

IMPORTANT: Your rig may be set to Tx when *Wait and Reply* is enabled. Take the necessary precautions!

TIP: *Wait and Reply* is enabled for all modes where Auto Seq is available, as long as you have the callsign 
of the other station present in the *DX Call* field.

NOTE: You should not have a callsign present in the *DX Call* field longer than necessary for the QSO 
unless you wish to monitor the station.  It is good practice to clear the *DX Call* field after a QSO, 
for example by right clicking on the *DX Call* button.

.Wait and Call

*Wait and Call* is useful if the station you are trying to work disappears for a time, for example in QSB.
To enable the feature, click on the *DX Call* button, which will then turn red (if a callsign is present in
the *DX Call* field). If that station is subsequently decoded sending a message containing CQ, RR73, RRR or 73,
up to three calls to that station will be made automatically. Any manual intervention, such as pressing the 
*Halt Tx* or *Stop* buttons, will immediately disable *Wait and Call* giving you full control
over the QSO.

IMPORTANT: Your rig may be set to Tx when *Wait and Call* is enabled. Take the necessary precautions!

.Wait and Pounce

*Wait and Pounce* can be used to answer a CQ call from another station, with specific criteria. 
To activate *Wait and Pounce*, ensure that the *DX Call* box is empty, then 
select one of the applicable CQ: categories from the control on main window  (i.e. CQ: Max Dist
 or CQ: Max dB or CQ: Min dB) and then right-click on the *Enable Tx* button, which then turns orange
(with black lettering). In the next period, a reply will be sent automatically, to either the most
distant / strongest / weakest CQ station.

image::cqtype.png[align="center",alt="cqtype"]

Wait and Pounce can also be combined with the *Filters* feature. You can then for example “wait” for CQ messages
containing a certain prefix, grid, callsign or keyword.

TIP: When using CQ: Max Dist, CQ: Max dB, and CQ: Min dB, the program automatically prevents working dupes. The data for this comes from the file "wsjtx.log". Stations from this file are ignored by Wait & Pounce, and when you are calling CQ yourself. To reset everything, click in the *File* menu on *Erase wsjtx.log*.  Attention: Do not accidentally erase the file “wsjtx_log.adi” as it contains your logbook.

IMPORTANT: Your rig may be set to Tx when *Wait and Pounce* is enabled. Take the necessary precautions!

=== Filters

The *Filters* give you a powerful tool for customization of what is being displayed in the Band Activity
window. The primary *Filters* settings form is accessed from *File | Settings | Filters* and is shown below.

image::filters1.png[align="center",alt="Filters"]

You can specify up to four territories for which hiding messages can be switched on or off using
the options available in the *Filter* tab on the main window. From this tab you can also hide messages from a
specific continent, or stations worked before on a band.

The form  contains a "Blacklist", a "Whitelist", and an "Always Pass list". These lists can
be operated in combination, if desired.

.Blacklist

The Blacklist can for example be used to hide pirate stations, contest messages or messages with unwanted 
content. You can enter whole callsigns, parts of them or keywords.

.Whitelist

A meaningful use of the Whitelist is if you are ONLY interested in messages with certain grids, calls, or
keywords. All other messages, except those allowed via the Always Pass list, will then be hidden.

.Always Pass List

Use the Always pass list to display specific stations even though the respective country or continent is hidden.

You can optionally apply the filters only to the callsigns of the calling stations, or use the filters for *Wait and 
Pounce* only. In the latter case, all messages will be displayed in the Band Activity window, but *Wait and Pounce*
will respond only to stations that meet the set filter criteria. 

As soon as a filter is activated that results in not all decodes being displayed in the Band Activity window, this 
is indicated in the status label(this is the display at the bottom left of the main wondow).  It changes from green
"Receiving" to cyan "Receiving, Filters on".

TIP: Filters are automatically disabled for Special Operating modes, so that you don’t accidentally miss a station.

Additional filter options available directly via the main program window. All these so-called Quick Filters are now
combined in a separate Filters menu, which can be viewed using the *Filters* tab on the main window:

image::filters2.png[align="center",alt="Quick Filters"]

An additional option allows the three respective Hide/Ignore/Highlight Quick Filters to be switchable between “worked today”
and “worked today or yesterday”. There is now a third checkbox for this in Settings/Filters. The text displayed in the main program
under Filters switches accordingly. The new additional option is shown below.

image::filters3.png[align="center",alt="Quick Filters 2"]

A checkbox (labelled *BP*) on the main window allows all set filter options to be bypassed temporarily with a single
click. This can be used, for example, if you have hidden certain areas (e.g. to display only DX stations) but now
want to monitor the entire band activity for a certain time.

.Ignore List

A click on the *Ignore* button (located on the main window below the *DX Grid* box) adds the callsign present 
in the *DX Call* box to a so-called "Ignore list". If you have also activated the "Ignore stations from the Ignore List"
checkbox (located in the *Filters* tab on the main window), such stations are automatically ignored when you use
*CQ: First*, *CQ: Max Dist*, *CQ: Max dB*, *CQ: Min dB* or *Wait and Reply*. 

The "Ignore List" will be created in your log directory the first time a station is added to it.
You can erase the "Ignore List" from the *File* tab on the main window.

TIP: For callsigns from the “Ignore list”, or from the three "Ignore ..." Quick Filters no alert sounds are played
unless you have activated the *BP* (bypass) checkbox. This can be used to temporarily mute the alerts for a certain callsign.

=== GUI Indicators/Buttons

Several GUI indicators/buttons change colour to indicate that certain features have been enabled, or can 
have their function modified.  These are listed below:

.DX Call Button

If *Wait* features have been selected and there is a callsign in the *DX Call* box, then the *DX Call* button turns yellow to warn that your station is 'primed' to transmit.

.Enable Tx

If *Wait and Pounce* has been set, *Enable Tx* turns orange (with black lettering).

.Monitor

The *Monitor* button turns cyan if audio file saving has been selected from the *Save* tab.

.Erase Button

Alternate Erase button behaviour can be enabled using the checkbox in the "Additional features* group in
the *File | Settings* page. 

- Left-click --> Erase the Band Activity window

- Right-click --> Erase the Rx Frequency window 

- Double-click on left mouse button --> Erase both windows (unchanged)

.kHz entry without 'k'

EME operation in particular has activity spread out over a range of frequencies within band. Tuning to a new frequency 
can be accomplished by typing the new frequency into the *Band Combo* box located to the left of the Dial Frequency* 
indicator. Normally to move a certain number of kHz above band edge you need to type a 'k' sfter the number.  For example,
if operating on 10368MHz, to move to 10368.123 type 123k followed by the Enter key.  A common mistake during operation is
to forget the k, in which case you usually experience a rig oontrol error!

By selecting the checkbox in *File | Settings* Behavior group, the requirement to enter the 'k' is no longer needed
(after closing and restarting the program).

.Control of rig frequency by mouse

Mouse buttons (left and right) and the scroll wheel can be used to adjust the dial frequency in 1Khz increments.
These tuning options are available when the mouse pointer is placed over the Dial Frequency indicator.

=== Advanced highlighting options

An alternative color scheme is available via the *|Colors|* tab.  Some users find this  easier on the eyes and  is more
suitable for the dark  style due to its more pastel-like colours.  Buttons are provided to allow the user to select
either the original _WSJT-X_  or the alternative styles.  With the alternative style, stations uploading their logbook
to _LotW_ will have black foreground color, others red. Stations worked before are displayed with grey background.

image::highlighting.png[align="center",alt="Decode Highlighting"]

It is still possible for you to customise the color scheme according to your own preferences.

In addition, you can  highlight individual callsigns or grids according to your specifications. 
Callsigns and/or grids can be highlighted with orange or blue background color. Callsigns/grids must be separated
by commas and can be mixed (e.g. "K1JT, DG2YCB, JO33, JN58,"). 

IMPORTANT: There must be a comma after each callsign, and also at the end of the line.

=== Three Different GUIs

_Wsjt-x_improved_ is  available with three different GUIs.  For technical reasons, each version uses a different intaller.

The default download  has  the standard _WSJT-X_ GUI. The second is  more compact  (= alternative layout, "AL"),and the third
is optimized for widescreens. The latter two provide a larger Band Activity window, so that you don't need to scroll that often.
Just try them and see which you like best.

Screen shot of the version with the *alternative layout* (AL):

image::algui.png[align="center",alt="algui"]

Screen shot of the *widescreen* version:

image::widegui.png[align="center",alt="widegui"]

You can also install several program versions side by side by installing them in separate directories 
(eg "c:\WSJT\wsjtx_improved", "c:\WSJT\wsjtx_improved_AL", "c:\WSJT\wsjtx_improved_widesreen)"), and by creating
starter hyperlinks on your desktop for the "wsjtx.exe" files located in the respective \bin subfolders. 
Then you can start them as required and make a good comparison. Your WSJT-X.ini file with your settings will be recognized
and used automatically.

In Windows, the starter hyperlinks can be located in a suitably named  "batch" file. The batch file is created
by starting a new text file (for convenience on your desktop) with the following example text:

c:\WSJT\wsjtx_improved\bin

start  wsjtx 

After saving the file, rename it with extension .bat.  Double clicking the batch file will then run WSJT-X from
the specified directory.

If you want to run several program instances at the same time, this is also possible using the "rig-name"
method, as desribed elsewhere in the this User Guide.  A suitable batch file for this would be:

c:\WSJT\wsjtx_improved_AL\bin

start  wsjtx --rig-name=NAME_XYZ

The program then creates individual .ini files for each instance so that they can be operated independently of each other.

=== Dark Style

You can switch easily to dark style directly in the main window. Just click on the new item *"Use Dark Style"* 
in the *|View|* menu.  This switch adjusts some internal settings and uses an optimized stylesheet for the dark style.
If you have enabled the dark style, you should adjust the highlight color scheme towards pastel tones via
*File | Settings | Colors|* and adjust the background colors according to your preferences.

image::dark.png[align="center",alt="Dark Style"]

=== Optional Band Buttons

Optional band select buttons can be switched on or off in the View menu.  A click on one of the band select buttons takes
you to your preferred band/mode default frequency, and a right-click sets the main DXpedition frequencies.

image::bandbutton1.png[align="center",alt="bandbutton1"]

Band select buttons are available for all 3 GUI layouts. This is how it looks with the AL version:

image::bandbutton2.png[align="center",alt="bandbutton2"]

=== Extra Features for the Widegraph window

.Optional display of bars for Rx and Tx frequency on the waterfall 

image::wgfeatures1.png[align="center",alt="wgfeatures1"]

.Additional options for the Time stamp on the waterfall: Off / Left / Right

image::wgfeatures2.png[align="center",alt="wgfeatures2"]

.Improved behavior of the mouse buttons when clicking on the waterfall display

- Left-click --> set Rx offset (unchanged)
- Right-click --> set Tx offset (NEW feature)
- Double-click on right mouse button --> set Rx & Tx offset (Rx = Tx), (NEW feature)
- Shift + left-click --> set Tx offset (unchanged) 
- Ctrl + left-click --> set Rx & Tx offset (unchanged)

=== Diagnostic Mode

_Wsjt-x_improved_ has a built-in diagnostic mode, available from the *Save* menu tab.
This makes it easy to collect data to troubleshoot problems with the program, or with its communication with your rig
(hamlib issues, not responding COM ports, etc.).

image::diagnostic.png[align="center",alt="Diagnostic mode"]

=== Audio Alerts

Use of this feature requires that your system is equipped with two sound cards. This requirement is fulfilled when 
your rig is connected via USB audio (FT-991, IC-7100, etc), or if your computer itelf has an additional soundcard. 
The audio alerts will be played on the *default audio device* (for example the loudspeaker of your computer),
while the normal _WSJT-X_ output is still fed to your rig only. 

The first step  is to set up the computer's audio devices appropriately.
The figure below shows the settings for a Windows 10 computer,  where the internal sound card provides audio via
an analogue cable to the radio, and an external USB dongle has been added to play the audio alerts.  The menu was obtained
by right clicking on the loudspeaker tray icon, selecting 'Sounds' and then the 'Playback' tab.

image::audiostep1.png[align="center", alt="audiostep1"]

The second step is to ensure that your radio receives transmit audio from the correct device.  This is shown below for
the same computer.

image::audiostep2.png[align="center", alt="audiostep2"]


IMPORTANT: Ensure that your rig is NOT connected via "Default Device", else your audio alerts could be tranmitted
over the air!

You can check that the audio alerts are being directed to the correct device by right-clicking once on the *Band Hopping*
button in Tab 3, as shown below. A test message will then be played.

image::testalerts.png[align="center",alt="testalerts"]

Audio alerts can be set up via the *Alerts* tab on *File | Settings* by selecting the checkboxes according
to your preferences, and then clicking on *Enable Audio Alerts*, which will turn green to indicate that audio alerts
are active. The available  audio alert settings are shown below:

image::alerts.png[align="center",alt="Alerts"]

The four alerts below the line do not require any further settings to be made to play the sounds.  
The checkboxes *Highlight DX Call in message* and *Highlight DX Grid in message* in *File | Settings | General* 
"Display" group can be used to identify what triggered the "DX" alert. 

The ten alert categories above the line require the checkbox *Show DXCC, grid and worked before status* in 
*File | Settings | General*  "Display" group to be selected.  To identify what triggered these alerts, 
ensure that the relevant categories in *File | Settings | Colors* are selected.

TIP: As for callsigns from the "Ignore list", or from the three "Ignore ..." Quick Filters,  no alert sounds are played
unless you have checked the *BP* (bypass) checkbox,this can be used to mute the alerts for a certain callsign 
with one click on the *Ignore* button. To reset everything and unmute the alert, click in the *File* menu on *Erase Ignore List*, or uncheck the "Ignore ..." Quick Filters.

=== Show distance/azimuth with grid

If a station sends a valid Maidenhead locator, _WSJT-X -improved_ now automatically calculates the distance and the great-circle azimuth
and displays it in the Band Activity pane.  The calculations are made from your grid locator to the centre of the 4 character 
DX grid locator, with a consequent limitation on accuracy.  

TIP: The Band Activity pane requires sufficient width to display the results.

A new "Align DXCC / distance / azimuth" checkbox allows you to keep the DXCC names (or principal prefixes) 
as well as distance/azimuth in an aligned table form. Two spin boxes allow further configuration of the preferred layout:

- The first spin box sets the number of spaces between the decoded message and the DXCC name (or the principal prefix). 
The default is set to "1", which means one  space more compared to the WSJT-X standard.

- The second spin box sets the number of spaces between the DXCC and the distance/azimuth field.
You can increase or decrease the default number. 

- The first spin box works also when "Align DXCC / distance / azimuth" is not checked.  It can be used to increase the spacing between
the decoded messages and the DXCC names  because the number of stations with non-standard callsigns has greatly increased,
and a little more space might be appropriate.

image::showgrid1.png[align="center",alt="showgrid1"]

Some checkboxes have been repositioned to make it a bit more compact and intuitive. The "Show country information for all messages" 
checkbox has been moved to the General tab and renamed "Show DXCC for all messages" so that the three content-related
checkboxes are now arranged directly next to each other. 

The following screen shot shows the Band Activity pane with "Show distance in messages with gid", "Show azimuth in messages with grid"
and "Align DXCC / distance / azimuth" enabled.

image::showgrid2.png[align="center",alt="showgrid2"]

=== Mouse commands and keyboard shortcuts

_Wsjt-x_improved_ has a number of additional special mouse commands and keyboard shortcuts, available via the *Help* menu.
These are shown below:

image::specialcommands.png[align="center",alt="specialcommands"]

image::specialcommands2.png[align="center",alt="specialcommands2"]

=== LiveCQ

LiveCQ is a tool for sending your decodes of other stations' CQ calls  from QMAP or MAP65 via the internet to a website for others to view.
The spots include all the information needed  to allow the spotted station to be found on the band, including the mode in use.
You can also make use of it to see whether other stations can decode your own CQ calls. It has also been used for monitoring 
who you are receiving if you are away from the shack, using a mobile device viewing the website.

Spots from QMAP are formatted to show the sked frequency and audio offset in use, assuming
of course that the calling station is using the CFOM Doppler method. 

Spotting requires no action on your part, and is fully automatic.  If for any reason you do not wish to upload spots, this can be
accomplished by selecting the 'Other' radio button in the settings, and leaving the adjacent field blank.  However, we do reommend to upload 
spots, since this benefits everyone!

The URL where LiveCQ spots are displayed is 

https://w3sz.com/livecq.html

The layout of the webpage is shown below.

image::livecq.png[align="center",alt="livecq"]

The buttons allow you to select only spots from specific bands.  The buttons are toggled on and off and are active when highlighted.
‘None’ will clear all buttons, so you can select which band you are interested in with one mouse click.  ‘All’ will show all bands.
You may view combinations of bands. If you wish to see spots from a specific spotting station (‘spotter’) or for a specific station
being spotted (‘spottee’) use the checkbox and dialogue box below the buttons. Options for further customising the display are selected
from the checkboxes above the buttons.

TIP: If it seems that the webpage is not displaying correctly,  press CTRL+F5 to refresh the page



=== Miscellaneous Features

.Map grid locators to U.S. States

US States can be optionally appended to the decoded messages.  The required settings (in *File | Settings | General*) are
shown below.  The display of States can be configured for CQ calls only, or both CQ calls and all other messages containing
a grid locator.  Where a grid locator overlaps more than one State, the possibilites are presented.

image::USstates.png[align="center",alt="USstates"]


.Search the DX Call on qrz.com, hamqth.com, or qrzcq.com 

Provided you have an internet connection, it is possible to search for details of a station with one mouse click.

image::searchcalls.png[align="center",alt="searchcalls"]

- Right-click on the Lookup button --> Search for the DX Call on qrz.com
- Right-click on the Add button --> Search for the DX Call on hamqth.com 
- Right-click on the Ignore button --> Search for the DX Call on qrzcq.com

.Tx until 73 is received (MSK144/Q65)

Normally WSJT-X will send only one 73 message.  In some cases it may be desirable to send more than one, which can be enabled using 
the checkbox *MSK144/Q65: Tx until 73 is received* in *File | Settings | General*) Behavior group. A maximum of 10 attempts 
are made before it times out if a 73 message has not yet been received. Use the *Wait & Reply* feature described above in case 
this is still not enough for you.

.CQ: First / CQ: Max Dist / CQ: Max dB / CQ: Min dB

Using the control on the main window, If selected and CQ is called, the program will respond to the first / most distant
/ strongest / weakest station. 

image::cqchoice.png[align="center",alt="cqchoice"]

.Improvements for Fox operators 
Inadvertent transmissions on frequencies overlapping the WSPR sub-bands is prevented. Furthermore, the Fox operator is notified if there is probably another Fox station on the frequency.

image::fox_mode_warning.png[align="center",alt="Second Fox on frequency"] 

.Advanced logging options
*Special operating activity to comments* allows adds information about the special operating activity used to the Comments field. For example, "PACC Contest" is automatically logged for FT Roundup messages when PACC was selected as Contest Name.

image::log_comments1.png[align="center",alt="log_comments1"] 

image::log_comments2.png[align="center",alt="log_comments2"] 

*Log Satellite name and mode* The “Log QSO” window has additional fields where you can log the satellite name and mode. The satellite data is read from the “sat.dat” file.

image::log_comments3.png[align="center",alt="log_comments3"] 

.Right-click the Tune button to initiate rig tuning (ATU)

With some rig models, you can initiate ATU rig tuning directly from the program. This feature requires that your rig is connected via hamlib, and that your rig model is equipped with an ATU.

image::rig_tuning.png[align="center",alt="rig_tuning"] 

.Cloudlog support

The program is able to upload your QSOs to Cloudlog. Cloudlog is an open-source PHP & MySQL based amateur radio logging application. Find more information at https://www.magicbug.co.uk/cloudlog/. Activate the “Enable Cloudlog Features” checkbox (in *File | Settings | Advanced*) and enter your user data.

.Download CALL3.TXT master files

The CALL3.TXT file optionally used by some modes (e.g. JT65) can be updated from the *File|Settings|Colors* tab.